TECHBOY INTERNATIONAL LIMITED TB001 ユーザーズマニュアル

Power switch:

Finger Holder

Short press to turn

off Quadcopter
Long press to turn 

off controller

Five directions switch

7

8

Length:120mm,width:120mm,height:45mm.

Product:1x3.7V-200mAh battery,inst-alled inside of  produ-

ct,it is replaceable. 
Controller:3xAAA battery required.1.5V,it is replaceable,not 

included.

Charging time:about 30 minutes.Working time:about 5-8 

minutes.Control distance:20m.

TB-820 Quadcopter 1Pcs,Controller 1 Pcs,Instruction Manual

1 Pcs,Finger holder 2 Pcs.USB cable 1 Pcs.

Please keep it far away from direct sunlight or heat.The Q-

uadcopter & controler contain electrical parts.Please keep it 

far way from water or wet environment.Please use dry clean 

cloth to clean product if it is getdirty.Do not wash it.

Take battery out from box.Disassemble battery from PCB 

wire cable(refer picture 3).Connect battery cable to USB co-

nnector (refer picture 4).insert the USB port of the USB ch-

arging wire to the USB port of thecomputer(or the USB port

of the power adapter)to charge the battery.USB cable red li-

ght turn on it indicate it is charging.When USB cable red lig-

ht turn off.It indicates fully charged.Disassemble USB cable 

and battery.Install battery into box.

2.Lean forward/backwsard/left/right slowly (with angle over 15)

controller.To control copter fly forward/backward/left/right (ref-

er picture 4)

3.press to K3 direction,move hand to left or right, the copter tu-

rn left orright.(refer picture 5)

4.press to K1 direction, adjust speed press once to medium spe-

ed.Presscnce again to high speed.Press third time to low speed 

(copter keep inlow speed at very beginning)(refer picture 6)

5.Fly higher/lower,press K4 and at same time move your wrist 

up anddown slowly,the copter fly higher or lower altitude,r-

elease K4,copter keep in current altitude,hovering.(refer pict-

ure7)

6.Landing,press K button,the copter stop flying and begin to

 landing slowly.
7.Stop immedicately in case emgerency. Press turn on/off butt-

on againto trun off copter immedicately if any emgerency or 

copter could not landing successfully or propellers keep rot-

ating.

NOTE:The flying unit contains a Lithium Polymer Bat-

tery,DO NOT disassembly the flying unit as this may 

result in permanent damage or hazardous operation.

DO NOT mix old and new batteries.

DO NOT mix alkaline.Carbon-zinc or rechargeable (-

               nikel-cadium)batteries.

DO NOT try to charge non-rechargeable batteries.

DO NOT dispose of batteries in fire.

DO NOT short circuit the supply terminals.

DO NOT use near water.Ensure that the contact surf-

aces are clean before installing new batteries.Batteries 

should always be replaced by adults.Replace batteries 

of the same type and brand at the same time.

DO NOT modify this product in any way.

DO NOT laumch at people or animals.

DO NOT use near overhead cables,vents,fans or any 

other obstacles.

ADULT SUPERVISION IS RECOMMENDED AT ALL TI-

MES!

DO NOT attempt to retrieve yourself.

☆

Make sure people around you are aware you are 

playing.

☆

If the quadcopter gets stuck in high places,ask an 

adult to retrieve it for you.

☆

Before recharging,when not in use or before stor-

age,always allowyour quadcopter to deplete its 

charge (by allowing the propeller to spin freely u-

ntil it stops),and switch OFF when not in use.

☆

Only use the charger provided in this pack to ch-

arge quadcopter and only under adult supervition.

1.Make sure flying height is over 2 meters and copter is in full 

chargedstatus when do stunt operation.

2.Press K2, Lean rightward/leftward/forward/backward(with a-

ngle over75)controller. To control copter do leftward/rightward/

forward/backward stunt operation.(refer picture 8)

The packaging box and instruction manual contains important 

information,please keep it for further reference.

1.Use screwdriver or other objects,press the battery cover b-

utton.andtake off battery cover at same time.(refer picture 3).

2.Install 3 x AAA batteries according battery polarity.(refer p-

icture 4)

3.re-install battery cover.it install well when you hear “DA”

sound.

4.Remove batteries according above steps.

1.Connect the battery to copter correctly , put the copter on 

the flat groud(The copter's battery in front of you) the light 

flashing from high speed to low speed. 

2.Install batteries into controller correctly.

3.Press ON/OFF transparent button of controller.(refer pict-

ure 1)DroneLED turn to keep lighting,indicate code match s-

uccessfully,Repressbutton if failed.

4.Please replace new batteries if controller LED do not light.

1.Press K, the copter take off automatically,and keep in 

a certain height hovering.(refer picture 3)

1.Connect battery wire to PCB wire cable (referpicture1.)Put 

battery into box.(refer picture 2)

2.Refer above instruction to take out battery

INSTRUCTION MANUAL

Circuit board cable

Battery compartments

The battery cable

Battery

3

3.7V-200mAh

   USB

Battery 

3.7V-200mAh

K Auto take off/landing (please 

refer operation details)
K1 Speed adjustment (please re

fer operation details)
K2 Stunt (please refer operation 

details)

K3 Turning (please refer operation 

details)
K4 Height adjustment (please refer 

operation details)

Motion controlled flying objects