Apex Drone Co. Ltd. GD90C-RD ユーザーズマニュアル
3
5
4
6
8
11
User Manual
NO.GD-90C
9
10
Standard components
Name of components
1xDrone
1x Controller
Controller instruction
Battery Installation
Calibration between drone and controller
On a flat surface
Schematic diagram
of drone power connection
Controller’s function
Correct operations of drone
Flip operations of drone
Charging
The application of App
APP download and installation
AT96_XXXXXX
GD145_XXXXXX
2.The Wifi connection
The name of wifi
Connected
(1) please open your drone first and connect your mobile WIFI hotspot to
AT96_XXXXXX ".
(2)Enter the APP. If the mobile APP is successfully connected to the drone,
you can see real-time image transmission in the APP.
It can be controlled remotely by a mobile phone.
(3) The remote control is invalid when the mobile phone controls the drone;
Mobile phone control is invalid when the remote control controls the drone.
Operating instructions of APP
1.After installing the APP on the phone, click enter and the following screen appears.
Push the throttle lever up ,
drone will fly up.
drone will fly up.
Push the throttle lever down,
drone will fly down.
drone will fly down.
Push the throttle lever to left,
drone will turn left.
drone will turn left.
Push the throttle lever to right,
drone will turn right.
drone will turn right.
Descent
Ascent
Turn right
Throttle
(Top position)
Throttle(zero position)
Spin around
Turn left
Push the direction lever up,
drone will fly forward.
drone will fly forward.
Push the direction lever down,
drone will fly backward.
drone will fly backward.
Push the direction lever left,
drone will fly to left.
drone will fly to left.
Push the direction lever right ,
drone will fly right.
drone will fly right.
Right
Left
Left/Right
Fly backward
Flight forward
and backward
and backward
Fly forward
backward
F
R
F
R
Replace blades
To achieve optimal flight function, the blades need to be checked or replaced after
multiple flights.Emergency landings, especially from high altitude will damage
blades.
1. When replacing the blades, please make sure that the letters on the blades (F is the
forward rotating blades,R is the reverse blades, letters are on the back of the blades).
2. Pay special attention to replacing damaged blades with properly blades.Must not
change the wrong direction of the blades!
multiple flights.Emergency landings, especially from high altitude will damage
blades.
1. When replacing the blades, please make sure that the letters on the blades (F is the
forward rotating blades,R is the reverse blades, letters are on the back of the blades).
2. Pay special attention to replacing damaged blades with properly blades.Must not
change the wrong direction of the blades!
F=front left positive blades
R=front right reverse blades
R=back left positive blades
F=back right positive blades
forward
Download the APP according to your mobile phone system model, as follows:
1. Android System
A: Search for the keyword 'AT-96' in Baidu mobile assistant APP
(Android market or 91 Assistant) to download.
Or use a browser to scan a QR code to download
If scan code download fail, please download in Baidu mobile assistant APP
B: on Google play: search for the keyword 'AT-96' to download
A: Search for the keyword 'AT-96' in Baidu mobile assistant APP
(Android market or 91 Assistant) to download.
Or use a browser to scan a QR code to download
If scan code download fail, please download in Baidu mobile assistant APP
B: on Google play: search for the keyword 'AT-96' to download
2.For IOS system
Please go to App store, enter the key word "AT-96" to download the app.
Please go to App store, enter the key word "AT-96" to download the app.
Direction lever
Throttle lever
Take photo
Take video
Album
Settings
One key to
take off
take off
One key
to return
Trim
Speed
One key
to land
to land
Lever throttle
G-sensor
WIFI state
Power state
<8
Headless
mode
mode
3. Throttle lever
Turn on the Throttle lever, and the drone indicator light will be always on. At this time,
you can fly through the virtual handle.
4.Please refer to P4 for throttle and direction control .
5. Take pictures
Trigger the APP photo function;
Short press the remote control also can take photos.
