Uniden America Corporation UT051 ユーザーズマニュアル
Channels 15
GMRS/7
FRS
Sub Codes
38 Sub-Audible Tones
121 DCS Codes
Operating Frequency UHF 462.5500 - 467.7125 MHz
Power Source
Power Source
NiMH Battery Pack (BP40) or
4 AAA Alkaline Batteries
Range
Channel 1-7 up to 28 miles
Channel 8-14 up to 5 miles
Channel 15-22 up to 28 miles
Battery Life
12 Hours typ. -
Alkaline
Batteries
(5/5/90 duty cycle)
12 Hours typ. - NiMH
Battery
Pack
Frequency Chart
Ch. Freq.
Cross Ref.
Ch. Freq.
Cross Ref.
1 462.5625 FRS & GMRS 1
12 467.6625 FRS 12
2 462.5875 FRS & GMRS 2
13 467.6875 FRS 13
3 462.6125 FRS & GMRS 3
14 467.7125 FRS 14
4 462.6375 FRS & GMRS 4
15 462.5500 GMRS 11
5 462.6625 FRS & GMRS 5
16 462.5750 GMRS 8
6 462.6875 FRS & GMRS 6
17 462.6000 GMRS 12
7 462.7125 FRS & GMRS 7
18 462.6250 GMRS 9
8 467.5625 FRS 8
19 462.6500 GMRS 13
9 467.5875 FRS 9
20 462.6750 GMRS 10
10 467.6125 FRS 10
21 462.7000 GMRS 14
11 467.6375 FRS 11
22 462.7250 GMRS 15
CTCSS Chart (Hz)
Code Freq.
Code Freq.
oF OFF
20 131.8
1 67.0
21 136.5
2 71.9
22 141.3
3 74.4
23 146.2
4 77.0
24 151.4
5 79.7
25 156.7
6 82.5
26 162.2
7 85.4
27 167.9
8 88.5
28 173.8
9 91.5
29 179.9
10 94.8
30 186.2
11 97.4
31 192.8
12 100.0
32 203.5
13 103.5
33 210.7
14 107.2
34 218.1
15 110.9
35 225.7
16 114.8
36 233.6
17 118.8
37 241.8
18 123.0
38 250.3
19 127.3
Important: Evidence of original purchase is
required for warranty service.
WARRANTOR: UNIDEN AMERICA
CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants,
for three years, to the original retail owner, this
Uniden Product to be free from defects in materials
and craftsmanship with only the limitations or
exclusions set out below.
WARRANTY DURATION: This warranty to the
original user shall terminate and be of no further
effect 36 months after the date of original retail
sale. The warranty is invalid if the Product is:
(A) damaged or not maintained as reasonable or
necessary, (B) modified, altered, or used as part
of any conversion kits, sub-assemblies, or any
configurations not sold by Uniden, (C) improperly
installed, (D) serviced or repaired by someone
other than an authorized Uniden service center for
a defect or malfunction covered by this warranty,
(E) used in any conjunction with equipment or parts
or as part of any system not manufactured by
Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner’s manual for
this product.
STATEMENT OF REMEDY: In the event that the
product does not conform to this warranty at any
time while this warranty is in effect, warrantor will
either, at its option, repair or replace the defective
unit and return it to you without charge for parts,
service, or any other cost (except shipping and
handling) incurred by warrantor or its
representatives in connection with the performance
of this warranty. Warrantor, at its option, may
replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE
IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU
OF AND EXCLUDES ALL OTHER WARRANTIES
OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.THIS WARRANTY
DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OVERPAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or limitation
of incidental or consequential damages so the
above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you
specific legal rights, and you may also have other
rights which vary from state to state. This warranty
required for warranty service.
WARRANTOR: UNIDEN AMERICA
CORPORATION ("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants,
for three years, to the original retail owner, this
Uniden Product to be free from defects in materials
and craftsmanship with only the limitations or
exclusions set out below.
WARRANTY DURATION: This warranty to the
original user shall terminate and be of no further
effect 36 months after the date of original retail
sale. The warranty is invalid if the Product is:
(A) damaged or not maintained as reasonable or
necessary, (B) modified, altered, or used as part
of any conversion kits, sub-assemblies, or any
configurations not sold by Uniden, (C) improperly
installed, (D) serviced or repaired by someone
other than an authorized Uniden service center for
a defect or malfunction covered by this warranty,
(E) used in any conjunction with equipment or parts
or as part of any system not manufactured by
Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner’s manual for
this product.
