Brother Industries Ltd. 8VA652 ユーザーズマニュアル

• Always use the specified voltage and the included AC adapter (AD-E001) for the 

P-touch labeler to prevent any damage or failure.

• Do not touch the P-touch labeler during a lightning storm.

• Do not use the P-touch labeler/AC adapter in places of high humidity such as 

bathrooms.

• Do not overload the power cord.

• Do not place heavy objects on, or damage the P-touch labeler, power cord or plug. 

Do not forcibly bend or pull the power cord. Always hold the AC adapter when 

disconnecting from the power outlet.

• Make sure that the plug is fully inserted in the power outlet. Do not use an outlet that 

is loose.

• Do not allow the P-touch labeler/AC adapter/power plug/batteries to get wet, for 

example, by handling them with wet hands or spilling beverages on to them.

• Do not disassemble or modify the P-touch labeler/AC adapter/batteries.

• Do not allow a metal object to contact both the plus and minus ends of a battery.

• Do not use sharp objects, such as tweezers or a metallic pen, to change the batteries.

• Do not throw the batteries into fire or expose to heat.

• Disconnect the AC adapter, remove batteries immediately and stop using the 

P-touch labeler if you notice abnormal odor, heat, discoloration, deformation or 

anything unusual while using or storing it.

• Do not use a damaged or leaking battery as the fluid may get on your hands.

• Do not use a deformed or leaking battery or one whose label is damaged. There is 

a possibility of damaging the P-touch labeler.

• Since loss of eyesight may result if leaked fluid from batteries gets into your eyes, 

immediately rinse your eyes with a large amount of clean water, and then seek 

medical attention.

• When the P-touch labeler is not being used, store it out of the reach of children. In 

addition, do not allow children to put any P-touch labeler parts or labels in their 

mouths. If any object has been swallowed, seek medical attention.

• Do not touch metal parts around the print head immediately after printing.

• Do not touch the cutter blade. (See Unpacking the PT-P750W & Parts Description.)

• If leaked fluid from batteries gets on your skin or clothes, immediately rinse them 

with clean water.

• Remove the batteries and disconnect the AC adapter if you do not intend to use the 

P-touch labeler.

• Do not use any batteries other than those specified. Do not use combinations of old 

and new batteries or combinations of different types, different charging levels, 

different manufacturers or different models. Do not insert a battery with its plus and 

minus ends reversed.

• Do not drop or hit the P-touch labeler/AC adapter.

• Do not put your finger inside the P-touch labeler when you close the cassette cover.

• Before using Ni-MH rechargeable batteries, carefully read the instructions for the 

batteries and battery charger, and be sure to use them correctly.

• When using Ni-MH rechargeable batteries, charge the batteries with a specialized 

battery charger before using the batteries.

• Do not put your finger inside the tape exit slot. You could be injured by the cutter blade.

• Depending on the location, material, and environmental conditions, the label may 

unpeel or become irremovable, the color of the label may change or be transferred 

to other objects. Before applying the label, check the environmental conditions and 

the material.

• Do not use the P-touch labeler in any way or for any purpose not described in this 

guide. Doing so may result in accidents or damage to the P-touch labeler.

• Use only Brother TZe tapes with the P-touch labeler. Do not use tapes that do not 

have the 

 mark.

• Only use a soft, dry cloth to clean the P-touch labeler; never use alcohol or other 

organic solvents.

• Use a soft wipe to clean the print head; never touch the print head with your fingers.

• Do not put any foreign objects into the tape exit slot, the AC adapter connector or 

battery compartment, etc.

• Do not place the P-touch labeler/batteries/AC adapter in direct sunlight or rain, near 

heaters or other hot appliances, in any location exposed to extremely high or low 

temperatures (e.g., on the dashboard or in the back of your car), high humidity, or 

in dusty locations.

• Do not try to print if the cassette is empty; it will damage the print head.

• Do not pull the tape while printing or feeding; it will damage the tape and the P-touch 

labeler.

• Any data stored in memory will be lost due to failure or repair of the P-touch labeler, 

or if the batteries expire.

• The P-touch labeler is not equipped with a charging feature for rechargeable batteries.

• The length of the printed label may differ from the displayed label length on the 

computer.

• A protective clear plastic sticker is placed over the top panel during manufacturing 

and shipping. This sticker should be removed prior to use.

• When printing multiple copies of a label or using the numbering function printing, the 

P-touch labeler will not detect the end of the tape cassette and will continue operating.

• When using Heat Shrink Tube, the printing area will be smaller than when using 

normal tape.

