IGC Co. Ltd. WIPL15B-A ユーザーズマニュアル
Attaching receiver on cell phones in which parts
for wireless charging are not installed
It applies to models that do not include parts for wireless charging such
as iPhone.
as iPhone.
1
Remove the cover that is
protecting the sticker from
receiver.
protecting the sticker from
receiver.
2
Align the receiver with the
bottom of the cell phone
following the guideline of receiver.
bottom of the cell phone
following the guideline of receiver.
Product Installation
The receiver is installed in three different ways depending on the
type of cell phone.
type of cell phone.
Make sure to
check the type of cell phone
before installing
product. Refer to our website (www.wi-pl.com) for details.
The receiver is installed in different ways depending on the
type of cell phone. Check the type of cell phone that is most
appropriate for the user and attach the receiver following the
type of cell phone. Check the type of cell phone that is most
appropriate for the user and attach the receiver following the
procedures for attaching receiver of each type. If you have
completed attaching the receiver, attach the magnets following
the
completed attaching the receiver, attach the magnets following
the
procedures for attaching the magnetic sticker.
This User’s Manual explains the procedures for attaching the
receiver for two types of cell phone: cell phone in which parts for
wireless charging is not installed and cell phone in which parts for
wireless charging is partially installed.
receiver for two types of cell phone: cell phone in which parts for
wireless charging is not installed and cell phone in which parts for
wireless charging is partially installed.
Attaching receiver on cell phones in which parts
for wireless charging are partially installed
Model (example): Samsung Galaxy S5
1
Remove the cover that
is protecting the sticker
on the front side (logo)
of receiver.
is protecting the sticker
on the front side (logo)
of receiver.
2
Open the battery
cover of the cell phone
and adjust the metal
contacts of the receiver
with the metal contacts
inside the cell phone.
Then, attach the
receiver to the battery.
cover of the cell phone
and adjust the metal
contacts of the receiver
with the metal contacts
inside the cell phone.
Then, attach the
receiver to the battery.
3
While the receiver is
attached to the battery,
remove the large cover
that is protecting the
sticker on the rear side
of the receiver.
attached to the battery,
remove the large cover
that is protecting the
sticker on the rear side
of the receiver.
4
Close the battery cover
and push the cover
so that the receiver
adheres to the inside of
the cover.
and push the cover
so that the receiver
adheres to the inside of
the cover.
1
2
1
2
Attaching receiver on cell phones in which parts
for wireless charging are installed
Some of the models (e.g. Nexus series and some types of Nokia) come
equipped with a wireless receiver, and it is not necessary to attach an
extra receiver. Please contact the manufacturer to find out if the product
includes parts for wireless charging.
equipped with a wireless receiver, and it is not necessary to attach an
extra receiver. Please contact the manufacturer to find out if the product
includes parts for wireless charging.
Attaching magnetic sticker
1
1
Remove dust and water on the rear side of cell phone case or
the cell phone.
the cell phone.
2
Remove the four protecting covers of magnetic sticker.
The design of protecting cover may vary. Remove all protecting
covers.
covers.
3
Align the auxiliary film with the rear side of cell phone and
attach the magnetic sticker on the cell phone.
attach the magnetic sticker on the cell phone.
4
Remove the auxiliary film.
Auxiliary film is designed in the same size with each type of cell
phone. Magnetic sticker on the auxiliary film should be attached
on the designated location for proper charging and high charging
efficiency.
on the designated location for proper charging and high charging
efficiency.
Users can use the case they desire after attaching the receiver.
However, magnetic sticker must be attached on the cover or outside
the case so that they can be seen from outside.
the case so that they can be seen from outside.
Cases that contains metal component cannot be used as it can
cause malfunction of the product.
Magnetic sticker may be detached from the product depending on
the material used on the magnetic surface. Make sure to check the
material used on the surface when attaching the magnetic sticker.
(It is recommended to use the case when it is difficult to attach the
sticker due to the material used on the surface.)
material used on the surface when attaching the magnetic sticker.
(It is recommended to use the case when it is difficult to attach the
sticker due to the material used on the surface.)
3
Attach the receiver to cell phone.
4
Connect the receiver jack to the cell phone.
Installation on vehicle
1
1
Remove the dust or foreign substance from the glass
or dashboard that you wish to attach the cradle (glass
absorption type).
or dashboard that you wish to attach the cradle (glass
absorption type).
2
Remove the dust protecting film on the bottom side of cradle.
3
Open the lever of the cradle, attach the cradle on the
location where you wish to fix it, and then close the lever.
location where you wish to fix it, and then close the lever.
When you wish to detach and attach the cradle again, wash up the
gel on absorption part with water before attaching it.
Make sure to check if the cradle is attached properly before driving
vehicle.
Install the cradle on the location where it does not interfere with
the driver’s sight.
If the temperature difference between inside/outside is high,
absorption may be deteriorated. Make sure to check again if the
cradle is attached properly.
cradle is attached properly.
Charging battery
1
Insert the cigarette jack adapter designed for vehicle into the
cigarette lighter socket on the vehicle.
cigarette lighter socket on the vehicle.
2
Connect each end of the USB cable to the Wi-Pl, the bottom
socket (2.1 A) of cigarette jack adapter and to the battery
charger.
socket (2.1 A) of cigarette jack adapter and to the battery
charger.
3
Attach the cell phone on the battery charger. The green light
turns on at the battery charger, and the charging starts.
turns on at the battery charger, and the charging starts.
* Location of metal contacts
inside cell phones may vary
depending on the cell phone.
depending on the cell phone.
Upper (1 A) socket can be used for charging with cable.
When the power is applied, blue light turns on at the bottom part of
When the power is applied, blue light turns on at the bottom part of
the battery charger and it turns to charging standby status.
When you do not use the provided parts, power may not be supplied
properly and the battery may not charge.
When the battery is completely charged, remove the charging
cable from the main body.