STATEMENT OF REMEDY: In the event that the
product does not conform to this warranty at any
time while this warranty is in effect, warrantor will
either, at its option, repair or replace the defective
unit and return it to you without charge for parts,
service, or any other cost (except shipping and
handling) incurred by warrantor or its
representatives in connection with the performance
of this warranty. Warrantor, at its option, may
replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE
IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU
OF AND EXCLUDES ALL OTHER WARRANTIES
OF ANY NATURE WHATSOEVER, WHETHER
EXPRESS, IMPLIED OR ARISING BY
OPERATION OF LAW, INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.THIS WARRANTY
DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OVERPAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow this exclusion or limitation
of incidental or consequential damages so the
above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you
specific legal rights, and you may also have other
rights which vary from state to state. This warranty
is void outside the United States of America and
Canada.
PROCEDURE FOR OBTAINING PERFORMANCE
OF WARRANTY: If, after following the instructions
in the owner’s manual you are certain that the
Product is defective, pack the Product carefully
(preferably in its original packaging). Disconnect
the battery from the Product and separately secure
the battery in its own separate packaging within the
shipping carton. The Product should include all
parts and accessories originally packaged with the
Product. Include evidence of original purchase and
a note describing the defect that has caused you to
return it.The Product should be shipped freight
prepaid, by traceable means, to warrantor at:
Canada.
PROCEDURE FOR OBTAINING PERFORMANCE
OF WARRANTY: If, after following the instructions
in the owner’s manual you are certain that the
Product is defective, pack the Product carefully
(preferably in its original packaging). Disconnect
the battery from the Product and separately secure
the battery in its own separate packaging within the
shipping carton. The Product should include all
parts and accessories originally packaged with the
Product. Include evidence of original purchase and
a note describing the defect that has caused you to
return it.The Product should be shipped freight
prepaid, by traceable means, to warrantor at:
THREE YEAR LIMITED WARRANTY
Uniden America Service
4700 Amon Carter Blvd. Fort Worth, TX 76155
(800) 297-1023 during regular business hours (CST)
(See www.uniden.com for current hours of operation.)
© 2010 Uniden America Corporation
All rights reserved Printed in Vietnam
UTZZ01051ZZ(0)
All rights reserved Printed in Vietnam
UTZZ01051ZZ(0)
SPECIFICATIONS
DCS Code List
REGULATORY INFORMATION
WARNING! Read this information before using
the radio. In August 1996 the Federal
Communications Commission (FCC) of the United
States with its action in Report and Order FCC
96-326 adopted an updated safety standard for
human exposure to radio frequency
electromagnetic energy emitted by FCC regulated
transmitters.
Those guidelines are consistent with the safety
standard previously set by both U.S. and
international standards bodies. The design of the
radio complies with the FCC guidelines and these
international standards.
Never allow children to operate the radio without
adult supervision and the knowledge of the
following guidelines.
WARNING! It is up to the user to properly operate
this radio transmitter to insure safe operation.
Please adhere to the following:
Use only the supplied or an approved antenna.
Unauthorized antennas, modifications, or
attachments could impair call quality, damage the
radio, or result in violation of FCC regulations.
Do not use the radio with a damaged antenna.
If a damaged antenna comes into contact with the
skin, a minor burn may result. Please contact your
local dealer for a replacement antenna.
Hand-held Operation (Held-to-Face)
This device was evaluated for typical hand-held
(held-to-face) operations with a 1 inch spacing from
the front of the radio. For hand-held operation, the
radio should be held 1 inch from the user's face in
order to comply with FCC RF exposure
requirements.
Body-worn Operation
This device was evaluated for body-worn operations
with the supplied belt-clip accessory. In order to
comply with FCC RF exposure requirements for
body-worn operations, the radio should only be worn
with the supplied belt-clip accessory or accessory
which does not contain metallic components and
provides a minimum of 3/5 inch separation distance
between the back side of the radio and the user's
body.
For more information about RF exposure, please
visit the FCC web site at www.fcc.gov.
the radio. In August 1996 the Federal
Communications Commission (FCC) of the United
States with its action in Report and Order FCC
96-326 adopted an updated safety standard for
human exposure to radio frequency
electromagnetic energy emitted by FCC regulated
transmitters.