6.Camera shooting
Trigger the APP camera shooting function, the camera shooting starts, and trigger
the camera again,it will stop camera shooting.
Long press the remote control camera function can also be used for camera
shooting.
7. Gravity induction
Trigger the gravity sensor, which controls the drone's direction by sensing the earth's
gravity through the phone's built-in sensor chip.
8. WIFI state
This icon displays the signal strength of the drone connected to the remote control.
9. Photo album
Click on this to view the photos and recorded video you take.
10.Gesture Photograpy
Click the setting button in the lower right corner of the screen,then turn on the thumb
automatic camera switch and return to image interface.A rectangle frame will
appear in the middle of the screen.Then put your thumb and place it in the frame
and it will automatically take photos after countdown 3 seconds.
(The best working range of gesture photography is 0.5-3 meters).
Turn on the Throttle lever, and the drone indicator light will be always on. At this time,
you can fly through the virtual handle.
4.Please refer to P4 for throttle and direction control .
5. Take pictures
Trigger the APP photo function;
Short press the remote control also can take photos.
6.Camera shooting
Trigger the APP camera shooting function, the camera shooting starts, and trigger
the camera again,it will stop camera shooting.
Long press the remote control camera function can also be used for camera
shooting.
7. Gravity induction
Trigger the gravity sensor, which controls the drone's direction by sensing the earth's
gravity through the phone's built-in sensor chip.
8. WIFI state
This icon displays the signal strength of the drone connected to the remote control.
9. Photo album
Click on this to view the photos and recorded video you take.
10.Gesture Photograpy
Click the setting button in the lower right corner of the screen,then turn on the thumb
automatic camera switch and return to image interface.A rectangle frame will
appear in the middle of the screen.Then put your thumb and place it in the frame
and it will automatically take photos after countdown 3 seconds.
(The best working range of gesture photography is 0.5-3 meters).
Caution
Before you fly the drone, please do some simulated flight practice.
S tep t wo
S tep one
WARNING
4x Blades
1x User manual
1x USB Charger
1x Screw driver
Li-Po Battery
1x Mobile phone plastic holder
battery type
Lithium batteries
battery specification
using time
drone flight time :6-8mins
charging time
about 50
mins(charging
current approx 0.5A)
mins(charging
current approx 0.5A)
3.7V 400 mAh
Battery and charge specification
light on
light blink
charging
Ready mode
light off
charge
completed
input
charging current
full voltage
LED indicator
Charging specification
Notice
5V
420-450 mA
4.2V
0.05V
+
_
Problem shooting
Troubles
Causes
1
2
3
4
5
6
Turn on the drone ,LED blinks ,
while the drone has no
responding to all commands
while the drone has no
responding to all commands
Pair between drone and controller
failed
failed
(please refer to the frequency
alignment of remote controller and
receiver in P3)
alignment of remote controller and
receiver in P3)
The battery died
Charge the drone
Put the throttle lever to zero
position
position
1.Change the blades
2.Charge the drone
2.Charge the drone
1.Install the blades
2.Replace the blades
3.Refer to p3 for calibration
2.Replace the blades
3.Refer to p3 for calibration
1.Tighten the blades
2.Replace the blades
2.Replace the blades
Throttle lever is not at the zero
position
position
1.Blades may installed wrong
2.No enough power
2.No enough power
1.Blades may installed wrong
2.Blades get damaged
3.Calibration failed
2.Blades get damaged
3.Calibration failed
1.Blades are getting lose
2.Blades get damaged
2.Blades get damaged
Turn on the drone ,the drone
has no reaction to the
commands
has no reaction to the
commands
Blades keep moving after
landing
landing
Blades keep moving ,while
the drone can not take off
the drone can not take off
After trimming ,drone keeps
spin,and the speed of blades is
different
spin,and the speed of blades is
different
The drone can not take off after
drop
drop
Solutions
FCC Statement
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. T hese limits are designed to provide reasonable
protection against harmful interference in a re sidential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or televisi on reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit di fferent from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interf erence that may cause undesired operation.
