DGL Group LTD. QDRTBCAM ユーザーズマニュアル

DGL Toys™ is an innovative division of DGL Group, Ltd.

Other trademarks and trade names are those of their respective owners.

DGL Toys, 

195 Raritan Center Parkway, Edison, NJ 08837.

Manufactured in China. 

Batch Ref: XXXX

Model Number: XXXX

CHOKING HAZARD-Small parts. 

Not for children under 3 years.

Tested to comply with FCC standards. 
FOR HOME OR OFFICE USE.
This device complies with part 15 of the FCC 
Rules. Operation is subject to the following two 
conditions:
(1) This device may not cause harmful 
interference  and
(2) This device must accept  any interference 
received, including interference  that may cause 
undesired operation.

• Do no mix alkaline, standard (carbon zinc), rechargeable (nickel hydride) batteries. 

• Do not mix old and new batteries. 

• Non-rechargeable batteries should not be recharged. 

• Rechargeable batteries should be removed from the appliance before being charged. 

• Rechargeable batteries should be charged under adult supervision only. 

• Exhausted batteries should be removed. 

• The supply terminals should not be short-circuited. 

• Only batteries of the same or equivalent type are recommended to be used. 

• Batteries should be inserted with the correct polarity.

quadrone

Instruction Manual

Notice

Warnings

Included

Charging Your Drone

Installing the Camera

Installing the Landing Gear and Crash Guards

Flight Controls

Practice Tips

Trimming the Quad

Speed Selection

Headless Mode

Problem

Cause

Solution

Drone’s LED lights blink continuously 

for more than 4 seconds after quad is 

turned on. No response to controller.

No response after quad is turned on.

1. Replace batteries.

2. Reinstall batteries at correct 

polarity.

Recharge quad battery.

Motor does not respond to throttle.

Motor spins but doesn’t take off.

Quad is making a loud vibration 

noise. 

Quad still wanders forward after trim 

adjustment.

Forward trim is too high.

1. Lower forward trim.

2. Recalibrate drone.

Cannot fly after crash.

1. Motor fell out.

2. Gear loosened.

1. Reinstall motor.

2. Tighten gear.

Bent or damaged rotor blades.

1. Remote batteries have been 

depleted.

2. Batteries are installed at 

incorrect polarity.

1. Bent rotor blades.

2. Quad battery is depleted.

1. Replace damaged blade.

2. Recharge battery.

Replace damaged blade.

Battery has been depleted.

Unable to sync to 

remote controller.

Repeat power 

sequence and re-sync.

(See pg. 5)

Troubleshooting

Remote Controller Diagram

Remote Controller Battery Installation

Safety Notes

Additional Warnings and Precautions

• All instructions, warranties and other collateral documents are subject    

  to change at the sole discretion of our company. 

•  If this is your first time flying a quadcopter read the manual carefully.    

  Seek the help of an experienced pilot to help you fly. These safety  

 

  instructions are intended not only for the protection of your Quadrone    

  but also to protect your own safety. Improper operation can cause  

 

  injury or property damage.

•  This product is suitable for indoor and outdoor use. Please make sure    

  you choose a flight area with no obstacles and maintain a safe distance  

  from people and pets. Do not operate near power lines.

• Read the ENTIRE instruction manual to become familiar with the  

 

  features of the product before operating. Failure to operate the product   

  correctly can result in damage to the product, personal property or  

 

  cause serious injury. This is a sophisticated hobby product. It must be    

  operated with caution and common sense, and requires some basic    

  mechanical ability. Failure to operate this product in a safe and   

  responsible manner could result in injury or damage to the product or    

  property. This product is not intended for use by children without direct   

  adult supervision. This manual contains instructions for safety,   

  operation and maintenance. It is essential to read and follow all the  

 

  instructions and warnings in this manual, prior to assembly, set up or    

  use, in order to operate correctly and avoid damage or serious injury.

 

1. Age Recommendation: Not for children under 14 years of age. This is   

  not a toy.

2. Always operate in open spaces away from obstacles, people, and  

 

 hazards.

3. Always follow directions and warnings for this and any optional  

 

  equipment carefully. (chargers, rechargeable battery packs, etc)

4. Always keep small parts and electrical parts out of the reach of  

 

 children.

5. Always avoid water exposure to all equipment not specifically   

  designed and protected for this purpose. Moisture can cause damage   

  to electronics.

6. Never place any portion of the model in your mouth as it could cause    

  serious injury or even death.

