Tunturi T80 ユーザーズマニュアル

•

running deck according to the following instructions:

 Foldable frame

 Attach the nozzle of the lubrication tube to the T-

Lube S container.

. Lift the running belt and lock it.

. Position the nozzle between the belt and the board. 

Try to reach the spray as far into the center of the 
running deck as possible.

 Spray the lubricant for 5 seconds. 

 Lower the running deck into its normal position. 

Let the belt run for at least a minute at 1,5 kph. This is 
done to lubricate the belt evenly.

You should let the treadmill run at least five 

minutes before lifting the running deck to the storage 
position. This will prevent the lubricant from spilling.

 Solid frame

1. Attach the nozzle of the lubrication tube to the T-
Lube S container.
2. Adjust the running deck to its maximum elevation 
(10 %).
3. Position the nozzle between the belt and the board. 
Try to reach the spray as far into the center of the 
running deck as possible.
4. Spray the lubricant for 5 seconds. 
5. Lower the running deck into its normal position. 
Let the belt run for at least a minute at 1,5 kph. This is 
done to lubricate the belt evenly.

Lubricate your treadmill only with T-Lube S 

silicon lubricant. Contact your local Tunturi distributor 
for further supplies of T-Lube.

Monitor belt tracking during exercise and make 
adjustments as needed. The belt should run in the 
center of the treadmill. Alignment is not usually needed, 
provided

•

 the treadmill is placed on an even, solid and 

horizontal surface and the belt is correctly tensioned

•

 the alignment of the belt is correct

It is, however, possible for the belt to be pushed to one 
side due to the user’s running style (e.g. more weight 
on one foot). The alignment of the belt is adjusted by 
turning the two bolts at the back of the treadmill.

 Turn the power switch on and increase the treadmill’s 

speed to 5 km/h (3 mph).

 If the belt drifts to the left, turn the left adjustment 

bolt ¼ turn clockwise and the right adjustment bolt 1/8 
turn anti-clockwise. If the belt drifts to the right, turn 
the right adjustment bolt ¼ turn clockwise and the left 
adjustment bolt ¼ turn anti-clockwise.

 If the belt remains centered the adjustment is correct. 

If not, continue to make small adjustments as above 

until the belt is correctly aligned. If the belt is allowed 
run across to one side for long periods of time the edges 
of the belt may be damaged and the treadmill may not 
continue to operate correctly. Any damage to the belt 
caused by the lack of necessary adjustment will not be 
covered by the warranty.

The belt must be tensioned if it begins to slip on the 
rollers. In normal use, however, keep the belt as loose 
as possible! The belt tension is adjusted by turning the 
same screws as used for aligning the running belt. If 
turning the screws will not effect the belt tension, please 
contact your local Tunturi dealer.

Increase the treadmill’s speed to 5 km/h (3 mph).

 Turn both adjustment screws an equal amount, ¼ 

turn clockwise.

 Try to slow the belt down by holding onto the 

handrails and braking as you walk (as if you were 
walking downhill). 

If the belt slips, turn another ¼ turn and repeat the test. 
When braking heavily the belt may slip. If the belt keeps 
slipping despite repeated adjustments, please contact 
your local Tunturi dealer.

Despite continuous quality control, defects and 

malfunctions caused by individual components may 
occur in the equipment. In most cases it’s unnecessary 
to take the whole device in for repair, as it’s usually 
sufficient to replace the defective part. Always give 
the model, serial number of your equipment and in 
case of malfunctions also conditions of use, nature of 
malfunction and any error code.

When you encounter unusual behavior from the 
treadmill, simply turn the power switch off, wait 1 
minute and turn the power switch on to reset the 
treadmill. This should clear incidental errors and ready 
the treadmill for normal operation again. If after you 
have reset the treadmill by turning the power switch off 
and on again, and the treadmill is still not operational, 
contact your local Tunturi dealer for service.

If you require spare parts, always give the model, serial 
number of your equipment and the spare part number 
for the part you need. The spare part list is at the back 
of this manual. Use only spare parts mentioned in the 
spare part list.

The user interface will display information about 
operational faults.

SYSTEM CHECK FAILED. Possible motor controller 
fault. Turn the power switch off, wait 1 minute and 
turn the power switch on again. If treadmill recovers 
to normal operation, you may continue to use the 
treadmill. Otherwise, call the dealer for service.

SPEED SENSOR ERROR. Call the dealer for service. 

T80_T85_manual.indd   13

T80_T85_manual.indd   13

28.2.2006   17:38:34

28.2.2006   17:38:34