Changes or modifications not expressly approv ed by the party responsible for compliance
could void the user's authority to operate the equipment.
Front flip:move direction
lever forward.
lever forward.
Back flip:move direction
lever backward.
lever backward.
Left/Right flip:move the
direction lever left/right.
direction lever left/right.
Press the “Flip” button,
the controller will beep.
the controller will beep.
Press the “Flip” button,
the controller will beep.
the controller will beep.
Left flip
Right flip
Front flip
Back flip
7.Stable flight, flexible, easy realize 3D flip
7
Camera
Camera board
Positive rotor blades
Reverse rotor blades
Upper body
Protected shell
Bottom shell
Positive rotor
Reverse rotor
Lithium battery
Receiver board
Battery charge
Mobile phone adapter
φ Output: 5V
Charging current: 1-2A.
.
Cautions:
1.Be sure to check your surroundings before flying.
2. Do not let the drone fly out of sight while flying.
3. Children cannot fly alone. Please fly with adults.
4. Please confirm that there is no other product using the same frequency band in the same area.
1.Be sure to check your surroundings before flying.
2. Do not let the drone fly out of sight while flying.
3. Children cannot fly alone. Please fly with adults.
4. Please confirm that there is no other product using the same frequency band in the same area.
* The chargers, wires, plugs, shells and other parts shall be checked regularly. If any damage is
found, it shall be discontinued until it is repaired.
found, it shall be discontinued until it is repaired.
* Only use original charger, charger is not toy.
* Please clean the product with a clean and soft cloth. The drone should be disconnected from
the charger before cleaning.
the charger before cleaning.
* Adult supervision is required when charging a rechargeable battery.
A non-rechargeable battery is not rechargeable.
* Do not short circuit, decompose, fall into the air or put into fire.
* For the long time not operate product . Please remove the battery.
* Do not seriously crash or drop the drone and remote controller.
* This packing and instruction manual contains important information about the product. Please
keep it.
keep it.
WARNING
Important statement
Don’t fly the drone in below conditions
Under the Signal tower,
high voltage pole
An amusement places with
too many people
A field of rain and thunder
Near Airport , rail cars
Roads and nearby places
Near trees/rivers
Strong and romantic
environment
1. This product is applicable to teenagers and adults over the age of 14. This remote controlled four-axis
drone has certain difficulties at the early stage of learning.Suggest only fly under the guidance of
someone with operational experience.
drone has certain difficulties at the early stage of learning.Suggest only fly under the guidance of
someone with operational experience.
2. This product is designed with high and new technology in many aspects such as electronics and
machinery. For those with less experience operator, it should be kept away from people during
flight.We are not responsible for any serious personal injury or property loss which may result from
improper operation.
machinery. For those with less experience operator, it should be kept away from people during
flight.We are not responsible for any serious personal injury or property loss which may result from
improper operation.
3. Once the product is sold, we will not assume any safety responsibilities such as accidents occurred
during operation or use.
during operation or use.
4. In case of problems of use, operation and maintenance, you can contact local dealers to provide
technical support or after-sales service.
technical support or after-sales service.
Short press speed switch/long press flip
Short press take photo/long press take video
Headless mode
On/Off
Direction lever
Trim(left/right)
Trim(forward/backward)
Throttle lever
One key return
One key to take off
One key to land
* As shown in the picture,remove the battery cover of
the remote control, according to the battery pole in the
battery box.Install 2pcs of No.7/ AAA batteries correctly
(Additional purchase) and reload the batteries cover
and tighten the screws.
Note:
A. when installing the battery, the positive and negative
poles of the battery must be identified, and the positive
and negative poles of the battery box must be
identified.Please don't install wrong.
