iMageTech Co. Ltd IMAGEA2SPK01 ユーザーズマニュアル

1. Increase volume

2. Lower volume

3. Mute

4: Mute microphone

5: Answer

6: Hang up

7: Mode selection

8: Mode status 

indicator

9: Power status 

indicator

Bluetooth Mode

USB Mode

AUX Mode

Adapter Mode

LED Indicator

Power status/Charging

10: Audio In

11. USB Slot

12. Power switch

AUX IN

Charing First

!

Please connect the USB cable to iMage A2 Bluetooth Conference Spea-

kerphone to charge it; it is recommended to fully charge the power for 

approximately 6 hours (charge until     power indicator goes off) before 

using it for the first time. 

Power Status

When the power is turned on, if one of the four mode indicators on the 

right has a blue light on, it means that the unit is currently powered-on.

Charging: When the orange     light is constantly on, it means that it is 

currently charging; when the orange light goes off, it means 

that charging is complete.

Power remaining: If the blue      light flickers it means

 

that there is 

sufficient power remaining; if the red      light flickers it 

means that power is low and requires charging.

Packing

1. iMage A2 Bluetooth Conference Speakerphone

2. Micro-USB cable

3. User manual

Mode selection: Bluetooth Mode

You can connect other portable devices or computer using 

Bluetooth connection to make iMage A2 Bluetooth Conference 

Speakerphone your multimedia speakerphone.
Connection method:

1. Select “Search for Bluetooth device” on the device you want to 

connect.

2. You will see “iMage A2_XX (number differs according to the 

different devices)”; click on it to perform pairing.

3. Pairing complete. 

Blue light remains constantly on: Bluetooth device has successfully 

connected with iMage A2 Bluetooth Conference Speakerphone, and 

supports HFP and A2DP.
* If the device could not be paired, you can clear the previous 

pairing data to pair it over again; press and hold         the hang up 

button for 3 seconds and wait until you hear the prompt then 

release it to search for iMage A2 Bluetooth Conference 

Speakerphone again for pairing.

* Please confirm the Bluetooth chip built in the computer before 

connecting to a PC or notebook using Bluetooth Mode, and 

download the related driver programs etc. from the original 

manufacturer of the chip; please refer to the user manual of your 

computer for details. 

   Dimensions: 165mm X 165mm X 55mm

   Product weight: 360±5g

   Bluetooth version: Bluetooth v3.0+EDR/HFP/A2DP/WBS

   Communication time: 6~8 hr.(BT)

   Playback time: 6~8 hr.(BT), 8~10 hr.(AUX)

   Standby time: 48~60 hr.(BT)

   Battery capacity: 950mAH

   Reception angle: Omni-Directional

   Operating frequency: 2402MHz-2480MHz

   Reception distance: 0.3~3m

   Audio output: Bluetooth/USB

   Audio input: Bluetooth/USB/AUX

   Module type: GFSK

   Antenna type: Build-in Antenna

   Operating environment: 0 ~ 70

℃

* Note: Data listed above were measured by actual testing in laboratories; 

actual data may differ according to usage scenarios.

iMage A2 Bluetooth Conference Speakerphone

I/O Port buttons and slots

Welcome!

Thank you for purchasing iMage A2 Bluetooth Conference 

Speakerphone; this instruction manual will guide you on how to start 

using this product.

Start

Turn on the power and start iMage A2 Bluetooth Conference 

Speakerphone; press the          (mode selection) button to select the 

mode you need.

Note: The battery life will significantly decrease if your device has not 

been charged for a lone time.Therefore, we recommend you to charge 

your device at least once every week

.

Specification

Mode selection: AUX Mode

You can make iMage A2 Bluetooth Conference Speakerphone an 

expansion speaker by connecting it to a signal source using a 3.5Ø 

audio cable. 

Connection method: Connect the audio output of the device (PC, NB 

etc.) to the Audio In socket(3.5Ø jack) of iMage A2 Bluetooth 

Conference Speakerphone.