Those guidelines are consistent with the safety
standard previously set by both U.S. and
international standards bodies. The design of the
radio complies with the FCC guidelines and these
international standards.
Never allow children to operate the radio without
adult supervision and the knowledge of the
following guidelines.
WARNING! It is up to the user to properly operate
this radio transmitter to insure safe operation.
Please adhere to the following:
Use only the supplied or an approved antenna.
Unauthorized antennas, modifications, or
attachments could impair call quality, damage the
radio, or result in violation of FCC regulations.
Do not use the radio with a damaged antenna.
If a damaged antenna comes into contact with the
skin, a minor burn may result. Please contact your
local dealer for a replacement antenna.
Hand-held Operation (Held-to-Face)
This device was evaluated for typical hand-held
(held-to-face) operations with a 1 inch spacing from
the front of the radio. For hand-held operation, the
radio should be held 1 inch from the user's face in
order to comply with FCC RF exposure
requirements.
Body-worn Operation
This device was evaluated for body-worn operations
with the supplied belt-clip accessory. In order to
comply with FCC RF exposure requirements for
body-worn operations, the radio should only be worn
with the supplied belt-clip accessory or accessory
which does not contain metallic components and
provides a minimum of 3/5 inch separation distance
between the back side of the radio and the user's
body.
For more information about RF exposure, please
visit the FCC web site at www.fcc.gov.
RF EXPOSURE INFORMATION
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Important: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this device. Your radio is set up to transmit
a regulated signal on an assigned frequency. It is
against the law to alter or adjust the settings inside
the radio to exceed those limitations. Any
adjustments to your radio must be made by
qualified technicians.
To be safe and sure:
• Never open your radio’s case.
• Never change or replace anything in your radio
except the batteries.
Your radio might cause TV or radio interference
even when it is operating properly. To determine
whether your radio is causing the interference, turn
it off. If the interference goes away, your radio is
causing it. Try to eliminate the interference by
moving your radio away from the receiver. If you
cannot eliminate the interference, the FCC requires
that you stop using the radio.
Hazardous Environments: Do not operate the
radio in hazardous environments. Explosion or fire
may result. Do not operate the radio near
unshielded electrical blasting caps.
Under certain conditions, radios can interfere with
blasting operations and may cause an explosion.
Turn your radio OFF to prevent accidental
transmission when in a blasting area or in areas
posted: "Turn off two-way radio." Construction
crews often use remote control RF devices to set
off explosives.
Care and Safety: To clean the radio, use a soft
cloth dampened with water. Do not use cleaners or
solvents because they can harm the body of the
unit and leak inside, causing permanent damage.
Use a dry, lint-free cloth to clean the battery
contacts.
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Important: Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this device. Your radio is set up to transmit
a regulated signal on an assigned frequency. It is
against the law to alter or adjust the settings inside
the radio to exceed those limitations. Any
adjustments to your radio must be made by
qualified technicians.
To be safe and sure:
• Never open your radio’s case.
• Never change or replace anything in your radio
except the batteries.
Your radio might cause TV or radio interference
even when it is operating properly. To determine
whether your radio is causing the interference, turn
it off. If the interference goes away, your radio is
causing it. Try to eliminate the interference by
moving your radio away from the receiver. If you
cannot eliminate the interference, the FCC requires
that you stop using the radio.
Hazardous Environments: Do not operate the
radio in hazardous environments. Explosion or fire
may result. Do not operate the radio near
unshielded electrical blasting caps.
Under certain conditions, radios can interfere with
blasting operations and may cause an explosion.
Turn your radio OFF to prevent accidental
transmission when in a blasting area or in areas
posted: "Turn off two-way radio." Construction
crews often use remote control RF devices to set
off explosives.
Care and Safety: To clean the radio, use a soft
cloth dampened with water. Do not use cleaners or
solvents because they can harm the body of the
unit and leak inside, causing permanent damage.
Use a dry, lint-free cloth to clean the battery
contacts.