B. Do not mix new and old batteries or different types of
batteries.The pool batteries should be taken out in time.
the remote control, according to the battery pole in the
battery box.Install 2pcs of No.7/ AAA batteries correctly
(Additional purchase) and reload the batteries cover
and tighten the screws.
Note:
A. when installing the battery, the positive and negative
poles of the battery must be identified, and the positive
and negative poles of the battery box must be
identified.Please don't install wrong.
B. Do not mix new and old batteries or different types of
batteries.The pool batteries should be taken out in time.
The battery warning
Rechargeable battery:
This drone can use rechargeable lithium batteries.If the battery cannot be recharged
again, dispose of the battery properly according to local treatment regulations.
Remote control battery:
The remote requires 2 "AAA" batteries (not included ).Read the important
battery safety warning below.
●Do not mix with alkali, standard (carbon zinc) and rechargeable batteries (nickel hydrogen).
●Don't mix old and new batteries.
●Prohibits charging non-rechargeable batteries.
●Rechargeable batteries should removed from the remote control (if removable)
before being charged.
●Rechargeable batteries can only be used under adult supervision.
●Batteries shall be disassembled as soon as they are exhausted and must be properly
recovered or disposed in accordance with national or local government decrees and rules.
●Check supply terminals should not short circuit.
●Recommends using the same or the same type of battery.
●Battery shall be installed according to correct polarity (refer to internal specification).
●Don't throw batteries in the fire that could cause a leak or explosion.
This drone can use rechargeable lithium batteries.If the battery cannot be recharged
again, dispose of the battery properly according to local treatment regulations.
Remote control battery:
The remote requires 2 "AAA" batteries (not included ).Read the important
battery safety warning below.
●Do not mix with alkali, standard (carbon zinc) and rechargeable batteries (nickel hydrogen).
●Don't mix old and new batteries.
●Prohibits charging non-rechargeable batteries.
●Rechargeable batteries should removed from the remote control (if removable)
before being charged.
●Rechargeable batteries can only be used under adult supervision.
●Batteries shall be disassembled as soon as they are exhausted and must be properly
recovered or disposed in accordance with national or local government decrees and rules.
●Check supply terminals should not short circuit.
●Recommends using the same or the same type of battery.
●Battery shall be installed according to correct polarity (refer to internal specification).
●Don't throw batteries in the fire that could cause a leak or explosion.
1.On/off
(1)On
Long press "On/Off" button to turn on the controller .
(2) Off
Long press "On/Off" button to turn off the controller .
2.Lock/Unlock
Turn on the controller first ,then turn on the Drone power. When you hear the "beep beep
beep" sounds, the indicator lights always on, it means the code match completed. Push
the throttle lever to left corner, push direction lever to the right corner (push them at the
same time), to start the motor. When the motor starts work, release both lever. Push throttle
lever to the right corner, push the direction lever to the left corner (Push them at the same
time),the motor will be stop.
3.Throttle control
After unlock the controller, push the throttle more than middle ,the drone will take off.Push
the throttle lower than middle ,the drone will decline.Leave the throttle in middle, drone
will hold its altitude.
4.One key take off /One key landing
After unlock the controller, press "One key take off/One key landing" button,drone will
hover
one meter above the ground. Press again, drone will land automatically.
5.Turning(Left/Right)
After the drone lift-off, push the throttle lever to left /right, the drone will turn left/ right .
6.Forward/Backward
After the drone lift-off, push the direction lever to up/down, the drone will fly
forward/backward.
7.Left and right
After the drone lift-off, push the direction lever to left/right, the drone will fly to left/right.
8.Trim
After the drone take off, without move the throttle, if the drone’s direction is moving, press
"trim" button to adjust the direction.
9.Take photo/video
Short press "Take picture/video" button to take photo, long press it to take video. Photos
and videos will save in the app .
10. Short Press to Change Speed
Short press the button to adjust the speed. There has three speed level, when the buzzer
beep comes one sounds, it’s speed level one, drone will move slowly. When the buzzer
beep comes two sounds,it’s speed level two. When the buzzer beep comes three sounds, its
level three, which is the fastest speed level.
