Anfair Electronics Plastic Factory CAHBTAD ユーザーズマニュアル

•  To play or pause audio, press the MFB        

once.

•  To increase the volume, press the      button 

once.

•  To reduce the volume, press the      button 

once.

•  To skip to the next track, press and hold      .
•  To skip to the previous track, press and hold

      .

 

•  To make a call, use your phone’s controls, then 

select your receiver as the audio source.

•  To answer an incoming call, press the MFB       .
•  To reject an incoming call, press and hold the

 MFB        .

•  To end a call, press the MFB        once.

V2 ENGLISH 16-0647

PROBLEM
No sound or low 
volume

Cannot connect 
with Bluetooth

Bluetooth device 
keeps unpairing

NS-CAHBTAD does 
not appear on my 
Bluetooth device

No power

SOLUTION
• Make sure that your Bluetooth device is turned on, the 

Bluetooth feature is turned on, and 

NS-CAHBTAD is 

selected. 

• Turn up the volume on your receiver and Bluetooth 

device. 

• Make sure that your Bluetooth device is not muted. 
• Make sure that your receiver and Bluetooth device are 

not paired to other devices.

• Shorten the distance between your receiver and 

Bluetooth device.

• Turn your receiver and device off, then back on. Re-pair 

your receiver and Bluetooth device. 

• Make sure that your receiver and Bluetooth device are 

not paired to other devices. 

• Make sure that you have selected 

NS-CAHBTAD on your 

Bluetooth device.

• Make sure that your Bluetooth device supports the HSP, 

HFP, A2DP, or AVRCP Bluetooth protocol.

• Shorten the distance between your receiver and 

Bluetooth device. 

• Recharge the batteries in your receiver and Bluetooth 

device.

• Shorten the distance between your receiver and 

Bluetooth device. 

• Put your receiver into pairing mode (see 

RECEIVER), then, on your Bluetooth device, refresh the list 
of Bluetooth devices. (See the documentation that came 
with your Bluetooth device.)

• Make sure that your receiver’s battery is charged. See 

CHARGING YOUR RECEIVER.

• Make sure that your receiver is turned on. See 

YOUR RECEIVER.

If there is a large gap between your receiver 
and headphones when you plug in your 
receiver, use the provided foam spacer to fill 
the gap.
1  If your receiver is plugged into headphones, 

unplug it.

2  Peel off the adhesive film on the foam 

spacer, then attach the foam spacer to your 
receiver.

3  Plug your receiver back to the headphones.

FCC Statement:
This equipment has been tested and found to comply with 
the limits for a Class B digital device, pursuant to part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful 
interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more 
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and 

receiver.

—Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician 

for help.

This device complies with part 15 of the FCC Rules. Operation 
is subject to the following two conditions: (1) This device 
may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that 
may cause undesired operation.
Caution: Changes or modifications not expressly approved 
by the party responsible for compliance could void the user's 
authority to operate the equipment.
RSS-Gen & RSS-247 statement:
This device complies with Industry Canada licence-exempt 
RSS standard(s).
Operation is subject to the following two conditions: (1) this 
device may not cause interference, and (2) this device must 
accept any interference, including interference that may 
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie 
Canada applicables aux appareils radio exempts de licence. 
L'exploitation est autorisée aux deux conditions suivantes : 
(1) l'appareil ne doit pas produire de brouillage, et (2) 
l'utilisateur de l'appareil doit accepter tout brouillage 
radioélectrique subi, même si le brouillage est susceptible 
d'en compromettre le fonctionnement.
RSS-102 Statement:
This equipment complies with Industry Canada radiation 
exposure limits set forth for an uncontrolled environment.
Cet équipement est conforme à l'exposition aux 
rayonnements Industry Canada limites établies pour un 
environnement non contrôlé.

Visit www.insigniaproducts.com for details.

For customer service, call 877-467-4289 
www.insigniaproducts.com

INSIGNIA is a trademark of Best Buy and its affiliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2016 Best Buy. All rights reserved
Made in China

Foam spacer

Adhesive film

NS-CAHBTAD_16-0647_QSG_V2_EN.ai   2   8/17/2016   9:00:32 PM

NS-CAHBTAD_16-0647_QSG_V2_EN.ai   2   8/17/2016   9:00:32 PM