7. Never operate your model with low batteries.

 

To install batteries, use the included screw driver to open the battery 

cover. Rotate counter clockwise to loosen screw. Insert 4 AA batteries into 

the remote. Make sure the batteries are installed in the correct polarity as 

indicated in the controller. Do not mix old and new batteries or batteries 

with different chemistries. Reattach battery cover. Rotate screw clockwise 

to refasten.

Introduction

Table of Contents

• Thank you for choosing Quadrone! This is a four-axis aircraft that can    

  fly outdoors, in order to make it easier to control the aircraft. Please  

 

  carefully read this manual before operating your Quadrone. Please  

 

  keep this manual for future reference.

• Before your first flight, please take the time to carefully read this manual  

  containing important flight information which will help your first flight go   

  more smoothly.

Introduction 1

Table of Contents 

1

Notice 1

Warning 2

Additional Warnings and Precautions 

2

Safety Notes 

2

Included 3

Remote Controller Diagram 

4

Remote Controller Battery Installation 

4

Charging Your Drone 

5

Installing the Camera 

5

Syncing the Quad and Remote 

5

Flight Controls 

6

Practice Tips 

7

Trimming the Quad 

8

Flips and Rolls 

9

Speed Selection 

9

Headless Mode 

9

Auto Return 

10

Taking Photo/Video 

10

Changing the Blades 

10

Troubleshooting 12

•  RC models are composed of many precise electrical components. It is   

  important to keep the model and associated equipment away from  

 

  moisture and other contaminants. The introduction of exposure to  

 

  water or moisture in any form can cause the model to malfunction 

  or crash. Do not operate or expose to rain or moisture.

•  To avoid a potential fire hazard from batteries, do not short, reverse    

  polarity, or puncture batteries. Battery charging should be done under    

  adult supervision at all times, at a location out of reach of children. Do    

  not mix Ni-Cad and Alkaline batteries. 

•  Make sure the batteries are installed correctly to ensure correct  

 

  polarity. If you do not plan to use your Quadrone for an extended  

 

  period of time, remove the batteries from the controller to avoid battery   

  leakage which may damage the controller. Please dispose depleted    

  batteries according to local laws and ordinances.

•  Li-Polymer batteries have higher operational risks compared to other    

  batteries. It is imperative to follow proper operational guidelines. The    

  manufacturer and dealer assume no liability for accidental damages    

  caused by improper usage. Do not use any other charger other than    

  the supplied charger included in this packaging in order to avoid  

 

  potential fire or explosion. Do not crush, disassemble, burn, 

  or reverse polarity.

•  RC models are made from various forms of plastic very susceptible to    

  damage or deformation due to extreme heat and cold temperatures.    

  Make sure not to store the model near any heat source or 

  adverse temperatures.

1. Slide the camera into the slots under the drone on the battery holder to  

  secure it to the drone.

2. Connect the camera by inserting the power cable into the slot on the    

  bottom of the drone.

1. To install the landing gear, simply insert the landing gear into the  

 

  bottom of the drone. The landing gear will snap in when fully inserted.

2. To install the crash guards, insert them into the slots at the end of each  

  arm. Use the provide srew and screwdriver to secure the guard 

  in place.

•  If you are not going to use your Quadrone for an extended period of  

  time, please take out the batteries in your remote controller.  Potential  

  battery leakage could occur and possibly damage the remote or create  

  a fire hazard.

•  Use these recommended practice exercises to become a better  

  Quadrone pilot:

Flips and Rolls

•  Your Quadrone can perform impressive flips  

  and rolls in midair. In order to do this, press  

  the flip button on your remote during flight.  

  Move the directional joystick in any direction  

  and the aircraft will perform a coinciding flip.

* If the trim buttons do not correct the    

  problem, you will have to recalibrate your  

  drone. To do so, place the Quadrone on a  

  flat surface. Hold the two joysticks down  

  and to the right as depicted in the figure.  

  The lights on the will begin to flash. Once  

  the lights on the quad stop blinking for two  

  seconds, recalibration is complete.

Changing the Blades

•  If a blade breaks or falls off your Quadrone during a crash, it will be up  

  to you to repair it. Use the screwdriver included in the package to  

  remove the screw, detaching the propeller from the drone. Rotate  

  counter-clockwise to loosen. Remove the damaged blade from the  

  motor. You can now attach a new blade. It is important for the correct  

  blade to be put on the correct motor or the drone will not fly correctly. A  

  letter is marked on each blade to indicate which motor it should go on. 

