Da-Lite Large Advantage Deluxe Electrol 36867 プリント
製品コード
36867
SUGGESTED SPECIFICATIONS: projection screen(s),
(H) x (W). The Advantage® Deluxe Screen shall have
two motors, one to operate door and one to operate screen. Door motor
electrically operated 120 volt (60 Hz) not more than 1.2 amp, mounted inside
the roller, to be three wire with ground, quick reversal type, oiled for life, with
automatic thermal overload cutout, integral gears, capacitor and an electric
brake to prevent coasting. To have pre-set but adjustable limit switches to
automatically stop fabric door in the open position. The roller to be of 1.6"
diameter aluminum. Screen motor is electrically operated 120 volt (60 Hz) not
more than 2.4 amp, mounted inside the roller, to be three wire with ground
quick reversal type, oiled for life, with automatic thermal overload cutout,
integral gears, capacitor and an electric brake to prevent coasting. To have pre-
set but adjustable limit switches to automatically stop picture surface in the
“up” and “down” positions. Rigid metal roller, to be at least 5¾" in diameter (on
screens 14' to 18' wide) or 7" in diameter (on screens where either height or
width equal or exceed 20'). Screen fabric to be flame retardant and mildew
resistant fiberglass with black masking borders standard. Bottom of fabric shall
(H) x (W). The Advantage® Deluxe Screen shall have
two motors, one to operate door and one to operate screen. Door motor
electrically operated 120 volt (60 Hz) not more than 1.2 amp, mounted inside
the roller, to be three wire with ground, quick reversal type, oiled for life, with
automatic thermal overload cutout, integral gears, capacitor and an electric
brake to prevent coasting. To have pre-set but adjustable limit switches to
automatically stop fabric door in the open position. The roller to be of 1.6"
diameter aluminum. Screen motor is electrically operated 120 volt (60 Hz) not
more than 2.4 amp, mounted inside the roller, to be three wire with ground
quick reversal type, oiled for life, with automatic thermal overload cutout,
integral gears, capacitor and an electric brake to prevent coasting. To have pre-
set but adjustable limit switches to automatically stop picture surface in the
“up” and “down” positions. Rigid metal roller, to be at least 5¾" in diameter (on
screens 14' to 18' wide) or 7" in diameter (on screens where either height or
width equal or exceed 20'). Screen fabric to be flame retardant and mildew
resistant fiberglass with black masking borders standard. Bottom of fabric shall
be formed into a pocket holding a metal rod with plastic caps. Case shall be a
white powder coated aluminum extrusion. Bottom of case to be self-trimming
with a built-in flange around the bottom of the case. A section of the bottom of
the case shall be a retractable aluminum door that opens and closes
automatically with the lowering and raising of the picture surface. The balance
of the bottom of the case shall be a second aluminum door with manual
opening to provide access. Junction box shall be internally integrated into the
housing making it possible to install the housing and wire to the building’s
electrical system during construction. The junction box shall contain a quick
connect connector that is mounted in the housing for easy plug-in connection
to the motorized fabric and roller assembly. The motorized fabric and roller
assembly to be installed in the case at the factory or at a later time at the job
site. To be complete with integrated low voltage control unit and three position
control switch with cover plate. Suitable for use in environmental air space in
accordance with section 300-22 (c) of the National Electric Code, and sections
2-128, 12-010 (3) and 12-100 of the Canadian Electrical Code, part 1, CSA C22.1.
Screen to be listed by Underwriters’ Laboratories.
white powder coated aluminum extrusion. Bottom of case to be self-trimming
with a built-in flange around the bottom of the case. A section of the bottom of
the case shall be a retractable aluminum door that opens and closes
automatically with the lowering and raising of the picture surface. The balance
of the bottom of the case shall be a second aluminum door with manual
opening to provide access. Junction box shall be internally integrated into the
housing making it possible to install the housing and wire to the building’s
electrical system during construction. The junction box shall contain a quick
connect connector that is mounted in the housing for easy plug-in connection
to the motorized fabric and roller assembly. The motorized fabric and roller
assembly to be installed in the case at the factory or at a later time at the job
site. To be complete with integrated low voltage control unit and three position
control switch with cover plate. Suitable for use in environmental air space in
accordance with section 300-22 (c) of the National Electric Code, and sections
2-128, 12-010 (3) and 12-100 of the Canadian Electrical Code, part 1, CSA C22.1.
Screen to be listed by Underwriters’ Laboratories.
SPECIFICATION DATA
Video (NTSC 4:3) Format Dimensions (2" Standard Black Drop at Top)
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
123" x 164"
312 x 417
210"
533
183½"
466
587
266.3
141" x 188"
358 x 478
240"
610
207½"
527
662
300.3
159" x 212"
404 x 538
265"
673
231½"
588
738
334.8
177" x 236"
450 x 599
295"
749
255½"
649
847
384.2
HDTV (16:9) Format Dimensions (2" Standard Black Drop at Top)
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
106" x 188"
269 x 478
216"
549
207½"
527
651
295.3
119" x 212"
302 x 538
243"
617
231½"
588
724
328.4
133" x 236"
338 x 599
271"
688
255½"
649
830
376.5
Wide (16:10) Format Dimensions
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
110" x 176"
279 x 447
208"
528
195½"
497
631
286.2
117½" x 188"
283 x 478
222"
564
207½"
527
662
300.3
Square Format Dimensions (Screens With
^ Have 2" Standard Black Drop at Top)
Viewing Area (H x W)
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
Lbs.
Kg
10'6" x 14'
^
320 x 427
183½"
466
588
266.7
14' x 14'
427 x 427
183½"
466
599
271.7
12' x 16'
^
366 x 488
207½"
527
663
300.7
16' x 16'
488 x 488
207½"
527
671
304.4
13'6" x 18'
^
411 x 549
231½"
588
738
334.8
18' x 18'
549 x 549
231½"
588
757
343.4
15' x 20'
^
457 x 610
255½"
649
847
384.2
20' x 20'
610 x 610
255½"
649
871
395.1
16'6" x 22'
^
503 x 671
279½"
710
929
421.4
22' x 22'
671 x 671
279½"
710
958
434.5
18' x 24'
^
549 x 732
303½"
771
1012
459.0
*Case length does not include flange
Large Advantage
®
Deluxe Electrol
®
Automatic Electric Projection Screen Model