HP 460c Gen8 670656-S01 ユーザーズマニュアル

Network Controller

Network Controller

Network Controller

Network Controller

One (1) HP FlexFabric 10Gb 2-port 554FLB FlexibleLOM

NOTE:

NOTE:

NOTE:

NOTE: Supports FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, iSCSI boot,
and autosensing 10Gb/1Gb Ethernet.
NOTE: 

NOTE: 

NOTE: 

NOTE: Each port is autosensing 1Gb/10Gb, and can interoperate with 1Gb HP BladeSystem c-Class
interconnect components. Both ports will operate at the same speed.
NOTE:

NOTE:

NOTE:

NOTE: FlexFabric capabilities require the use of an HP Virtual Connect FlexFabric module. Fibre
Channel over Ethernet (FCoE) is supported with the HP 10GbE Pass-Thru Module, HP 6120XG Blade
Switch with the CEE license installed, HP Cisco B22HP Fabric Extender and HP Cisco B22HP Fabric
Extender with 16 FET for BladeSystem c-Class. Learn more at:

Expansion Slots

Expansion Slots

Expansion Slots

Expansion Slots

Two (2) I/O expansion mezzanine slots:

x16 PCIe 3.0 Type A (supports Type A mezzanine cards) (expansion slot 1).

NOTE:

NOTE:

NOTE:

NOTE: This expansion slot supports dual-port mezzanine cards: one port is routed to interconnect
module bay 3 and the other to bay 4.

x16 PCIe 3.0 Type B (supports Type A and Type B mezzanine cards (expansion slot 2).

NOTE:

NOTE:

NOTE:

NOTE: This expansion slot supports dual-port and quad-port mezzanine cards. For dual-port
cards, one port is routed to interconnect module bay 5 and the other to bay 6. For quad-port
cards, one port is routed to interconnect module bay 5, one to bay 6, one to bay 7, and one to
bay 8.
NOTE: 

NOTE: 

NOTE: 

NOTE: A second processor must be installed (in processor slot 2) to have access to the second
expansion slot (expansion slot 2).

Mezzanine card options include:

Dual-port 10Gb FlexFabric and10Gb Flex-10 for additional network ports.
Dual-port 8Gb Fibre Channel HBA for SAN connectivity.
QDR and FDR InfiniBand for low latency and high bandwidth server interconnectivity.

HP Server ROM

HP Server ROM

HP Server ROM

HP Server ROM

HP ROM (read only memory) is now digitally signed using HP's Corporate Signing Service. This signature
is verified before the flash process starts, reducing accidental programming and preventing malicious
efforts to corrupt system ROM.

HP ROM provides for essential initialization and validation of hardware components before control is
passed to the customer-installed operating system. The ROM also provides the capability of booting from
various fixed media (HDD, CD-ROM) and removable media (USB), to continue operation to the
operating system.

HP ROM performs very early configuration of the video controller, to allow monitoring of initialization
progress via an attached monitor. If configuration or hardware errors are discovered during this early
phase of hardware initialization, suitable messages are now displayed on the connected monitor.
Additionally, these configuration or hardware errors are logged to the Integrated Management Log (IML)
to assist in diagnosis.

HP's ProLiant ROM is used to configure the following:

Processor and chipset status registers
System memory, memory map, and memory initialization
System hardware configuration (integrated PCI devices and optional PCIe cards).
Customer-specific BIOS configuration using the HP ROM-Based Setup Utility (RBSU).

HP ProLiant BL460c Generation 8 (Gen8) Server Blade

HP ProLiant BL460c Generation 8 (Gen8) Server Blade

HP ProLiant BL460c Generation 8 (Gen8) Server Blade

HP ProLiant BL460c Generation 8 (Gen8) Server Blade

DA - 14208   North America — Version 5 — March 26, 2012

Page 4