SHENZHEN AOME CO. LTD RC01 ユーザーズマニュアル
QUICK GUIDE
LOCATION OF PARTS AND CONTROLS
1: Lens
2: Air outlet
3: Up
4: Confirm
Return(press more than 2 seconds)
5: Right
6: Left
7: Down
8: Power indicator
9: Audio output(3.5mm)
10: USB input/Power out
11: HDMI input
12: DC input (15V/1.5A)
LOCATION OF PARTS AND CONTROLS
1: Power
2: Speaker
3: Air inlet
4: Tripod dock
5: Rating Label
6: Non-slip mat
7: Focus wheel
8: Speaker
1
2
3
4
5
6
7
8
REMOTE CONTROL
The 2.4G wireless remote control must be paired with projector before using.
The 2.4G wireless remote control must be paired with projector before using.
Within 2 minutes after power on, press and hold the Vol
+ and Vol- around 3
seconds，then the indicator light in the remote will be flashing quickly, when the
quick flashing stopped, it will pair successfully.
quick flashing stopped, it will pair successfully.
1
2
3
4
5
6
7
8
9
10
11
12
15V
HDMI
USB
AUDIO
R
AAA Battery
Volume
Power off
Home
Confirm
Direction Key
Menu
Mouse
Return
Indicator
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: 1) this device may not cause harmful interference, and 2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device complies with RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Statement
FCC Statement
IC Note:
This device complies with Industry Canada's licence-exempt RSSs. Operation is
This device complies with Industry Canada's licence-exempt RSSs. Operation is
subject to thefollowing two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
(1) Ce dispositif ne peut causer d'interférences ; et
(2) Ce dispositif doit accepter toute interférence , y compris les interférences
(2) Ce dispositif doit accepter toute interférence , y compris les interférences
qui peuvent causer un mauvais fonctionnement de l'appareil.
Projector
S200
AOME