• If you connect a mobile device to the P-touch labeler using the NFC function without 

installing a specialized application, the Apps section of Google Play may be 

displayed on your mobile device automatically. 

You may be charged a communication fee for this service.

This product includes open-source software.

To see the open source licensing remarks, please go to the manual download 

selection on your model's home page of Brother Solutions Center at

http://solutions.brother.com/.

The available scientific evidence does not show that any health problems are associated with 

using low power wireless devices. There is no proof, however, that these low power wireless 

devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency 

energy (RF) in the microwave range while being used. Whereas high levels of RF can produce 

health effects (by heating tissue), exposure of low-level RF that does not produce heating 

effects causes no known adverse health effects. Many studies of low-level RF exposures have 

not found any biological effects. Some studies have suggested that some biological effects 

might occur, but such findings have not been confirmed by additional research. PT-P750W has 

been tested and found to comply with FCC radiation exposure limits set forth for an 

uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.

BROTHER is either a trademark or a registered trademark of Brother Industries, Ltd.

P-TOUCH is a trademark or registered trademark of Brother Industries, Ltd.

© 2014 Brother Industries, Ltd. All rights reserved.

Microsoft, Windows Vista, Windows Server and Windows are either registered 

trademarks or trademarks of Microsoft Corp. in the United States and/or other countries.

Apple, Macintosh, Mac OS, iPhone, iPad and iPod are trademarks of Apple Inc., 

registered in the United States and other countries.

The names of other software or products used in this document are trademarks or 

registered trademarks of the respective companies that developed them.

Wi-Fi and Wi-Fi Alliance are registered trademarks of the Wi-Fi Alliance.

Each company whose software title is mentioned in this manual has a Software 

LicenseLicence Agreement specific to its proprietary programs.

Any trade names and product names of companies appearing on Brother products, 

related documents and any other materials are all trademarks or registered trademarks 

of those respective companies.

Indicates a potentially hazardous situation which, if not 

avoided, could result in death or serious injuries.

Indicates a potentially hazardous situation which, if not 

avoided, may result in minor or moderate injuries.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. 

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Responsible Party: Brother Mobile Solutions, Inc.

100 Technology Drive Suite 250A

Broomfield, CO 80021 U.S.A.

Tel: (303) 460-1600

Product Name :

Brother P-touch Electronic Labeling System

Model Number :

PT-P750W

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions: (1) this device may not cause harmful interference, and 

(2) this device must accept any interference received, including interference that 

may cause undesired operation.
PT-P750W is equipped with FCC ID:B3Q8VA652.
This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 

provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by 

turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• This transmitter must not be co-located or operated in conjunction with any other 

antenna or transmitter.

Important
• The enclosed interface cable should be used in order to ensure compliance with 

the limits for a Class B digital device.

• Changes or modifications not expressly approved by Brother Industries, Ltd. 

could void the user's authority to operate the equipment.

* In case WLAN Interface is in use.

CAUTION: To maintain compliance with FCC’s RF exposure guidelines, use only 

the supplied antenna. Unauthorize antenna, modification, or attachments could 

damage the transmitter and may violate FCC regulations.

The purpose of the International ENERGY STAR

®

 Program is 

to promote the development and popularization of 

energy-efficient office equipment. As an ENERGY STAR

®

Partner, Brother Industries, Ltd. has determined that this 

product meets the ENERGY STAR

®

 guidelines for energy 

efficiency.

Carefully observe the following precautions for the rechargeable Li-ion battery 

(hereafter referred to as "rechargeable battery"), If these precautions are not followed, 

overheating, leaking, or cracks in the battery may result in an electrical short, 

explosion, smoke, fire, electric shock, injury to yourself or others, or damage to the 

product or other property.

• Use the rechargeable battery only for its intended purpose. The P-touch labeler and 

rechargeable battery are designed to function exclusively with each other. Do not insert 

a different rechargeable battery into the P-touch labeler or insert the rechargeable 

battery into a different P-touch labeler, otherwise fire or damage may result.

• To charge the rechargeable battery, insert the rechargeable battery into the 

P-touch labeler, and then use the AC adapter designed specifically for this 

P-touch labeler.

• DO NOT charge the rechargeable battery near a fire or in direct sunlight. This could 

activate the protection circuitry, which is designed to prevent danger from high heat. 

Activation of the protection circuitry could cause charging to stop, charging to occur 

with excessive current or voltage if the protection circuitry fails, or an abnormal 

chemical reaction within the battery.

• When charging the rechargeable battery, use only a battery charger designed 

specifically for the rechargeable battery.

