Guangde Ledup Enterprise Inc. HSLSL0608 ユーザーズマニュアル

04/27/18

provided with this product.

5.To reduce the risk of fire and electric shock,use only the power supply Mode   SL08   mfd. by Ledup Enterprise (China),Inc   that was 

_____________________ 

placed where small children can reach it. 

6.This is an electric product -not a toy!To avoid risk of fire ,burns,personal injury and electric shock it should be not played with or    

of this product to connect it to other products.

4.Do not replace or modify any connectors on this product ,discard product if connector is damaged.Do not disconnect the connector

4

f 14

100L with 8 Function Starry Light Instruction Manual English

20 A

6A

77

f fire or electric shock, do not  attempt to replace lamps or modify or product.

q

p

o

n

 powe is on.\

m) Do not place loghting string on carpeting,drapes,furniture,or allow it to contact vinyl siding while the \

k

l

a)When multiple products are connected together, 

)

099

2018

2018  GH

7

Date: 

MODEL NO.

  

  

FOR INDOOR AND OUTDOOR USE

When using electric products, basic precautions should always be followed including the following:

a)

b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use.

When products are used in outdoor applications; connect the product to a Ground Fault Circuit

Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.

c) This seasonal use product is not intended for permanent installation or use.

d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.

e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.

f) Do not let LEDs rest on the supply cord or on any wire.

g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.

h) This is an electric product―not a toy! To avoid risk of fire, burns, personal injury and electric shock, it

should not be played with or placed where small children can reach it.

i) Do not use this product for other than its intended use.

j) Do not hang ornaments or other objects from cord, wire, or light string.

) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.

Do not cover the product with cloth, paper or any material not part of the product when in use.

) This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows,

unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product.

Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product.

If the replacement fuse blows, a short-circuit may be present and the product should be discarded.

) Read and follow all instructions that are on the product or provided with the product.

)

a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place

on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.

b) If the product is placed on a tree, the tree should be well secured and stable.

c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed

wire insulation or cords, cracks in the LED holders or enclosures, loose connections or exposed copper wire.

d) When storing the product, carefully remove the product from wherever it is placed, including tree branches,

or bushes to avoid any undue strain or stress on the product conductors, connections, and wires.

e) When not in use, store neatly in a cool, dry location protected from sunlight.

Most often, fuses blow because too many sets 

have been strung end-to-end.

a) Before changing fuses, make sure the set is unplugged.

c) Using a flathead screwdriver, open fuse cover. Slide open the fuse

access cover on top of attachment plug towards blades.

b) Grasp plug and remove from the

receptacle or other outlet device.

Do not unplug by pulling on cord.

d) Remove fuses carefully.

e) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).

f) Close fuse cover. Slide closed the fuse access cover on top of attachment plug. 

Make sure door is fully closed and fuses are completely covered.

g) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) 

that should not be removed. Discard product if the attachment plug is damaged.

1. This lighting string is rated

Watts (0. mps), do not overload. Connect other lighting strings or

decorative outfits end-to-end up to a maximum o

Watts (1. mps) total. If connecting to a

lighting string that does not have a Wattage (W) rating{found on the tag within 6 inches of the plug} calculate the wattage as follows:

2. To reduce the risk o

3. Do not use a dimmer switch or install any additional Christmas lighting or ornamentation that is powered by a light bulb socket.

Doing this may result in damage to your light string or cause personal injury. This action will result in a void of the limited warranty

of this product.

Size:10"x6.25"

LED

8HSTR  -1801E2

o not cl s oors

o s o

ro

r 

i n r a h s a

ir n

tion.

do not exceed the lowest 

of the indicated maximum wattage on the cord tag near the connected 
 product’s receptacle.

Connecting Sets End to End

) Caution: To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leav

branch coverings of metal or materials which look like metal, and b) Do not mount or support stri

in a manner that can cut or damage wire insulation.

7

_____ 

7.2

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,

 if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

 harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from  that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not

      expressly approved by the party responsible  for compliance 

to operate the equipment.

 could void the user's authority