Cellnovo Ltd 1001055 ユーザーズマニュアル
Cellnovo OTS Handset
Model No.: 1001055
Designed in San Francisco.
Assembled in China.
©All Rights Resevrved.
www.cellnovo.com
Cellnovo Ltd
Pencoed Technology Centre
Pencoed
UK
CF35 5HZ
+44 (0) 2030 581260
Safety & Precautions
•this device is in compliance with the essential
requirements and other relevant provisions of
Directive 2014/53/EU
To prevent any damage to the device or any injury
to you, please read the safety information before
using the device:
• Do not use the device with wet hands.
• Do not use damaged power cords
• Never try to pull the charger from the cord.
• Avoid using any non-Cellnovo chargers.
• Keep the device dry. Precipitation, humidity, liquids
• Do not use the device with wet hands.
• Do not use damaged power cords
• Never try to pull the charger from the cord.
• Avoid using any non-Cellnovo chargers.
• Keep the device dry. Precipitation, humidity, liquids
or moisture can contain minerals that will corrode
the electronic circuits. If your device does get wet,
allow the device to dry completely before using it. In
case of any issues, contact Cellnovo.
• Do not use or store the device in dusty, dirty areas.
• Do not store the device in extreme heat or cold
• Do not use or store the device in dusty, dirty areas.
• Do not store the device in extreme heat or cold
temperature. High or cold temperatures can shorten
the life of electronic devices and damage batteries.
• Do not attempt to open the device other than as
• Do not attempt to open the device other than as
instructed in this guide.
• Do not drop, knock, or shake the device.
• Do not drop, knock, or shake the device.
Rough handling can break internal circuit boards and
fine mechanics.
• Do not use harsh chemicals, cleaning solvents, or
• Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the device. Only use a soft,
clean, dry cloth to clean the surface of the device.
02
03
04
05
06
07
10
09
12
13
Traffic Safety
Avoid using handset while driving, please
follow the traffic rules. Please follow all
safety warnings and regulations when using
your device in restricted areas.
Do not use, if using device is prohibited.
Do not use the device if doing so causes
danger or interference with other electronic
equipment.
Near Sensitive Electronics
Your handset may cause interference when
used near TVs, radios or automated office
equipment.
While Flying
Your handset can cause interference with
aircraft equipment. Please follow all airline
and crew regulations and power off your
handset or select Airplane Mode when
directed.
In Medical Facilities
Your handset may interfere with the
normal operation of a medical equipment.
Follow all hospital regulations and power
off your handset or select Airplane Mode
when directed.
At a Fuel Station
It is not advisable to use your handset at
fuel stations.
Disassembled Product
Never take your handset apart.
Unauthorized repairs could break the terms
of your warranty
Around Children
Keep your handset out of children’s reach. It
should never be used as a toy.
Original Accessories
Only use the original accessories supplied
with your handset or those approved by the
manufacturer.
Near Explosives
Turn off your handset in or near
areas where inflammable or explosive
materials are stored or used.
Working Temperature
The working temperature for the handset
is between 0º and 40ºC. Using the device
outside of this range may cause malfunction
and lead to long-term damage.
Safe Volume levels
Prolonged exposure to high volume levels
through your handset or ear phones
can damage your hearing. Exposure to
high volumes while driving may cause
distraction and increase your risk of an
accident.
Specific Absorption Rate (SAR) Information
Your handset is a radio transmitter and receiver. It
has been designed to comply with applicable safety
requirements for exposure to radio waves. The
radio wave exposure guidelines employ a unit of
measurement called Specific Absorption Rate (SAR).
Te recommended SAR limit for any handset is 1.6
Te recommended SAR limit for any handset is 1.6
W/Kg averaged over a 6 minute period and taken
over a volume containing a mass 1g of human tissue.
Body-worn Operation:
Body-worn Operation:
This device was tested for typical body-worn
operations. To comply with RF exposure
requirements, a minimum separation distance of
10 mm must be maintained between the user’s body
and the handset, including the antenna. Third-party
belt-clips, holsters, and similar accessories used
by this device should not contain any metallic
components. Body-worn accessories that do not
meet these requirements may not comply with RF
exposure requirements and should be avoided. Use
only the supplied or an approved antenna.
Maximum SAR for this device is as mentioned:
Head SAR: 0.435 Watt/Kg @ 1gm
Body worn SAR: 1.455 Watt/Kg @ 1gm
Body-worn distance: 10mm
Before you get started, please read below:
Charge the battery
Before using the device you will need to fully charge
the handset with the charging accessories provided
with the handset. The battery is non-removable;
attempting to remove it may invalidate your warranty.