• DO NOT allow wires or other metal objects to come into contact with the terminals 

of the rechargeable battery. Do not carry or store the rechargeable battery with 

metal objects such as necklaces or hairpins. This could cause an electrical short, 

and cause metal objects to overheat.

• DO NOT use or leave the rechargeable battery near fire, heaters, or other high 

temperature (above 176°F/80°C) locations.

• DO NOT allow the rechargeable battery to come into contact with or to be immersed 

in water.

• DO NOT use the rechargeable battery in corrosive environments, such as areas 

where salty air, salt water, acids, alkalis, corrosive gases, chemicals, or any 

corrosive liquid are present.

• DO NOT use the rechargeable battery if it is damaged or leaking.

• DO NOT directly solder any connections to the rechargeable battery. This could 

cause internal insulation to melt, gas to be emitted, or safety mechanisms to fail.

• DO NOT use the rechargeable battery with the polarity (+) (-) reversed. Check the 

orientation of the rechargeable battery before inserting it, and do not try to force the 

rechargeable battery into the P-touch labeler. Charging the rechargeable battery 

with the polarity reversed could cause an abnormal chemical reaction within the 

rechargeable battery or abnormal current flow during discharge.

• DO NOT directly connect the rechargeable battery to a household electrical supply.

• Liquid (electrolyte) leaking from the P-touch labeler or rechargeable battery may 

indicate that the rechargeable battery is damaged. If the rechargeable battery leaks, 

immediately stop using the P-touch labeler, unplug the AC adapter, and isolate the 

P-touch labeler by putting it in a bag. 

Do not touch the electrolyte. If electrolyte gets in the eyes, do not rub the eyes. 

Immediately rinse liberally with tap water or other clean water and seek the advice 

of a medical professional. If left alone, the electrolyte could cause eye damage. If 

electrolyte contacts your skin or clothing, immediately rinse them with water.

• DO NOT put the rechargeable battery, or a P-touch labeler with the rechargeable 

battery installed, into a microwave oven or a high pressure container.

• DO NOT leave the rechargeable battery without power in the main unit for a long period 

of time. This could shorten the life of the rechargeable battery or lead to an electrical short.

• If the P-touch labeler can only be used for a short period of time, even though the 

rechargeable battery is fully charged, the rechargeable battery may have reached 

the end of its service life. Replace the rechargeable battery with a new one. When 

removing and replacing the rechargeable battery, cover the terminals of the old 

rechargeable battery with tape to avoid creating a short in the battery.

• DO NOT disassemble, modify, or attempt to repair the rechargeable battery.

• DO NOT dispose of the rechargeable battery in fire or cause it to overheat. This 

could cause the internal insulation to melt, gas to be emitted, or safety mechanisms 

to fail. Additionally, the electrolyte solution could catch fire.

• DO NOT puncture the rechargeable battery with any objects, subject it to severe 

shocks or throw it. Damage to the rechargeable battery's protection circuit could 

cause the rechargeable battery to be recharged at an abnormal current/voltage or 

cause an abnormal chemical reaction within the rechargeable battery.

• DO NOT incinerate the rechargeable battery or dispose of it with household waste.

„

• Charge the rechargeable Li-ion battery before use. Do not use it before it is charged.

• The rechargeable Li-ion battery charging can take place in 41°F-95°F (5°C-35°C) 

environments. Charge the rechargeable Li-ion battery in an environment in this 

temperature range. If the surrounding temperature is out of this range, the 

rechargeable Li-ion battery will not be charged, and the battery indicator will remain lit.

• If the P-touch labeler is used when both the rechargeable Li-ion battery is installed 

and the AC adapter is connected, the battery indicator may turn off and charging 

may stop even if the rechargeable Li-ion battery has not been fully charged.

„

Understanding the properties of the rechargeable Li-ion battery will allow you to 

optimize its usage.

• Using or storing the rechargeable Li-ion battery in a location exposed to high or low 

temperatures may accelerate its deterioration. In particular, using a rechargeable 

Li-ion battery with a high charge (charged 90% or more) in a location exposed to 

high temperatures will considerably accelerate battery deterioration.

• Using the P-touch labeler while the rechargeable Li-ion battery is installed and 

charging may accelerate the battery’s deterioration. If using the P-touch labeler 

when the rechargeable Li-ion battery is installed, disconnect the AC adapter.

• If the P-touch labeler will not be used for longer than one month, remove the 

rechargeable Li-ion battery from the P-touch labeler, and then store the battery in a 

cool place away from direct sunlight.

