The Genie Company a Division of Overhead Door Corporation UNI4B ユーザーズマニュアル

40681504070, 11/2018

UNIVERSAL REMOTE

INSTRUCTIONS

WARNING

MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.

• DO NOT install transmitter unless the door operator’s safety device works as required by the door

operator’s manual.

• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving

door parts.

• Keep people clear of opening while door is moving.

• DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

• Close door then disconnect opener using the manual release handle.

• DO NOT use transmitter or door operator.

• Refer to Door and Door Opener Owner’s Manuals before attempting any repairs.

FCC Part 15.21 Statement:

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

FCC / IC Statement:

This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation of the device.

For help or answers please contact Customer Care by website chat

(www.geniecompany.com) or by phone at 1-800-354-3643 for programming

assistance.

For

Patent Information: www.geniecompany.com/patent,

STEP 1 - ACTIVATE REMOTE/BUTTON LAYOUT & LED

Activation Tab: Pull tab to activate the remote.

NOT FOR USE WITH ANY GARAGE DOOR OPENER MANUFACTURED PRIOR TO 1993. NON-

CONTACT SAFETY REVERSING SYSTEM (PHOTOCELLS) MUST BE IN PLACE AND OPERATIONAL.

The universal remote can be programmed to operate many brands and types of garage door openers.

Locate the brand and opener specifications by consulting the label on the opener head, the instruction manual, the

current remote controls for the opener, or the original manufacturer of the opener.

Below are the brands and specifications that this remote is compatible with and the methods that can be used to

program them. Use Chart A below to find your opener/specification combination and then proceed to an available

programming method. All combinations shown can be programmed using the CLONING METHOD.

OPTION 3: QUICK START METHOD

You may use 1 of the 4 manufacturer pre-set buttons on the remote as indicated below if you have

any of these brands/specifications. If you have more than one of the same brand/MHz opener and/

or would prefer to use a different button than indicated for your brand by this method, please note

that all 4 buttons can be programmed individually from each other. You may use any combination of

programming methods available for your opener/specification combination to achieve your desired

button setup.

Button 1: Genie Intellicode 1 or Overhead Door CodeDodger I

Button 2: Chamberlain® with a PURPLE LEARN Button

Button 3: Chamberlain® with a ORANGE/RED LEARN Button

Button 4: Chamberlain® with an YELLOW LEARN Button

1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.

2. Press and release the pre-set button on the universal remote that corresponds with your opener

slowly and deliberately several times until the garage door opener operates. If using Chamberlain®

technology with a YELLOW LEARN button, see *ADDITIONAL INSTRUCTIONS. If you are NOT using

Chamberlain® technology with a YELLOW LEARN button, programming for this button is complete.

OPTION 2: LEARN METHOD

PUT THE UNIVERSAL REMOTE INTO LEARN MODE & SELECT A BUTTON

1. Press and hold down the Genie universal remote button #2.

2. While still holding down button #2, press the universal remote button #4 - four times.

3. Release both buttons.

The BLUE LED on the remote will begin flashing. You will have 15 seconds to complete your entry.

4. Press the button of your choice on the universal remote the required number of times indicated

in the LEARN METHOD column next to your opener and specification in Chart A.

Wait the remainder of the 15 seconds. The blue LED will give a long blink and then go out.

PROGRAMMING THE UNIVERSAL REMOTE TO THE OPENER

1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.

2. Press and release the button you just programmed slowly and deliberately several times until

the garage door opener operates. If using Chamberlain® technology with a YELLOW LEARN

button, see *ADDITIONAL INSTRUCTIONS. If you are NOT using Chamberlain® technology with a

YELLOW LEARN button, programming for this button is complete.

OPTION 1: CLONING METHOD

The Genie universal remote can clone an existing operational remote for any of the garage door

opener brands/specification combinations listed in Chart A.

NOTE: During programming, the garage door opener will operate. Ensure that the

garage door opening is clear of personnel or any obstructions.

LED - The LED will light with each button press and

will also light in response to button presses during

different programming modes.

PUT THE UNIVERSAL REMOTE INTO CLONING MODE & SELECT A BUTTON

1. Place the original remote and the Genie universal remote within 2” - 4” of each other.

2. Press and hold down the Genie universal remote button #1.

3. While still holding down button #1, press the universal remote button #2 - four times.

4. Release both buttons.

The WHITE LED on the remote will begin flashing. You will have 20 seconds to complete your entry.

5. Hold down the existing operational button on the original remote until the new universal remote

blinks change from slow WHITE BLINKS to rapid BLUE blinks.

6. Once the universal remote BLUE LED is blinking rapidly, press the button of choice on the

universal remote slowly and deliberately. The LED will turn solid and then go out.

PROGRAM THE UNIVERSAL REMOTE TO THE OPENER

1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.

2. Press and release the button you just programmed slowly and deliberately several times until

the garage door opener operates. If using Chamberlain® technology with a YELLOW LEARN

button, see *ADDITIONAL INSTRUCTIONS. If you are NOT using Chamberlain® technology with a

YELLOW LEARN button, programming for this button is complete.

AVAILABLE PROGRAM METHOD

QUICK START

METHOD

LEARN METHOD

Brand Name

Megahertz

(MHz)

Specification Notes

Pre-set Button

Number on

Remote

Number of

Button Presses

*Chamberlain®®

390

Security +®, Orange/Red Learn Button

*Chamberlain®®

315

Security +®, Purple Learn Button

*Chamberlain®®

390

Billion Code®, Green Learn Button

*Chamberlain®®

390

Security + 2.0®, Yellow Learn Button

*Chamberlain®®

390

Fixed Dip Switch

FAAC®

433.92

Rolling

Genie®

315/390

Intellicode® I

Genie®

315/390

Intellicode® II

Genie®

390

Fixed Dip Switch

Guardian®

303

Xtreme® brand

Linear®

318

MegaCode®

Marantec®

315

Fixed Learn

NICE®

433.92

Rolling

Overhead Door® 315/390

CodeDodger® I

Overhead Door® 315/390

CodeDodger® II

Overhead Door® 390

Fixed Dip Switch

Ryobi®

372.5

Rolling

Sommer®

310

Rolling

Stanley®

310

Fixed Dip Switch

Wayne Dalton®

372.5

Rolling

Xtreme® brand

303

Fixed Learn

FACTORY DEFAULT: If at any time the remote needs to be cleared and returned to its factory default

settings, press and hold down button #3 while pressing button #4 - four times. The blue LED will give

a long blink and then go out. This will clear any existing programming and return the remote to its

original factory default settings.

PROGRAMMING ASSISTANCE: If the opener does not activate after the steps shown, repeat steps or

contact Customer Care by website chat (www.geniecompany.com) or by phone at:

1-800-354-3643 for programming assistance.

Chart A

PARTS

Visor Clip

Dock

Key Chain

*Genie and Intellicode are registered trademarks of The Genie Company. All other listed names

and trademarks are the property of their respective owners.

* ADDITIONAL INSTRUCTIONS:

For use with Chamberlain® technology with a YELLOW LEARN button: At this time, the opener should have

just activated and then stopped. When it stops, press the YELLOW LEARN button on the

garage door opener again for 2-3 seconds and then release. Press the #2 pre-set button again one time or

until the opener activates. Let the opener run until it stops. Programming for this button is complete.

Changing the Battery:

Remove small phillips head backing screw.

Pry case open with small coin or screwdriver.

Replace battery with CR2032 coin cell.