VeriFone OMNI3600D ユーザーズマニュアル



 2003 VeriFone, Inc. All rights reserved. 

VeriFone, Inc.

2455 Augustine Drive

Santa Clara CA 95054-3002

Tel: 800-VeriFone (837-4366)

VeriFone Part Number: 22475

 

Revision E

Manufacturer: VeriFone, Inc.

Model: Omni 3600

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions:  (1)  this device may not 
cause harmful interference, and (2)  this device must accept any interference received, including interference that may cause 
undesired operation.

To comply with the FCC RF exposure requirements, bystanders and parts of the users body other then the extremities must be at 
least 15.0mm away from the device.

SAR compliance for body worn operating configurations is limited to the specific belt clips / holsters / accessories that have no 
metallic component in the assembly. The highest reported SAR values for Omni 3600C under the FCC ID B32OMNI3600C are: 
PMS modes (Part 22) – Body-worn 0.0056mW/g. The highest reported SAR values for Omni 3600D under the FCC ID 
B32OMNI3600D are: PMS modes (Part 22) – Body-worn 0.309mW/g, PCS mode (Part 24) - Body-worn: 0.232mW/g.

"""O terminal Omni 3600 atende aos limites da Taxa de Absorção Específica referente à exposição a campos elécticos, magnéticos 
e electromagnéticos de radiofreqüências adoptados pela Anatel."""

SAR compliance for body worn operating configurations is limited to the specific belt clips / holsters / accessories that have no 
metallic component in the assembly. The highest reported SAR values under this FCC ID are: PMS modes (Part 22) – Body-worn 
0.245mW/g, PCS mode (Part 24) - Body-worn: 0.218mW/g.

Please switch off and do not operate the equipment when in an area with a potentially explosive atmosphere, such as refueling 
points, fuel depots or storage areas, chemical plants, and blasting operations.

Do not:

•

disassemble, crush, puncture, or incinerate in fire. 

•

short circuit contacts. 

•

expose to temperatures exceeding 140

°

F (60

°

C).

Before you connect the terminal power pack to an electrical outlet, check that the on/off power switch on the terminal is off. If the 
terminal does not have an on/off switch, check that the power cable connector is removed from the terminal’s power port.

or 

When connecting the terminal to a power pack, always connect the three-pronged plug of the power pack to an electrical wall outlet 
first. Then connect the power cable to the terminal’s power port.

The AC adapter is designed to ensure your personal safety and to be compatible with this equipment. Please follow these 
guidelines:

•

Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet are wet.

•

Allow adequate ventilation around the adapter. Avoid locations with restricted airflow.

•

Connect the adapter to a proper power source. The voltage and grounding requirements are found on the product case and/or 
packaging.

•

Do not use the adapter if the cord becomes damaged.

•

Do not attempt to service the adapter. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to 
excess moisture.

Some peripherals require a separate power source. Before connecting a check reader or similar device, turn off power to the 
terminal.

Before connecting any peripheral device, turn off power to the terminal. Turn on power only after you are finished connecting the 
peripheral device(s). For complete information about peripheral installation and use, please refer to the user documentation 
supplied with those devices.

Disconnecting power during a transaction may cause transaction data files that are not yet stored in terminal memory to be lost.

To protect your terminal against possible damage caused by lightning strikes and electrical surges, you may want to install a power 
surge protector.

CAUTION: Due to risk of electrical shock or terminal damage, do not use the terminal near water, including a bathtub, wash bowl, 
kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Also, avoid using this product during electrical storms.

Avoid locations near electrical appliances or other devices that cause excessive voltage fluctuations or emit electrical noise (for 
example, air conditioners, neon signs, high-frequency or magnetic security devices, or electric motors).

Carefully inspect the shipping carton and its contents for any damage. If the terminal or any product component appears damaged 
or tampered with, immediately notify the shipping company and your VeriFone distributor or service provider.

CAUTION: Do not use a terminal that has been damaged or tampered with.

Unless otherwise instructed in this document, do not, under any circumstances, attempt any service, adjustments, or repairs on this 
equipment. Instead, contact your local VeriFone distributor or service provider for assistance. Failure to comply may invalidate the 
product warranty.

Do not plug the power pack into an outdoor outlet or operate the terminal outdoors. It is not waterproof or dustproof, and is for 
indoor use only. Any damage to the unit from exposure to rain or dust may void your warranty.

Do not use the terminal where there is high heat, dust, humidity, moisture, or caustic chemicals or oils. Keep the terminal away from 
direct sunlight and anything that radiates heat, such as a stove or a motor.

Never use thinner, trichloroethylene, or ketone-based solvents to clean the terminal — they may deteriorate plastic or rubber parts. 
Do not spray cleaners or other solutions directly onto the keypad or display. For best results, use a VeriFone Cleaning Kit or a clean 
cloth dampened with water and mild soap. To remove stubborn stains, use alcohol or an alcohol-based cleaner.

Select a location for your terminal that contributes to its ease of use:

•

A location convenient for both merchant and cardholder.

•

A flat support surface, such as a countertop or table.

•

A location near a power outlet and a telephone/modem line connection.

WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the 

user’s authority to operate this equipment.

continued