• If the rechargeable Li-ion battery will not be used for a long period of time, we 

recommend charging it every 6 months.

• If you touch a part of the device while a Li-ion battery is charging, the device may 

feel warm. This is normal, and the device may be used safely. If the P-touch labeler 

becomes extremely hot, discontinue use.

„

• Charging time: Approximately 6 hours when charged by a AC adapter (AD-E001).

• Nominal Voltage: DC 7.2 V

• Nominal Capacity: 1850 mAh

• Charging current: 800 mA

• Charging voltage: up to 8.2 V (Maximum)

„

To remove the rechargeable Li-ion battery, reverse the installation procedure.

„

The rechargeable Li-ion battery can be charged while it is installed in the P-touch 

labeler.

Perform the following procedure to charge the rechargeable Li-ion battery.

„

To stop the rechargeable Li-ion battery from charging, disconnect the AC adapter cord.

Indicates an imminently hazardous situation which, if the 

product is handled without following the warnings and 

instructions, will result in death or serious injuries.

Surroundings temperature range
Charge

104°F/40°C

Standard discharge current 1.9 A

140°F/60°C

Maximum discharge current 2.5 A

140°F/60°C

Shipped battery

Less than 1 month

-4°F - 122°F/-20°C - 50°C

Less than 3 month

-4°F - 104°F/-20°C - 40°C

Less than 1 year

-4°F - 68°F/-20°C - 20°C

Maximum charging voltage

8.2 Vdc

Maximum charging current

1330 mA

Up to 6 hours is needed to fully charge the rechargeable Li-ion battery.

The Lithium Ion battery you have purchased is recyclable. At the end of its 

useful life, under various state and local laws, it is illegal to dispose of this 

battery into your municipal waste stream. Please call 1-800-8-BATTERY

BA-E001

AD-E001

Charging

Full charge

Check that the package contains the following before using the P-touch labeler. If any 

item is missing or damaged, contact your Brother reseller.

To remove the batteries, reverse the installation procedure.

On: Press the Power button.

Off: Press and hold the Power button until the Status lamp is lit in orange.

1.

Turn on the P-touch labeler (

1), then press and hold down the Editor Lite button 

until the green Editor Lite lamp lights up (

2). Connect the USB cable to the 

computer and PT-P750W.

Please visit our Support website.

You can find following information:

• Software download

• Manuals/Documents

• Frequently Asked Questions (Troubleshooting, Useful tips on using printer)

• Consumable information and the latest OS compatibility information.

You can also see setup steps on the website.
Click the Getting ready to use your printer. link in the "information" section.

The contents of this website are 

subject to change without notice.

• PT-P750W

• AC adapter (AD-E001)

• USB cable

• Starter tape cassette

1

Top panel

2

Editor Lite lamp

3

Editor Lite button

4

Wireless mode button

5

Tape exit slot

6

Wi-Fi lamp

7

NFC  lamp

8

Feed & Cut button

9

Status lamp

10 Battery lamp

11 Power button

12 Battery cover

13 Mini-USB port

14 AC adapter connector

15 Cassette cover

16 NFC tag

17 Release lever

18 Print head

19 Tape cutter

20 Cutter blade

If you cannot close the cassette cover, check to ensure the white lever is in the 

up position. If not, lift the lever, and then attach the cover.

• Make sure that there is no slack in the tape.

• When setting or removing the tape cassette, make sure that the tape does not 

catch on the protrusion (1) or the print head.

14

13

15

5

3

4

1

2

8

9

11

12

17

18

19

20

10

6

7

16

1

• Remove the batteries if you do not intend to use the P-touch labeling system 

for an extended period of time.

• Dispose of the battery at an appropriate collection point, not in the general 

waste stream. In addition, be sure to observe all applicable federal, state, and 

local regulations.

• When storing or discarding the battery, wrap it (for 

example with cellophane tape), to prevent it from 

short-circuiting.

(Battery insulation example)
1. Cellophane tape
2. Alkaline or Ni-MH battery

When turning the P-touch off, keep the AC adapter connected or the batteries 

installed until the Status lamp goes off.

AD-E001

LR6 or HR6

2

1

2

1

2.

After the USB cable is connected, a dialog box appears on the computer display. (The 

following screens may differ depending on the operating system on your computer.)

Click [P-touch Editor Lite].

Click [Open folder to view files], and then double-click [PTLITE10].

On the [Start] screen, click [PT-P750W], [Open folder to view files], and then 

double-click [PTLITE10].

Double-click [PT-P750W] on the desktop and the [P-touch Editor Lite] application icon.

