ICOM ic-756pro ユーザーズマニュアル
The transceiver has 5 RTTY filters in addition to nor-
mal IF filters. The passband width can be selected
from 1 kHz, 500 Hz, 350 Hz, 300 Hz and 250 Hz.
When the RTTY filter is turned ON, the RTTY tuning
meter can be used. (p. 41)
mal IF filters. The passband width can be selected
from 1 kHz, 500 Hz, 350 Hz, 300 Hz and 250 Hz.
When the RTTY filter is turned ON, the RTTY tuning
meter can be used. (p. 41)
Moreover, the twin peak filter changes the receive fre-
quency response by boosting 2 particular frequencies
(2125 and 2295 Hz) for better copying of desired
RTTY signals.
quency response by boosting 2 particular frequencies
(2125 and 2295 Hz) for better copying of desired
RTTY signals.
q
Push [CW/RTTY] once or twice to select RTTY
mode.
mode.
w
Push [RTTY FIL] to turn the RTTY filter ON.
• “TPF” appears when the twin peak filter is turned ON.
• RTTY filter selection
q
Push [EXIT] one or more times to close a multi-
function screen, if necessary.
function screen, if necessary.
w
Select RTTY mode.
e
Push [RTTY FIL] for 2 sec. to enter RTTY filter set
mode.
mode.
r
Push [(F-1)
Y
] to select band width item.
t
Rotate the tuning dial to select the RTTY filter
width from 1 kHz, 500 Hz, 350 Hz, 300 Hz and 250
Hz.
width from 1 kHz, 500 Hz, 350 Hz, 300 Hz and 250
Hz.
• Push [(F-3)DEF] for 2 sec. to select a default value.
y
Push [(F-2)
Z
] to select twin peak filter item.
• The received audio volume may become greater when
the twin peak filter is turned ON.
u
Rotate the tuning dial to turn the twin peak filter
function ON or OFF.
function ON or OFF.
i
Push [EXIT] to exit the RTTY filter set mode.
ANT
1
METER
Po
BW
BW
350
350
SFT
SFT
0
VFO
VFO
FIL2
FIL2
R T T Y
R T T Y
qw:pp
TX
TX
1
CW
CW
qr≥qpp≥pp
21.076.50
21.076.50
TPF
TPF
[RTTY FIL]
[CW/RTTY]
TPF indicator
28
5
RECEIVE AND TRANSMIT
■
RTTY reverse mode
Received characters are occasionally garbled when
the receive signal is reversed between MARK and
SPACE. This reversal can be caused by incorrect TNC
connections, settings, commands, etc.
the receive signal is reversed between MARK and
SPACE. This reversal can be caused by incorrect TNC
connections, settings, commands, etc.
To receive a reversed RTTY signal correctly, select
RTTY-R (RTTY Reverse) mode.
RTTY-R (RTTY Reverse) mode.
q
Push [CW/RTTY] once or twice to select RTTY
mode.
mode.
w
Push [CW/RTTY] for 2 sec. to select RTTY or
RTTY-R mode.
RTTY-R mode.
• Check the receive signal.
■
RTTY filter/Twin peak filter
■
CW reverse mode
CW-R (CW Reverse) mode receives CW signals with
a reverse side CW carrier point like that of LSB and
USB modes.
a reverse side CW carrier point like that of LSB and
USB modes.
Use when interfering signals are near a desired signal
and you want to change the interference tone.
and you want to change the interference tone.
q
Push [CW/RTTY] once or twice to select CW
mode.
mode.
w
Push [CW/RTTY] for 2 sec. to select CW or CW-R
mode.
mode.
• Check the interfering tone.
• Receive audio tone response
BFO
1/3 octave
Push for 2 sec.
Desired signal
(600 Hz)
(600 Hz)
CW mode (USB side)
Interference
(800 Hz)
(800 Hz)
BFO
1/2 octave
Desired signal
(600 Hz)
(600 Hz)
CW-R mode (LSB side)
Interference
(400 Hz)
(400 Hz)
CW/RTTY