IDEM INC. L1R ユーザーズマニュアル

Do not place ringing 

alarm or activate alarm 

near ears.

7

Handle Bar Mount

For more information and support on this product, please 
visit our website.

This product is covered by a warranty for a period of one 
(1) year from the date of original purchase. For more 
information, please visit our product website.

All resgistered logos and trademarks property of the respective owners.

Attach adhesive pad to the bottom of mounting 

bracket.

Insert cable ties through the mounting bracket.

Place the bracket with adhesive pad over the handle 

bar. Pull cable ties tightly to secure the remote in 

place. Trim excessive cable ties if needed. 

Press to cycle through different “Flash”  modes (same 
function as remote FLASH button).

When there is a malfunction between Taillight and 
remote control, press for 2 seconds and Taillight will 
sound an ALERT. Press any key on the remote control, 
and Taillight will sound an ALERT 2 times confirming the 
completion of pairing. 

When the remote control is lost, contact customer 
support.

sec.

1
2
3
4

Burst Flash
Fast Flash
Slow Flash
Taillight is off

3
2
1
0

Mode

Pattern

Flash/Sec.

8

6

OPTION 2: Seat Post Mount

Secure seat post mounting bracket with supplied 

MED Hex Bolt and LG Hex Tool.

Slide Taillight onto mounting bracket. Secure 

Taillight to the bracket with a supplied SM Hex Bolt 

and SM Hex Tool.

5

OPTION 1: Saddle Mount

Slide open saddle mounting bracket.

Position bracket under bike saddle.

Brackets may also be installed upside down. 

Tighten bracket with supplied LG Hex Bolt and 

LG Hex Tool.

Slide Taillight onto mounting bracket. Secure 

Taillight to the bracket with a supplied SM Hex Bolt 

and SM Hex Tool.

2

1

(Optional)

When Taillight is not in 
“LOCK” mode, press 
“FLASH” button to cycle 
through each of the 
“FLASH” Modes.
 

3

4

Press “LOCK” button once, Taillight will sound 
an ALERT 3 times. Taillight is now armed and 
you will hear another ALERT sound after 3 
seconds. If distrubed afterwards, the alarm will 
sound.

Press “UNLOCK” button once and a single long 
ALERT will sound. This signals the exit of 
“LOCK” mode.

Press and release 
“HORN” button to receive 
3 short horn tones. Press 
and hold the button to 
receive 3 short and a long 
horn tones.

When in “LOCK” mode and motion is detected, 
Taillight will generate a loud ALARM briefly. If 
motion is detected again within the next 10 
seconds, an ALARM will sound nonstop for 30 
seconds, and then return to “LOCK” mode.

or

Press the release  

hook and remove 

the remote control 

to access remote

buttons.

When Taillight is charging, the light will turn on. When it is 

fully charged, the light will turn off.

Connect Taillight to your computer or external power bank 

with cable provided.

Quick Start Guide

Wireless / Multifunction

1R

PATNEON COOL GRAY 10

PATNEON 376

DIELINE

75mm

75mm

75mm

75mm

75mm

156mm

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the 

    following two conditions:

    • This device may not cause harmful interference.

    • This device must accept any interference received, including interference that 

      may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for 

    compliance could void the user’s authority to operate the equipment. 

Note:This equipment has been tested and found to comply with the limits for a 

class B digital device,pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a 

residential installation.

This equipment generates uses and can radiate radio frequence energy and,if 

not installed and used in accordance with the instructions,may cause harmful 

interference to radio communications.However,there is no guarantee that 

interference will not accor in a particular installation.if this equipmemt does 

cause harmful interference to radio or television reception,which can be 

determined by turning the equipment off and on,the user is encouraged to try to 

correct the interference by one or more of the following measures: 

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an autlet on a circuit different from that to which 

  the receiver is connectec.

• Consult the dealer or an experienced radio/TV technician for help.