Limitation of damages
To the maximum extent permitted by applicable law,
in no event shall Cellnovo or its affiliates be liable to
you, any user, or third party for any indirect, special,
consequential, incidental or punitive damages of
any kind, arising in contract, tort, or otherwise,
including, but not limited to, injury, loss of revenue,
loss of goodwill, loss of business opportunity, loss of
data, and/or loss of profits, regardless of the foresee-
ability thereof or whether Cellnovo or its affiliates
have been advised of the possibility of such damages.
And in no event shall the total liability of Cellnovo
or its affiliates exceed the amount received from you,
regardless of the legal theory under which the cause
of action is brought.
The foregoing does not affect any statutory rights
The foregoing does not affect any statutory rights
which may not be disclaimed.
Disclaimer
Thank you for choosing to use Cellnovo. This
device is built to provide you with a high quality
handset. Please read this guide carefully and keep
it for future use.
• The content and pictures in this manual may differ
• The content and pictures in this manual may differ
from the product, or from the software provided
by service providers or carriers, and are subject to
change without prior notice.
• The items supplied with your device and available
accessories may vary depending on your region or
service provider.
• Other accessories may not be compatible with
• Other accessories may not be compatible with
your device; likewise the supplied items are designed
only for your device and may be incompatible with
other devices.
Device Overview,
Layout & Labeling
Power Button
Main ANT
SIM Tray
BT/WIFI ANT
Micro USB connector
Secondary ANT
Display
Power On/Off
Power On
Press the power button until your phone vibrates.
When you turn on the device for the first time, you
will need to set it up.
Power Off
1. If the display is off, press the power button to
turn it back on.
2. Press and hold the power button for a few seconds
2. Press and hold the power button for a few seconds
and tap on power off on the options menu.
SIM Card
The SIM card will already be installed in your
handset. Do not change this SIM card as it will
invalidate the system and will affect your warranty.
Environmental Compliances
As per rules laid down by government for
environmental concerns and safety, your device has
been made to comply and conform to the respective
regulations below:
The product is in conformity with the requirements
The product is in conformity with the requirements
of Rule 13 of e-waste Rules. The content of hazardous
substance with the exemption of the applications
listed in SCHEDULE II of the e-waste Rules:
1. Lead (Pb) – not over 0.1% by weight;
2. Cadmium (Cd) – not over 0.01% by weight;
3. Mercury (Hg) – not over 0.1% by weight;
4. Hexavalent chromium (Cr6+) – not over 0.1%
by weight;
5. Polybrominated biphenyls (PBBs) – not over
0.1% by weight;
6. Polybrominated diphenyl ethers (PBDEs) –
1. Lead (Pb) – not over 0.1% by weight;
2. Cadmium (Cd) – not over 0.01% by weight;
3. Mercury (Hg) – not over 0.1% by weight;
4. Hexavalent chromium (Cr6+) – not over 0.1%
by weight;
5. Polybrominated biphenyls (PBBs) – not over
0.1% by weight;
6. Polybrominated diphenyl ethers (PBDEs) –
not over 0.1% by weight.
1
5
4
3
2
7
6
Cellnovo QSG
Prepared by Cellnovo
Black 100%
Pantone 294C
Pantone Cool Gray 8
85 mm
10
R
40 mm
Quick Start Guide
For detailed user manual and specifications please log
on to http://www.cellnovo.com
Proper Disposal
This symbol (with or without a solid
bar) on the device, batteries, and/or the
packaging, indicates that the device and
its electrical accessories and batteries
should not be disposed of as household
waste. These items should be taken to a
certified collection point for recycling or
proper disposal.
For the purpose of recycling to facilitate
effective utilization of resources,
please return this product to a nearby
authorized collection centre, registered
dismantler or recycler, or Cellnovo when
disposing of this product.
Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference received,
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
No changes shall be made to the equipment without
No changes shall be made to the equipment without
the manufacturer’s permission as this may void the
user’s authority to operate the equipment.
14
15
Information to the user.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference
by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment
-Increase the separation between the equipment
and receiver.
-Connect the equipment into an outlet on a circuit
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
-Consult the dealer or an experienced radio/TV
technician for help
Some content may differ from your device depending
on the region, service provider, or software version
and is subject to change without prior notice.
Android is a trademark of Google Inc.
Android is a trademark of Google Inc.
All trademarks, logos, mark symbols and other
details mentioned here are trade names, trademarks
or service marks of their perspective owners.
Cellnovo holds no responsibility of the partner
logos and content. All images are for representation
purposes only.
Manufactured under license from Dolby
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio and the double-D
symbol are trademarks of Dolby Laboratories.
ISED (IC)
(en)
This device complies with Industry Canada’s licence-
This device complies with Industry Canada’s licence-
exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference,
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
(fr)
Le présent appareil est conforme aux CNR
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le
brouillage est susceptible d’en compromettre le
fonctionnement.
08
11