Avid DigiLink MH088 プリント

製品コード
MH088
ページ / 2
Digidesign offers an array of quality cabling
options to ensure the reliable passage of audio 
signals as they travel between the I/O components
of your Pro Tools system. Designed specifically
for Digidesign gear, these cables make for con-
sistent, logical and organized patching solutions.
Digidesign cable products fall into two cate-
gories: DigiSnakes and DigiLinks. DigiSnakes
are eight channel audio snakes providing con-
nections between your studio and Digidesign’s
control surfaces or 192 I/O or PRE interfaces.
All DigiSnakes are custom-colored and
labeled, and are built with 110 ohm digital-
grade cable allowing them to accommodate
either digital or analog signals.They are
available individually or in “kit” form specif-
ic to Digidesign’s control surfaces. DigiLink
interface cables connect Pro Tools|HD I/O
peripherals to HD PCI cards, or HD I/Os to
HD I/Os.They are available in lengths from
1.5 feet to 100 feet to allow customized
studio installations.
Whether you need a cable solution for
closed system use or for integrating out-
board gear into your Pro Tools environment,
Digidesign cables serve to optimize your
HD- or MIX-based studio. Connecting your
gear becomes a quick and easy process,
freeing you to invest your valuable time in
your audio projects rather than the wires
they travel across.
I
NDIVI DUAL
D
IGI
S
NAKES
DB25-XLR M+F AES/EBU DigiSnake:
This configuration is comprised of a DB25
connector to four XLR male and four 
XLR female connectors. Below 192 kHz,
AES/EBU carries two channels per line; so
this snake simultaneously transmits eight in
and eight out via the eight XLR connectors.
At 192 kHz sample rate, 192 I/O uses dual
wire transmission; in that case, this snake
transmits four in and four out, and the connec-
tor labeled “output 1&2” is output 1, “output
3&4” is output 2, and so forth.The four XLRM
jackets are black and the four XLRF wire jack-
ets are yellow, and all include appropriate
labeling. Available in 12- or 4-foot lengths.
DB25-XLRM DigiSnake
This option is an output snake, consisting of DB25 
to eight XLR male connectors. Red jackets with
appropriate labeling are located at both ends.
Available in 12- or 4-foot lengths.
DB25-XLRF DigiSnake
This option is an input snake, comprised of DB25
to eight XLR female connectors. Blue jackets with
appropriate labeling are located on both ends.
Available in 12- or 4-foot lengths.
DB25-TRS DigiSnake
This DigiSnake includes DB25 to eight balanced
TRS connectors for audio input or output. Orange
jackets with appropriate labeling are located on
both ends. Available in 12- or 4-foot lengths.
DB25-TS +4 dBu/-10 dBV Padded DigiSnake
Comprised of a balanced +4 dBu DB25 to unbal-
anced -10 dBV  TS snake, this option contains the
appropriate padding circuit to reduce 192 I/O's 
+4 dBu output signal down to -10 dBV.This
DigiSnake is intended for +4 dBu output only;
use any other input snake for return/input. Grey
jackets with appropriate labeling are located on
both ends. Available in 12- or 4-foot lengths.
DB25-DB25 DigiSnake
This DigiSnake employs a DB25 to DB25 
configuration using standard wiring. Color 
matched jackets are found on both ends.Typically
used for communication between any two standard
DB25-equipped devices (e.g., PRE out to 192 I/O
analog in), this DigiSnake cannot be used for
AES/EBU or TDIF digital dubbing. For TDIF 
dubbing, use the TDIF DigiSnake; or for AES/EBU
digital dubbing, use two AES/EBU DigiSnakes,
connected end to end (XLR to XLR). Available in
25-, 12- or 4-foot lengths.
DB25-DB25 TDIF-Only DigiSnake
This TDIF digital (dubbing) cable is designed for
digital TDIF transfers only. It can only be used for
TDIF to TDIF (e.g.,Tascam MDM to 192 I/O TDIF
connector) connections; it cannot be used for
AES/EBU digital dubbing. For AES/EBU digital
dubbing, use two AES/EBU DigiSnakes, connected
end to end (XLR to XLR). Brown jackets with
appropriate labeling are located on both ends.
Available in 12-foot length.
A division of
Avid
D
IGI
S
NAKES
DigiSnakes: Audio snakes for
connecting digital or analog
external gear to Digidesign
I/Os or control surfaces
D
IGI
S
NAKE
K
ITS
“All snakes in one box”
solutions for connecting
Digidesign control surfaces
to Digidesign I/Os or 
external gear
Multiple DigiSnake and
DigiSnake Kit configurations
Custom printing and color-
coding designed specifically
for Pro Tools systems
Lifetime warranty
D
IGI
L
INK
Interface cable for connect-
ing Pro Tools|HD I/Os to 
HD Cores, or HD I/Os to
additional HD I/Os
Multiple lengths up to 
100 feet for custom 
HD I/O installations
|
F E A T U R E S
|
DigiSnakes, DigiSnake Kits & DigiLink Cables
Customized Audio Cabling for Pro Tools Systems
2001 Junipero Serra Blvd.
|
Daly City, CA  94014-3886
|
www.digidesign.com
|
Tel 650.731.6300
|
Fax 650.731.6399
M
Mac OS
W
Windows