„

a

Exit P-touch Editor Lite by clicking on the 

 in the top right corner of the window 

if using P-touch Editor Lite.

b

To disconnect the P-touch labeler, click the icon in the computer’s task bar (

, 

, or 

).

c

Click [Safely remove USB Mass Storage Device].

d

When the message indicating that the device can be safely removed is 

displayed, turn off the P-touch labeler and disconnect the USB cable.

a

Exit P-touch Editor Lite by clicking on the red button in the top left corner of the 

window, if using the P-touch Editor Lite.

b

Select [PT-P750W] on the desktop, and then perform one of the following:

• Select [Eject] from the Context menu.

• Drag and drop it in the Trash.

c

When a message indicating that the device can be safely removed is displayed, 

turn off the P-touch labeler and disconnect the USB cable.

„

Brother iPrint&Label allows you to use features of your Brother machine directly from 

your mobile device, without using a computer.

Simply search for "Brother iPrint&Label" in the App Store or Google Play.

Please see the Brother Solutions Center (support.brother.com/) for the latest OS 

compatibility information.

More advanced editing functions are available by downloading the printer driver and 

P-touch Editor from our support site, and installing them.

Features of P-touch Editor:

Makes it easy for anyone to create a wide variety of custom labels in complex layouts 

by using fonts, templates, and clip art.

The Status lamp on the P-touch labeler indicates the current operating condition.

„

With the P-touch labeler off, press and hold the Feed & Cut button while holding down 

the Power button. When the Editor Lite lamp starts flashing and the Status lamp lights 

orange, press the Feed & Cut button six times while continuing to hold down the 

Power button. The P-touch labeler will be reset to the factory settings.

Should you have questions, or need information about your Brother product, we have 

a variety of support options for you to choose from:
USA-Customer Service

Telephone: 1-877-BROTHER (1-877-276-8437)

Fax: 1-901-379-1210

Website: www.brother-usa.com

Supplies/Accessories:

www.brothermall.com or 1-877-552-6255

If you are connecting the P-touch labeler via a USB hub, it may not be detected 

correctly.

• If you do not see the dialog box, it may be hidden behind an open software 

program window. Minimize all windows to show the dialog box.

• For details on using P-touch Editor Lite, visit the Brother Solutions Center.

Tape cassette

Brother TZe tape (width)
0.13" (3.5 mm), 0.23" (6 mm), 0.35" (9 mm), 0.47" (12 mm), 
0.70" (18 mm), 0.94" (24 mm)

AC Adapter

AD-E001

Rechargeable Li-ion Battery

BA-E001

Wi-Fi

Green lamp is lit

Connected wirelessly.

Green lamp is flashing

 

 

 

 

 

Not connected wirelessly.

NFC

Not lit

The Wireless Direct mode is disabled (connections 
cannot be made).

Green lamp is lit

The Wireless Direct mode is enabled (connections can 
be made).

Green lamp is litĺGoes

off briefly

An NFC-compatible device was placed near the P-touch 
labeler (NFC tag data was sent).

Green lamp is flashing

 

 

 

 

 

The Wireless Direct settings are being configured (the 
user is connecting a device).

STATUS

Green lamp is lit

Power is ON.

Green lamp is flashing

 

 

 

 

 

Receiving data from the computer.
Transferring data.

Orange lamp is lit

The cassette cover is open. Close the cassette cover 
correctly.
Starting the reset procedure, or the Feed & Cut button 
was pressed during the reset procedure.
For details on resetting the P-touch labeler, see "How to 
Reset the P-touch Labeler".

Orange lamp is flashing

 

 

 

 

 

Cooling (Wait for the temperature to cool down)
Reset in progress. For details on resetting the P-touch 
labeler, see "How to Reset the P-touch Labeler".

Red lamp is lit

The P-touch labeler is booting.

Red lamp is flashing

 

 

 

 

 

Indicates one of the following errors.
Red lamp flashes for 0.9 second intervals:
• No tape cassette
• Incorrect tape cassette installed
• Incompatible tape cassette installed
• The cassette cover was opened during printing
• Transmission error
• Overheating error
• Cutter error
Red lamp flashes for 0.3 second intervals:
• System error

Battery

Not lit

Charging is complete.
The battery is fully charged.

Orange lamp is lit

Charging.

Orange lamp is flashing

 

 

 

 

 

Orange lamp flashes slowly:
The remaining battery level is half or low (the lamp 
flashes faster as the remaining battery level decreases).
Orange lamp flashes for 0.5 second intervals:
Charge the battery.

Printed in China

LAE119001

 

LAE119001