11.Headless mode
Start and settings: Short press the headless mode button, the remote control beeps twice,
the drone indicator light flashes slowly, headless mode start.Now the direction of the
drone’s head is the front of headless mode.If there has a crash or flying forward
deviation, please restart to adjust the required direction frequency.
Exit headless mode: Short press the headless mode button again, (the remote control
beeps and the drone indicator light is always on),it is exit headless mode.
In headless mode, no matter which direction the head of the drone turns, the current
position of the remote control is the right and behind of the drone. At this moment, pull
down the joystick it can recall the drone. Push the joystick up, the aircraft can flight far
away.
12.On key to return
When the rear of the drone are aligned with the pilot, after a short press the button, the
drone will automatically return. If offtrack happen during return you can correct the
channel through the left and right joystick.Short press the button again to end the return
trip.Use the back and forth direction joystick also can end the return trip.
(1)On
Long press "On/Off" button to turn on the controller .
(2) Off
Long press "On/Off" button to turn off the controller .
2.Lock/Unlock
Turn on the controller first ,then turn on the Drone power. When you hear the "beep beep
beep" sounds, the indicator lights always on, it means the code match completed. Push
the throttle lever to left corner, push direction lever to the right corner (push them at the
same time), to start the motor. When the motor starts work, release both lever. Push throttle
lever to the right corner, push the direction lever to the left corner (Push them at the same
time),the motor will be stop.
3.Throttle control
After unlock the controller, push the throttle more than middle ,the drone will take off.Push
the throttle lower than middle ,the drone will decline.Leave the throttle in middle, drone
will hold its altitude.
4.One key take off /One key landing
After unlock the controller, press "One key take off/One key landing" button,drone will
hover
one meter above the ground. Press again, drone will land automatically.
5.Turning(Left/Right)
After the drone lift-off, push the throttle lever to left /right, the drone will turn left/ right .
6.Forward/Backward
After the drone lift-off, push the direction lever to up/down, the drone will fly
forward/backward.
7.Left and right
After the drone lift-off, push the direction lever to left/right, the drone will fly to left/right.
8.Trim
After the drone take off, without move the throttle, if the drone’s direction is moving, press
"trim" button to adjust the direction.
9.Take photo/video
Short press "Take picture/video" button to take photo, long press it to take video. Photos
and videos will save in the app .
10. Short Press to Change Speed
Short press the button to adjust the speed. There has three speed level, when the buzzer
beep comes one sounds, it’s speed level one, drone will move slowly. When the buzzer
beep comes two sounds,it’s speed level two. When the buzzer beep comes three sounds, its
level three, which is the fastest speed level.
11.Headless mode
Start and settings: Short press the headless mode button, the remote control beeps twice,
the drone indicator light flashes slowly, headless mode start.Now the direction of the
drone’s head is the front of headless mode.If there has a crash or flying forward
deviation, please restart to adjust the required direction frequency.
Exit headless mode: Short press the headless mode button again, (the remote control
beeps and the drone indicator light is always on),it is exit headless mode.
In headless mode, no matter which direction the head of the drone turns, the current
position of the remote control is the right and behind of the drone. At this moment, pull
down the joystick it can recall the drone. Push the joystick up, the aircraft can flight far
away.
12.On key to return
When the rear of the drone are aligned with the pilot, after a short press the button, the
drone will automatically return. If offtrack happen during return you can correct the
channel through the left and right joystick.Short press the button again to end the return
trip.Use the back and forth direction joystick also can end the return trip.
During the flight, when you hear the "beeps" sounds from the remote control,it
indicates that the Drone's battery voltage is not enough, so the drone should fall
behind to recharge.It need to charge it with the special charger we gave.
indicates that the Drone's battery voltage is not enough, so the drone should fall
behind to recharge.It need to charge it with the special charger we gave.
