VECTRIX CORPORATION GC667894 ユーザーズマニュアル
Transmitter (Digimatic) Operations Manual
2015.11
TelemeasureII Transmitter transmits measured data
received from digital measuring devices by FM radio wave.
１．
Caution
1) Avoid to use at the following places:
Place with much dust, direct sunshine, high temperature,
possibility of stain by acid/alkaline/organic solution or water/oil,
strong electromagnetic shield, strong electromagnetic wave, spark
by arc welder or electrical discharge machine、strong radio wave
near by high voltage electric wire or radio station
possibility of stain by acid/alkaline/organic solution or water/oil,
strong electromagnetic shield, strong electromagnetic wave, spark
by arc welder or electrical discharge machine、strong radio wave
near by high voltage electric wire or radio station
2) Do not add a shock by excessive power or drop.
３
３
) Do not use organic solvent such as thinner. Please wipe off
the dirt with dry cloth, neutral detergent or alcohol lightly.
4) Never take it apart!
5) Do not add excessive power to cable to avoid the breaking.
5) Do not add excessive power to cable to avoid the breaking.
２
. FCC Warning
Changes or modifications not expressly by the party
responsible for compliance could void the user’s authority to
operate the equipment.
operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
(1) this device may not cause harmful interference,
and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: 2AM9D GC667894
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician
for help. This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and
receiver.
--Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician
for help. This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and meets
the FCC radio frequency(RF)Exposure Guidelines
in Supplement C to OET65. This equipment has very low
levels of RF energy that are deemed to comply without
testing of specific absorption ratio(SAR).
limits set forth for an uncontrolled environment and meets
the FCC radio frequency(RF)Exposure Guidelines
in Supplement C to OET65. This equipment has very low
levels of RF energy that are deemed to comply without
testing of specific absorption ratio(SAR).
２．
Name and Function
①ＤＡＴＡ
Transmission Switch *
1
(DATA Sw.)
Wireless data transmission shown
on LCD of measuring equipment
②
on LCD of measuring equipment
②
IＤ No. Setting Switch(ID Sw.)
Whole number on the LCD is set as
ID No.
ID No.
（
Details are mentioned later.）
③
CANCEL Switch (C Sw.)
While pushing this switch 、 when push Ｄ Ａ Ｔ Ａ Sw., it
transmits cancel signal for latest data.
transmits cancel signal for latest data.
*1 For external switch type (TXG-xxQ) here is DATA transmission
cab
le. Connect hand switch or foot switch, then push its
transmission button.
３．
Operations
３．１
Battery (CR2032 ; Nominal voltage:3.0V) exchange
１
) Insert the flat blade screwdriver to the side of the battery
cover. Remove the battery cover so as to spread it outward.
Insert the flat blade screwdriver to the lower
side of battery holder、then remove the used
battery.
Upper side
Lower side
Insert a new coin lithium battery
(CR2032) from upper side of battery holder.
Notice: Please pay attention to the polarity
of battery.
of battery.
Plus(+mark);face
Minus;back
２
) Mount the battery cover.
*2 Implemented battery at shipping is monitoring use.
It may not satisfy the life of battery.
3.2
Connection with the measuring equipment
Transmitter itself does not function.
Connect with interface of digimatic measuring equipment.
３．３
ID No. setting
For wireless data input, ID No. of transmitter and ID No.
setting at QCPRO/QCPROEX installed in PC must be same.
Telemeasure has ID No. setting function where user can set
any integer from 0～99 as ID No.
ID No. setting of transmitter is as follows:
ID No. setting of transmitter is as follows:
*3
About ID No. setting at PC side, look at operations
manual of QCPRO or QCPROEX.
１）
Confirm numeric on LCD of measuring equipment.
２）
Let measuring equipment show ID No. you want to set.
The decimal number does not matter.
The decimal number does not matter.
３）
Push IＤ Sw. then buzzer sounds “Pi”.
The integral part is set as ID No.
(X: any number)
Display on ＬＣＤ
ＩＤ
No.
0．XX ｍｍ
0
1．XX ｍｍ
1
12．XX ｍｍ
１２