Panasonic RPWF6000 ユーザーズマニュアル
RQT8948
6
7
RQT8948
ENGLISH
Using the rechargeable battery (supplied)
The supplied rechargeable battery must be charged before using this unit.
Inserting the supplied nickel-metal hydride rechargeable battery
1
Press the [BATT] knob on the left housing
a to open the battery compartment lid b
and then take it off.
a to open the battery compartment lid b
and then take it off.
2
Insert the supplied nickel-metal hydride
rechargeable battery.
rechargeable battery.
● Align the poles
+ and - correctly when inserting.
● Push down on the
- pole spring when inserting.
Remove the
+ poles fi rst when removing.
3
Insert the rib
c on the battery compartment
lid into the hole on the left housing and then
close the battery compartment lid.
close the battery compartment lid.
Push the battery compartment lid until it locks.
Charging
1
Connect the AC adaptor (supplied)
d to the transmitter.
d to the transmitter.
2
Put the headphones on the
transmitter making sure that the
charging terminals
transmitter making sure that the
charging terminals
f are in contact
with each other.
g Left housing
The battery can be charged with the headphones
placed vertically or horizontally.
● The OPR/CHARGE lamp
The battery can be charged with the headphones
placed vertically or horizontally.
● The OPR/CHARGE lamp
h on the transmitter
glows red.
● The OPR/CHARGE lamp
h goes out when the
battery is fully charged.
● When putting the headphones on the
transmitter, hold the left and right housings in
each hand and put the headphones straight
down onto the transmitter.
each hand and put the headphones straight
down onto the transmitter.
● Radio wave emission automatically stops when the headphones are placed onto the transmitter.
● The headphones can be used even if the battery is not fully charged.
● Disconnect the AC adaptor from the household AC outlet if the unit is not going to be used for a long time. This
● The headphones can be used even if the battery is not fully charged.
● Disconnect the AC adaptor from the household AC outlet if the unit is not going to be used for a long time. This
unit consumes a small amount of power (approximately 1.8 W) if the AC adaptor is connected, even when it is
turned off.
turned off.
The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always “live” as long
as the AC adaptor is connected to an electrical outlet.
● Charge the battery in an environment with an ambient temperature between 0 °C and 40 °C or it may not be fully
charged.
Nickel-metal hydride rechargeable battery
Use the supplied battery or a dedicated replacement battery
RP-BP6000 (optional).
RP-BP6000 (optional).
Commercially available rechargeable batteries
You cannot charge commercially available rechargeable
batteries.
batteries.
Note
● The AC adaptor power cord (supplied)
e is for use
with this unit only. Do not use it with other equipment.
Do not use cords from other equipment with this
unit.
Do not use cords from other equipment with this
unit.
● Be sure to use the supplied AC adaptor.
Note
The headphones are recharged if they are put back
onto the transmitter after being fully charged.
Do not keep recharging the battery if it is not used
between recharges.
The battery will be overcharged causing overheating
and electrolyte leakage.
onto the transmitter after being fully charged.
Do not keep recharging the battery if it is not used
between recharges.
The battery will be overcharged causing overheating
and electrolyte leakage.
Charging and operating times
※1
At 1 kHz, 1 mW + 1 mW output.
※2
Time required to fully charge from empty.
※3
Operating times may differ depending on the temperature of the surrounding environment and operating
conditions.
Power supply preparations: Headphones
Transmitter
To DC-IN 9V terminal
To household AC outlet
6
Placing the headphones vertically
Placing the headphones horizontally
Charging time
Operating time
※1
Approx. 3 hours
※2
Approx. 8 hours
※3
7
For your reference