Tone Octal
No. Code
39 023
40 025
41 026
42 031
43 032
44 043
45 047
46 051
47 054
48 065
49 071
50 072
51 073
52 074
53 114
54 115
55 116
56 125
57 131
58 132
59 134
60 143
61 152
62 155
63 156
64 162
65 165
66 172
No. Code
39 023
40 025
41 026
42 031
43 032
44 043
45 047
46 051
47 054
48 065
49 071
50 072
51 073
52 074
53 114
54 115
55 116
56 125
57 131
58 132
59 134
60 143
61 152
62 155
63 156
64 162
65 165
66 172
Tone Octal
No. Code
67 174
68 205
69 223
70 226
71 243
72 244
73 245
74 251
75 261
76 263
77 265
78 271
79 306
80 311
81 315
82 331
83 343
84 346
85 351
86 364
87 365
88 371
89 411
90 412
91 413
92 423
93 431
94 432
No. Code
67 174
68 205
69 223
70 226
71 243
72 244
73 245
74 251
75 261
76 263
77 265
78 271
79 306
80 311
81 315
82 331
83 343
84 346
85 351
86 364
87 365
88 371
89 411
90 412
91 413
92 423
93 431
94 432
Tone Octal
No. Code
95 445
96 464
97 465
98 466
99 503
100 506
101 516
102 532
103 546
104 565
105 606
106 612
107 624
108 627
109 631
110 632
111 654
112 662
113 664
114 703
115 712
116 723
117 731
118 732
119 734
120 743
121 754
No. Code
95 445
96 464
97 465
98 466
99 503
100 506
101 516
102 532
103 546
104 565
105 606
106 612
107 624
108 627
109 631
110 632
111 654
112 662
113 664
114 703
115 712
116 723
117 731
118 732
119 734
120 743
121 754
LCD Backlight
The LCD Backlight automatically turns ON when any
The LCD Backlight automatically turns ON when any
key (except the PTT button) is pressed. The LCD
display illuminates for 10 seconds before turning
OFF.
Roger Beep
Roger Beep is a BEEP that is sent to notify the end of
Roger Beep is a BEEP that is sent to notify the end of
transmission (both PTT and VOX transmission).
Roger Beep can be heard through the speaker when
both Roger beep and Key Beep are set to ON. When
Roger beep is set to ON and Key Beep OFF, Roger
Beep will not be heard from the speaker but it will be
transmitted to your party. When Roger Beep is set to
OFF, Roger Beep neither be herad nor transmitted.
To turn ON Roger Beep:
Press and hold the CH key while turning ON the
radio.
To turn OFF Roger Beep:
Press and hold the CH key while turning ON the
radio.
Press and hold the CH key while turning ON the
radio.
To turn OFF Roger Beep:
Press and hold the CH key while turning ON the
radio.
LCD Backlight
The LCD Backlight automatically turns ON when any
The LCD Backlight automatically turns ON when any
key (except the PTT button) is pressed. The LCD
display illuminates for 10 seconds before turning
OFF.
Roger Beep
Roger Beep is a BEEP that is sent to notify the end of
Roger Beep is a BEEP that is sent to notify the end of
transmission (both PTT and VOX transmission).
Roger Beep can be heard through the speaker when
both Roger beep and Key Beep are set to ON. When
Roger beep is set to ON and Key Beep OFF, Roger
Beep will not be heard from the speaker but it will be
transmitted to your party. When Roger Beep is set to
OFF, Roger Beep neither be herad nor transmitted.
To turn ON Roger Beep:
Press and hold the CH key while turning ON the
radio.
To turn OFF Roger Beep:
Press and hold the CH key while turning ON the
radio.
Press and hold the CH key while turning ON the
radio.
To turn OFF Roger Beep:
Press and hold the CH key while turning ON the
radio.
RBRC INFORMATION
As part of our commitment to
protect the environment and
conserve natural resources,
Uniden voluntarily participates in
an RBRC® industry program to
collect and recycle used Ni-MH
batteries within the US.
Please call 1-800-8-BATTERY for information on
Ni-MH battery recycling in your area. (RBRC® is a
registered trademark of the Rechargeable Battery
Recycling Corporation.)
protect the environment and
conserve natural resources,
Uniden voluntarily participates in
an RBRC® industry program to
collect and recycle used Ni-MH
batteries within the US.
Please call 1-800-8-BATTERY for information on
Ni-MH battery recycling in your area. (RBRC® is a
registered trademark of the Rechargeable Battery
Recycling Corporation.)
UT051ZV_GMR2838-2CK (ST RoHS) UAC_1110.indd 2
UT051ZV_GMR2838-2CK (ST RoHS) UAC_1110.indd 2
11/10/2010 1:48:41 PM
11/10/2010 1:48:41 PM