During the flight, when the remote control indicator lights flicker, it indicates that the
remote control batter y voltage is not enough, please replace the remote control
battery.
remote control batter y voltage is not enough, please replace the remote control
battery.
1. Remove the lithium battery from the drone, insert one end of the charging cable with the USB
port into the phone adapter interface, and then the interface with the plug on the other end is
correctly connected to the battery socket.
2. Plug the charging cable into the USB port of the computer host. The method is the same as
above, and the charging can also be completed.
3. The indicator light is always on under the charging state, and it will automatically crush out
when the battery reaches the full state.
4. When the charging line is inserted into the USB port and lithium battery is not plugged into the
charging line, the indicator light of the charging line flashes is a normal condition.
port into the phone adapter interface, and then the interface with the plug on the other end is
correctly connected to the battery socket.
2. Plug the charging cable into the USB port of the computer host. The method is the same as
above, and the charging can also be completed.
3. The indicator light is always on under the charging state, and it will automatically crush out
when the battery reaches the full state.
4. When the charging line is inserted into the USB port and lithium battery is not plugged into the
charging line, the indicator light of the charging line flashes is a normal condition.
As shown in the picture, push both joystick of the remote control
to the lower right corner at the same time.When the indicator
light of the drone flashes quickly, release the remote control and
wait for the indicator light keep on lighting.The remote control
will comes “beep beep” sounds and the calibration completed.
to the lower right corner at the same time.When the indicator
light of the drone flashes quickly, release the remote control and
wait for the indicator light keep on lighting.The remote control
will comes “beep beep” sounds and the calibration completed.
If long time not used it, please take out the batter y of the remote
control and keep it properly.Note: If not remove the batteries of the
remote control,store it for long time will cause leakage of battery
and damage the remote control, even cause the risk of burning.
control and keep it properly.Note: If not remove the batteries of the
remote control,store it for long time will cause leakage of battery
and damage the remote control, even cause the risk of burning.
First, turn on the switch button of the remote control, and then
switch on the power switch of the drone.Put the tail of the drone
point at you and put it on the horizontal surface.At the same time
the remote control will be comes "beep, beep beep" sounds,it
indicates a successful matching code.
Important note:
switch on the power switch of the drone.Put the tail of the drone
point at you and put it on the horizontal surface.At the same time
the remote control will be comes "beep, beep beep" sounds,it
indicates a successful matching code.
Important note:
The drone turn on/off needs to connect the
battery line and power line.
Because the internal gyros need to
be horizontal calibrated after the drone open, so please must
put it in the horizontal surface place.
put it in the horizontal surface place.
7
Cautions
Cautions
● Confirm again that the screws and blades are firm.
● Verify that the remote controller and drone’s batteries are sufficient.
● Confirm again that the direction of the wind blade is fitting in right position.
● Make sure there are no other people or obstacles in the flying area.
● In order to fly safely, you must first practice the hover, which is the basis of the flight action
(hover: the drone stays in the air and maintains a fixed position).
● Please stand 2 meters behind the drone during practice.
● In order to fly safely, you must first practice the hover, which is the basis of the flight action
(hover: the drone stays in the air and maintains a fixed position).
● Please stand 2 meters behind the drone during practice.
Flight adjustment and notice for beginners
1.Throttle lever practice
2.Direction control practice
Throttle control is in the left hand,push throttle rocker up slowly,
immediately release the rocker, the drone will rise and hold at a
fixed height; Pull the lever slowly down, and release the lever
immediately, and the drone will descend and stay at a fixed
height.Repeat until you are able to control the drone to any height,
and you are stable settle down to the ground.
immediately release the rocker, the drone will rise and hold at a
fixed height; Pull the lever slowly down, and release the lever
immediately, and the drone will descend and stay at a fixed
height.Repeat until you are able to control the drone to any height,
and you are stable settle down to the ground.
