Ctrack LLC RECONII ユーザーズマニュアル
Rev. 10/08/14
POWER ON
Method 1 - Press the power key at least 3 seconds and
release it to power on the Micro Tracker III device. The
GPS, GSM and power LED will light for about 3 seconds
then go off. The GSM LED will now blink once about
every five seconds.
release it to power on the Micro Tracker III device. The
GPS, GSM and power LED will light for about 3 seconds
then go off. The GSM LED will now blink once about
every five seconds.
Method 2 - Connect the device to the charger. The GPS,
Cell and power LED will light for about 3 seconds then
go off. The Cell LED will now blink once about every five
seconds.
Cell and power LED will light for about 3 seconds then
go off. The Cell LED will now blink once about every five
seconds.
POWER OFF
Method 1 - Press the power key about 3 seconds. Power
LED will light for about 3 seconds then turn off.
LED will light for about 3 seconds then turn off.
CHARGING
• Connect AC-DC power adapter to device.
• Insert the AC-DC power adapter into the power socket
• During the charging process, the Power LED light will
• Connect AC-DC power adapter to device.
• Insert the AC-DC power adapter into the power socket
• During the charging process, the Power LED light will
flash red. When the battery is fully charged, the Power
LED light will flash green. You can also charge the
battery using the USB cable which connects the Recon II
with a computer.
LED light will flash green. You can also charge the
battery using the USB cable which connects the Recon II
with a computer.
• Charging time will take about 5 hours.
When not in use, battery should be charged once a
month to maintain optimal battery performance.
month to maintain optimal battery performance.
**Note: Please fully charge your Recon II before
using the first time.
BATTERY LEVEL
To check the battery level of your device, visit the
coverttrack.com website.
To check the battery level of your device, visit the
coverttrack.com website.
COVERAGE AREA
The tracking device must be within AT&T coverage to
function. Coverage maps are available at:
The tracking device must be within AT&T coverage to
function. Coverage maps are available at:
http://www.att.com/maps/wireless-coverage.html
LIGHT SEQUENCES
GPS LED
GPS signal valid
GPS signal valid
Fast flash (blue)
GPS turned off/ GPS signal invalid
Dark
CELL LED
Network has been registered
Network has been registered
Slow flash (yellow)
Power off
Dark
Power LED
Power on and normal
Power on and normal
Dark
Fully charged
Slow flash (green)
In charging
Slow flash (red)
PANIC ALERT
To send a Panic/SOS Alert, hold down the Function button
for 3 seconds.
To send a Panic/SOS Alert, hold down the Function button
for 3 seconds.
PLACEMENT
If you are installing the device on the underside of a
vehicle, we suggest using a waterproof magnetic mount,
available from your dealer. Place the device with the
front panel facing up within the magnetic case. Then,
place the case under the vehicle within 10” of one side
of the vehicle, with the front panel facing down, towards
the ground, or out towards the horizon. Do not place
the device in the trunk, near the fuel tank, in the engine
compartment or by any other heat source.
If you are installing the device on the underside of a
vehicle, we suggest using a waterproof magnetic mount,
available from your dealer. Place the device with the
front panel facing up within the magnetic case. Then,
place the case under the vehicle within 10” of one side
of the vehicle, with the front panel facing down, towards
the ground, or out towards the horizon. Do not place
the device in the trunk, near the fuel tank, in the engine
compartment or by any other heat source.
AVAILABLE ACCESSORIES
• Weatherproof Magnetic Case
• Extended Battery Pack with Magnetic Case
• Weatherproof Magnetic Case
• Extended Battery Pack with Magnetic Case
RECON II
-
GPS Tracker
USER GUIDE
CTrack, LLC. 8361 E. Gelding Drive, Scottsdale, AZ 85260
Tracking: www.coverttrack.com Customer Support 480.657.9545
This device may not interfere with TV reception or Federal Government radar.