Tunturi E60R ユーザーズマニュアル

keys (10-90 minutes in steps of 5 minutes). Press 

 The equipment uses this value to calculate 

the duration of the different effort levels during the 
program.

  Enter your weight by using the arrow keys 

(default value 70 kg in the 

 window). The 

display reads 

 . Press

 Begin your workout. If the set heart rate value 

seems too strenuous or easy, change the heart rate 
value by using the arrow keys. The display shows 
the present heart rate level.

Programs can be saved in the memory of the 
console.

The console enables saving of 8 manually made 
programs to its memory.

When you wish to save a program in the memory 
of the console, press the 

 key after your 

workout session. Choose the desired memory 
location (P1-8) by using the arrow keys. Press 

Your program is now saved in the memory 

of the console. 

 A total of 32 changes can be 

saved in each profile. To save a profile, you need to 
exercise for 10 minutes or more.

 When you want to use an earlier saved program, 

press the 

key after the console has been 

switched on or after pressing 

 Choose the desired program with the 

 

key or arrow keys. Press 

.

 The time display will start to flash. Choose the 

desired duration of workout by using the arrow
keys (10-180 minutes in steps of 5 minutes, 
default: last saved time). Press

 Enter your weight by using the arrow keys 

(default value 70 kg in the 

 window). The 

display reads 

 . Press

 Begin your workout.

 If you wish, you can adjust the effort level 

with the arrow keys during the training. If you 
want to save these changes in the memory, press 
the 

key after your workout and choose the 

desired memory location. Press

 to confirm 

saving.

The values in a workout that has been interrupted 
are saved in the memory of the user interface for 
5 minutes, after which they are reset. You can 
restart the interrupted exercise by pedaling within 
5 minutes.

The user interface will display information about 
operational faults.

Err 2 Data communication problem

Remove the power cord from the power outlet, 
wait for 1 minute and then restart. If the error 
message does not disappear, please contact your 
Tunturi dealer.

Please follow these instructions when carrying 
and moving the cycle about, because lifting it 
incorrectly may strain your back or risk other 
accidents:

Always switch the power off and unplug 

the power cord before you start moving the 
equipment around!

Move the recumbent cycle according to the 
following instruction: stand behind the cycle and
take it by the seat frame with one hand and by the 
handlebar with the other hand. Lift the E60R so
that it rests on the transport wheels and move it by 
wheeling. Lower the cycle on the floor while
holding on to it and remaining all the time behind 
the equipment. 

To prevent the equipment malfunctioning, store in 
a dry place with as little temperature variation as 
possible and protected from dust.

The equipment requires very little maintenance. 
Check, however, from time-to-time that all screws 
and nuts are tight. 

 After exercising, clean the equipment with a 

soft, absorbent cloth. Do not use solvents. Sweat 
may cause corrosion: we recommend therefore that 
you protect all metal surfaces outside the plastic 
covers with teflon or car wax. 

 Never remove the equipment’s protective casing. 

 The electromagnetic brake forms a magnetic 

field that may damage the mechanism of a watch, 
or the magnetic identification strip on a credit 
or cash card, should they come into immediate 
contact with the magnets. Never attempt to detach 
or remove the electromagnetic brake! 

 The electromagnetic brake is based on 

electromagnetic resistance; resistance level is 
electronically measured and shown as watt reading 
on the display. Due to the measurement system, 
your Tunturi ergometer need not be re-calibrated 
when assembled, serviced and used according to