Intel J1750 FH8065301562600 ユーザーズマニュアル
製品コード
FH8065301562600
Datasheet
79
Electrical Specifications
•
Non-Operating Temperature Limit: -40 °C to 70 °C
•
Humidity: 50% to 90%, non-condensing with a maximum wet-bulb of 28 °C
8.3
Voltage and Current Specifications
The I/O buffer supply voltages are specified at the processor package balls. The
tolerances shown in the following table are inclusive of all noise from DC up to 20 MHz.
The voltage rails should be measured with a bandwidth limited oscilloscope with a roll-
off of 3 dB/decade above 20 MHz under all operating conditions.
tolerances shown in the following table are inclusive of all noise from DC up to 20 MHz.
The voltage rails should be measured with a bandwidth limited oscilloscope with a roll-
off of 3 dB/decade above 20 MHz under all operating conditions.
indicates
which supplies are connected directly to a voltage regulator or to a filtered voltage rail.
For voltage rails that are connected to a filter, they should be measured at the input of
the filter. If the recommended platform decoupling guidelines cannot be met, the
system designer will have to make trade-offs between the voltage regulator out DC
tolerance and the decoupling performances of the capacitor network to stay within the
voltage tolerances listed below.
For voltage rails that are connected to a filter, they should be measured at the input of
the filter. If the recommended platform decoupling guidelines cannot be met, the
system designer will have to make trade-offs between the voltage regulator out DC
tolerance and the decoupling performances of the capacitor network to stay within the
voltage tolerances listed below.
Note:
The SoC is a pre-launch product. Voltage and current specifications are subject to
change.
change.
Platform Rail
Voltage
Tolerances
Max Icc
-M
(2.xW SDP)
Max Icc
-M
Max Icc
-D
V1P0A
- UNCORE_V1P0_G3
- USB3_V1P0_G3
- UNCORE_V1P0_G3
- USB3_V1P0_G3
1.0 V
DC: ±2%
AC: ±3%
325 mA
325 mA
350 mA
V1P24A
- USB_HSIC_V1P24_G3
(Can connect to V1P0A when USB
- USB_HSIC_V1P24_G3
(Can connect to V1P0A when USB
HSIC isn’t used)
1.24 V
DC: ±3%
AC: ±2%
35 mA
35 mA
35 mA
V1P8A
- PCU_V1P8_G3
- PMC_V1P8_G3
- UNCORE_V1P8_G3
- USB_V1P8_G3
- USB_ULPI_V1P8_G3
- PCU_V1P8_G3
- PMC_V1P8_G3
- UNCORE_V1P8_G3
- USB_V1P8_G3
- USB_ULPI_V1P8_G3
1.8 V
DC: ±3%
AC: ±2%
65 mA
65 mA
65 mA
V3P3A
- PCU_V3P3_G3
- USB_V3P3_G3
- PCU_V3P3_G3
- USB_V3P3_G3
3.3 V
DC: ±2%
AC: ±3%
50 mA
50 mA
55 mA
V1P0Sx
- UNCORE_V1P0_S3
- DRAM_V1P0_S3
- DDI_V1P0_S3
- UNCORE_V1P0_S3
- DRAM_V1P0_S3
- DDI_V1P0_S3
1.0 V
DC: ±2%
AC: ±3%
1.9 A
1.9 A
2.1 A
V1P35Sx (VSFR)
- DRAM_V1P35_S3_F1
- UNCORE_V1P35_S3_F[6:1]
- DRAM_V1P35_S3_F1
- UNCORE_V1P35_S3_F[6:1]
1.35 V
DC: ±3%
AC: ±2%
375 mA
375 mA
400 mA