Zen Within Inc. ZEN01 ユーザーズマニュアル
CONCERTINA FOLD
CONCERTINA FOLD
CONCERTINA FOLD
CONCERTINA FOLD
CONCERTINA FOLD
CONCERTINA FOLD
CONCERTINA FOLD
CONCERTINA FOLD
Extra Low Voltage only. Do not connect
to mains voltages. Do not interconnect
the outputs of class two circuits
WARNING
INSIDE THE BOX
Wall mount
Main display
Adapter plate
Wire labels
2 x screws
2 x wall plugs
4 x AA Batteries
R
H
R
C
O/B
AUX
C
R
H
R
C
O/B
AUX
C
Y
1
Y
2
G
W
1
W
2
Y
1
Y
2
G
W
1
W
2
GETTING STARTED
The Zen thermostat can only
be connected to low voltage
systems. Before you begin
installation, ensure that you do
the following:
be connected to low voltage
systems. Before you begin
installation, ensure that you do
the following:
1. Turn off your mains supply
3. Check
2. Remove cover from old unit
Is your system labeled 120V-240V? Do you see thick wires with
wire-nuts? If you do your system is NOT compatible with ZEN.
If you’re unsure, please contact your home automation provider or
HVAC installer.
wire-nuts? If you do your system is NOT compatible with ZEN.
If you’re unsure, please contact your home automation provider or
HVAC installer.
4. Begin installation
If you are certain that your system is low voltage, begin the
installation process by visiting the online guide:
installation process by visiting the online guide:
zenthermostat.com/install
It takes approximately 45 minutes to get your ZEN
thermostat ready to use
thermostat ready to use
You will need an internet web browser
to complete installation
to complete installation
zenthermostat.com
Built in Malaysia
Powered by MMB Networks RapidConnect
Designed in Australia by Planet Innovation
Powered by MMB Networks RapidConnect
Designed in Australia by Planet Innovation
THIS PAGE VISIBLE WHEN FOLDED
Caring for your Zen thermostat
Clean with a damp cloth only. Avoid using chemical cleaning agents.
Clean with a damp cloth only. Avoid using chemical cleaning agents.
FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference. This device complies with Part 15
of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition
that this device does not cause harmful interference. This device complies with Part 15
of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
This equipment complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20 cm between the radiator and any part of your body.
or transmitter.
This equipment complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20 cm between the radiator and any part of your body.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS
NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Industry Canada Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Model: ZEN-01
Rating: 24VAC, 2A
FCC ID: 2ADJL-ZEN01
IC ID: 12476A-ZEN01
Rating: 24VAC, 2A
FCC ID: 2ADJL-ZEN01
IC ID: 12476A-ZEN01
PI-0026032-B-USER GUIDE ARTWORK.indd 2
21/11/2014 10:24:33 AM