 

•  When in Headless Mode, no matter what  

  direction the quadcopter faces, it will    

  respond according to the direction pushed  

  on the remote. (Forward on the remote will  

  make the quadcopter fly forward, even if it is  

  pointing in another direction.) To enter   

  Headless Mode, land the Quadrone on a flat  

  surface. Press the down on the Directional  

  Joystick. The remote will beep and the lights  

  on the quad will begin to flash. To exit   

  Headless Mode, simply press the joystick  

  again. The remote will beep again and all  

  lights will remain on and return to normal. 

Slow Speed: 1 Beep

Medium Speed: 2 Beeps

Fast Speed: 3 Beeps

Full Speed: 4 Beeps

•  If your Quadrone is leaning to or favoring a side, you may need to use  

  the trim feature to balance it out so it flies straight.

  Elevation:  Raise the Quadrone using the throttle joystick. Gradually  

   

lower the Quadrone so it lands softly to the ground.

  Direction:  Move the Quadrone in a cross pattern using the directional  

   

joystick. Move forward, backward, left, right, and back to its  

   

original position.

  Turning:  Turn the Quadrone in a throttle joystick. Turn left and right  

   

repeatedly, and back to its original position.

•  To charge your Quadrone, first  

  disconnect the battery from the  

  drone and slide it out of its holder.  

  Plug the provided USB charger into  

  a USB port. A green light on the USB  

  charger will turn on. Now connect  

  the USB charger to the battery. The  

  light on the charger will turn red, indicating the battery is now    

  charging. The red light will turn green again once the charging   

  process has completed. Always charge your Quadrone under adult  

  supervision and out of the reach of children. Charging time is    

  approximately 30 minutes. When you are ready to fly your Quadrone  

  again, reinsert the battery into its slot on the bottom of the drone.

•  Before flying your Quadrone, it is highly recommended that you  

  familiarize yourself completely with its controls. Read through the  

  instruction manual completely before attempting your first flight.

Remote Controller x1

Quadrone Tumbler-9 x1

Camera x1

Extra Blades x4

Li-Polymer Battery x1

USB Charger x1

Screwdriver x1

Push up on the throttle 

joystick. The Quadrone will 

begin to ascend.

Pull down on the throttle 

joystick. The Quadrone will 

begin to descend.

Elevation

Push the directional joystick 

to forward. The Quadrone 

will fly forward.

Push the directional joystick 

to the left. The Quadrone 

will turn to left.

Forward/Backward

Push the directional joystick 

to the right. The Quadrone 

will fly to the right.

Push the directional joystick 

to the left. The Quadrone 

will fly to left.

Aileron

Push the throttle joystick to 

the right. The Quadrone will 

turn to right.

Push the throttle joystick to 

the left. The Quadrone will 

turn to left.

Turning

If the Quadrone leans 

forward, press the Down 

Forward/Backward Trim 

button until it balances out.

If the Quadrone leans 

forward, press the Up 

Forward/Backward Trim 

button until it balances out.

Forward/Backward

If the Quadrone leans to the 

right, press the Left Aileron 

Trim button until it straightens 

out.

If the Quadrone leans to the 

right, press the Left Aileron 

Trim button until it straightens 

out.

Aileron

A

B

A

B

A

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Syncing the Quad and Remote

1. Insert the battery into the drone and connect its wires. Turn on the  

 

  drone and place it on a flat surface. The lights on the drone will begin    

  to flash. Do not move the Quadrone during the syncing process to  

 

  ensure the gyroscope stays balanced.

2. Lower the Throttle Joystick on the remote to its lowest position. Turn    

  the remote on. Push the Throttle Joystick to its highest position. The    

  lights on the Quadrone will stop flashing and stay on and the remote    

  will beep. You are now ready to fly your drone. 

•  Your Quadrone can fly at four speeds. To  

  select a speed, press the Speed Selection  

  button on your remote. Your remote will  

  beep each time you switch speeds.

Auto Return

•  To enter Auto Return simply press the Auto  

  Return button while in Headless Mode. The  

  remote will beep and the lights on the quad  

  will begin to flash. The drone will being to fly  

  directly backwards towards the remote.To  

  exit Auto Return, press the button again  

  or press forward on the Directional Joystick.

Taking Photo/Video

•  To take a photo, press up on the Photo/Video  

  button on the remote. The light on the   

  camera will flash and the remote will beep,  

  indicating a picture has been taken.

•  To take a video, press down on the    

  Photo/Video button on the remote. The light  

  on the camera will flash continuously and the  

  remote will beep twice, indicating a video is  

  being recorded. Press down on the    

  Photo/Video button again to stop recording.