1. Practice forward and backward, it’s in the right hand
up and down direction.Keep the drone at a certain
height.Then fly one meter forward slightly,after the
drone stabilized, fly back one meter .And repeat this
practice.
2. Practice left and right side flying,it’s in the right hand
left and right direction.side.The method is the same as
above.
up and down direction.Keep the drone at a certain
height.Then fly one meter forward slightly,after the
drone stabilized, fly back one meter .And repeat this
practice.
2. Practice left and right side flying,it’s in the right hand
left and right direction.side.The method is the same as
above.
3.Rotation practice
As you become familiar with the step 1-3, draw a circle on the
ground and practice within the circle.It can increase your
control accuracy.
As you get more comfortable with the action, you can draw
smaller circles.
ground and practice within the circle.It can increase your
control accuracy.
As you get more comfortable with the action, you can draw
smaller circles.
Caution
4.Precision practice
1. Slowly raise the throttle lever to control the drone to a certain height.
2. Push the throttle lever to the left/right slowly, make the drone
rotate counterclockwise/clockwise slowly.
2. Push the throttle lever to the left/right slowly, make the drone
rotate counterclockwise/clockwise slowly.
When the drone is flying far away, please lower the throttle and land the drone, then walk to
the right astern of the drone for 2 meters and continuing the practice.Or bring it back to the
home position keep practicing.
the right astern of the drone for 2 meters and continuing the practice.Or bring it back to the
home position keep practicing.
5.Change the direction of drone
When you feel familiar with Step 1-4, stand on the side facing the
drone and continue to practice Step 1-4.Then, stand in front of the
drone and repeat the steps.
drone and continue to practice Step 1-4.Then, stand in front of the
drone and repeat the steps.
Slowly lift the throttle lever. When the drone has just left the ground,
if the drone tends to move around, you can used trimming to
correct the action.
if the drone tends to move around, you can used trimming to
correct the action.
1. After the drone takes off,if the drone slowly shift to the
forward/backward direction,you can press
forward/backward (as shown in the figure) to adjust;When it
forward offset,trim down to adjust;When it backward offset,
trim up to adjust (Without controlling the direction, slight
deviation belongs to normal condition,drone without fixed
point function).
2. After the drone takes off,if the drone slowly shift to the
left/right direction,you can press left/right (as shown in the
figure) to adjust;When it right offset,trim left to adjust;When it
right offset, trim left to adjust.
forward/backward direction,you can press
forward/backward (as shown in the figure) to adjust;When it
forward offset,trim down to adjust;When it backward offset,
trim up to adjust (Without controlling the direction, slight
deviation belongs to normal condition,drone without fixed
point function).
2. After the drone takes off,if the drone slowly shift to the
left/right direction,you can press left/right (as shown in the
figure) to adjust;When it right offset,trim left to adjust;When it
right offset, trim left to adjust.
forward
backward
left
right
6.Trim
Children under 14 are prohibited
to use
to use
warning:
FCC ID: 2AQT5-GD90C-RD
Stable flight, flexible, easy realize 3D flip
When you're skilled in the basics above, you can play some thrilling flip moves.
First, fly the drone to a height of more than 2 meters. Press flip bottom, then push the
directional rocker toward the bottom of any of the four directions in front/back/left/right
and then release,
The drone flip in this direction, performing the flip steadily/swiftly.
1
3-5
6-8
9-11
Attention
Standard components
Name of components
Name of components
Controller instruction
Controller batter y installation
Calibration between drone and controller
Controller batter y installation
Calibration between drone and controller
Correct operations of drone
Flip operations of drone
Flip operations of drone
Controller’s function
Charging
Flight adjustment and notice for beginners
Flight adjustment and notice for beginners
The application of App
Replace blades
Replace blades
Problem shooting
FCC Statement
To maintain compliance with FCC s RF exposure guidelines,This equipment should be installed and
operated with minimum distance between the radiator and your body: use only the supplied
20cm
antenna.
’