Marmitek Lm12 08911 プリント
製品コード
08911
LM12™
Plug type G Art. nr. 08910
Plug type F
Art. nr. 08911
Plug type U Art. nr. 08977
Plug type I
Art. nr. 09051
Plug type CH Art. nr. 09248
Plug type W Art. nr. 09104
Universal box size (LxWxH)
90 x 74 x 144 mm with euroslot
How it works
~230V / 50Hz
Mains
The LM12 receives
and executes the
command.
The attached
appliance will be
brightened, dimmed
or turned on or off.
and executes the
command.
The attached
appliance will be
brightened, dimmed
or turned on or off.
The TM13
transmits the
command via
the mains.
transmits the
command via
the mains.
Use a Marmitek
remote control
to give the
command “dim”,
“brighten”,
“on” or “off”
remote control
to give the
command “dim”,
“brighten”,
“on” or “off”
LM12™
Also available
Set includes
Order information
© MARMITEK
22793/20101004
Smart Solutions at Home
www.marmitek.com
The Dimmer plug-in module is a 300W receiver unit that works as a remote dimmer.
The connected lamp can still be switched on and off locally. The dimmer function,
however, is by an X-10 remote control. The dimmer module can be used at any wall
outlet in the house with incandescent lamps between 40W and 300W. As the dimmer
is simply inserted into wall outlets like an ordinary plug, there is no installation neces-
sary. Just adjust the settings on the front side to the desired device address (e.g. F9)
and note this address down in a list. The lamp connected to the dimmer module can
still be controlled locally by its own switch, but do not forget to leave the local switch
in the “ON” position, otherwise the lamp cannot be controlled by an X-10 controller.
Switch the lamp off by remote control. The LM12 responds to STANDARD X-10 proto-
cols: “All lights on” or “All units off” from any X-10 controller set to its house code,
regardless of unit code. Or alternatively, by individual unit control using “On”, “Off”,
“Bright” and “Dim”.
The connected lamp can still be switched on and off locally. The dimmer function,
however, is by an X-10 remote control. The dimmer module can be used at any wall
outlet in the house with incandescent lamps between 40W and 300W. As the dimmer
is simply inserted into wall outlets like an ordinary plug, there is no installation neces-
sary. Just adjust the settings on the front side to the desired device address (e.g. F9)
and note this address down in a list. The lamp connected to the dimmer module can
still be controlled locally by its own switch, but do not forget to leave the local switch
in the “ON” position, otherwise the lamp cannot be controlled by an X-10 controller.
Switch the lamp off by remote control. The LM12 responds to STANDARD X-10 proto-
cols: “All lights on” or “All units off” from any X-10 controller set to its house code,
regardless of unit code. Or alternatively, by individual unit control using “On”, “Off”,
“Bright” and “Dim”.
Visit www.marmitek.com for our complete product range.
1x LM12
1x User Manual
English,
English,
Deutsch
Français,
Espanol,
Italiano,
Nederlands
Transmitters/Controllers
Din-rail Modules
Dimmers/Switchers
Micro Modules
Plug-in Modules
Build-in Modules
• The module is addressed by the two dials on the front, which set the House Code
and Unit Code for the module.
• When a load has its own switch, this switch can still be used to turn the unit on. The
switch needs to be clicked off and on quickly to turn the module on.
Technical data
Supply voltage
230V ±10% 50 Hz
Supply current
< 0,02 W
Making capacity
40W to 300W (normal light bulbs only)
Dimmer Speed
4.4s from 100% to 0% ±0.2s
Signal sensitivity
15 mVpp min 50 mVpp max at 120 kHz
Input impedance
> 55 Ohm (L - N) at 120 kHz
X-10 transmission
1 puls burst on 0, 60 and 120 degrees.
X-10 key codes to
All units Off, All Lights On, On, Off, Dim, Bright.
respond to
When using 3-phase
FD10 (three times) or CAT4000 needed
installation
Fuse
F 3A 250V 5 x 20 mm
Ambient temperature
-10° C to + 50° C (operation) - 20° C to + 70° C (storage)