Throttle

Joystick

Speed Selection

Antenna

Power lndicator

Flip Button

Directional Joystick

Headless Mode (Press)

Forward/Backward

Trim Button
Alerion

Trim Button

Light Control (Left)

Auto Return (Right)

Power Switch

Photo Button (Up)

Video Button (Down)

Battery cover

4 Alkaline batteries

  Flying: 

Once you have mastered the previous three exercises,  

   

draw a circle on the ground. Practice flying within the  

   

confines of the circle. Narrow the circle as your skills  

  

progress.

  See diagram below:

  Once you have mounted the new blade, you can refasten it with the  

  screw. Rotate clockwise to tighten.

Warning: Changes or modifications to this unit not expressly approved by the 

party responsible for compliance could void the user’s authority to operate the 
equipment.

NOTE: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and  can radiate radio 
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular 
installation. if this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the 
following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

DGL Group. Ltd.

WARRANTY REPLACEMENT DEPARTMENT

TEL: 888-987-3089

support@dglusa.com

DGL Group, Ltd. warrants to the original consumer that this product is free from 
any electrical or mechanical defects for a period or 90 DAYS from the date of 
purchase. If any such defect is discovered within the warranty period, DGL Group, 
Ltd. will repair or replace the unit free of charge upon receipt of the unit, shipped 
postage prepaid and insured to our warranty center. The warranty covers normal 
consumer use and does not cover damage that occurs in shipment of failure that 
results from alterations, accident, misuse, abuse, neglect, wear and tear, inade-
quate maintenance, commercial use or unreasonable use of the unit. Removal of 
any parts/components voids all warranties. This warranty does not cover cost of 
repairs made or attempted outside by third-party individuals and fitness, are 
hereby limited to 90 DAYS from the date or purchase. Consequential or incidental 
damages resulting from a breach of any applicable express or implied warranties 
are hereby excluded. Some states do not allow limitations on the duration of 
implied warranties and do not allow exclusion of incidental or consequential 
damages, so the above limitations and exclusions in these instances may not 
apply.

If your product begins to malfunction or stop working, immediately call or email 
our warranty center at the phone/email listed below. If it is determined that a return 
is necessary, our warranty department will issue you an RMA number/form and an 
address to the nearest return center to ship the product to. IMPORTANT NOTICE: 
We will reject all returns that are not accompanied by an issued RMA form and 
number so make sure to contact our warranty center before attempting to return 
your product!

Please repack your product in a durable box, preferably in the original carton, and 
send it prepaid, and adequately insured. Include the RMA form that was issued by 
our warranty department along with your daytime telephone number and email 
address (if available) inside the shipping carton. If your warranty has expired, 
contact our warranty center for charged service. For further information please 
send all inquiries to 

support@dglusa.com

•  Follow community-based safety guidelines, as developed by organizations  
  such as the Academy of Model Aeronautics (AMA).
•  Fly no higher than 400 feet and remain below any surrounding obstacles  
  when possible.
•  Keep your drone in eyesight at all times, and use an observer to assist 
  if needed.
•  Remain well clear of and do not interfere with manned aircraft operations,  
  and you must see and avoid other aircraft and obstacles at all times.
•  Do not intentionally fly over unprotected persons or moving  vehicles, and  
  remain at least 25 feet away from individuals and vulnerable property.
•  Contact the airport or control tower before flying within five miles 
  of an airport.
•  Do not fly in adverse weather conditions such as in high winds or 
  reduced visibility.
•  Do not fly under the influence of alcohol or drugs.
•  Ensure the operating environment is safe and that the operator is competent  
  and proficient in the operation of the drone.
•  Do not fly near or over sensitive infrastructure or property such as power  
  stations, water treatment facilities, correctional facilities, heavily traveled  
  roadways, government facilities, etc.
•  Check and follow all local laws and ordinances before flying  over 
  private property.
•  Do not conduct surveillance or photograph persons in areas where there is  
  an expectation of privacy without the individual’s permission.

WARNING!
To reduce the risk of fire or burns:
Do not disassemble, crush, puncture, or short external connectors contacts.
Use only with specified charger and player.
Do not dispose of in fire or water.
Do not expose to high temperature above 140° F (60° C).
Store between 32° F (0° C) and 140° F (60° C).
Keep away from children.
See operating instructions of this battery or product.

Batteries should be recycled or disposed of as per State and Local guidelines.

Safety Guidelines

Li-ion Battery

Must Be Disposed

Of Properly

AW-QDR-TBCAM
FCC ID:2AANZQDRTBCAM

This device complies with part 15 of the FCC rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.