Gefen GTB-UHD2IRS-ELRPOL-BLK プリント
GTB-UHD2IRS-ELRPOL-BLK
Extend HDMI, RS-232, and 2-way IR over one CAT-5e cable, up to
495 feet (150 meters)
The GefenToolBox 4K Ultra HD ELR Extender for HDMI with POL uses Gefen’s implementation
of the HDBaseT® technology to extend HDMI up to 495 feet (150 meters) using one CAT-5e
cable. Resolutions up to 4K Ultra HD with 7.1 channels of HBR (High Bit Rate) lossless digital
audio are supported. This product provides RS-232 and 2-way IR extension between the Sender
and the Receiver units, allowing the transfer of IR commands and RS-232 communications
between two remote locations. RS-232 and Bi-Directional IR can be used to control A/V
sources placed near the Sender unit and to send automation commands to the display or any
other device placed near the Receiver unit. Gefen POL (Power Over Line) technology powers
the Receiver unit using the same cable that extends the HDMI signal from the Sender unit.
This feature eliminates the need for an external power supply for the Receiver unit and simplifies
installation.
of the HDBaseT® technology to extend HDMI up to 495 feet (150 meters) using one CAT-5e
cable. Resolutions up to 4K Ultra HD with 7.1 channels of HBR (High Bit Rate) lossless digital
audio are supported. This product provides RS-232 and 2-way IR extension between the Sender
and the Receiver units, allowing the transfer of IR commands and RS-232 communications
between two remote locations. RS-232 and Bi-Directional IR can be used to control A/V
sources placed near the Sender unit and to send automation commands to the display or any
other device placed near the Receiver unit. Gefen POL (Power Over Line) technology powers
the Receiver unit using the same cable that extends the HDMI signal from the Sender unit.
This feature eliminates the need for an external power supply for the Receiver unit and simplifies
installation.
How It Works
Connect the Sender unit to a Hi-Def source using the included HDMI cable. Use another HDMI
cable to connect the Receiver unit to a display. Connect a single CAT-5e or better cable
between the Sender and Receiver units. To control the source from the display location via IR,
connect the included IR extender (Gefen part no. EXT-RMT-EXTIRN) to the IR Ext connector on
the Receiver unit. Connect the included IR emitter (Gefen part no. GTB-IREMIT) to the IR Out
port of the Sender unit and place the IR emitter over the IR sensor of the source. Point the IR
remote at the IR extender to control the source. For IR control of a device placed near the
Receiver unit (such as the display), connect the IR output from an automation control device to
the IR In connector on the Sender unit. Connect an IR emitter (Gefen part no. EXT-IREMIT) to
the IR Out port on the Receiver unit and attach the IR emitter to the IR sensor of the device
being controlled. To extend RS-232 between the local and remote locations, connect the
included male-to-female DB-9 cable from the Sender to an automation control device, and
connect another DB-9 cable of the same type from the Receiver unit to the device to be
controlled. Connect the included 24V DC power supply to the Sender unit and plug it into an
available electrical outlet. Power to the Receiver unit is delivered from the Sender unit over the
CAT-5e cable using Gefen POL technology. Power on all associated equipment.
cable to connect the Receiver unit to a display. Connect a single CAT-5e or better cable
between the Sender and Receiver units. To control the source from the display location via IR,
connect the included IR extender (Gefen part no. EXT-RMT-EXTIRN) to the IR Ext connector on
the Receiver unit. Connect the included IR emitter (Gefen part no. GTB-IREMIT) to the IR Out
port of the Sender unit and place the IR emitter over the IR sensor of the source. Point the IR
remote at the IR extender to control the source. For IR control of a device placed near the
Receiver unit (such as the display), connect the IR output from an automation control device to
the IR In connector on the Sender unit. Connect an IR emitter (Gefen part no. EXT-IREMIT) to
the IR Out port on the Receiver unit and attach the IR emitter to the IR sensor of the device
being controlled. To extend RS-232 between the local and remote locations, connect the
included male-to-female DB-9 cable from the Sender to an automation control device, and
connect another DB-9 cable of the same type from the Receiver unit to the device to be
controlled. Connect the included 24V DC power supply to the Sender unit and plug it into an
available electrical outlet. Power to the Receiver unit is delivered from the Sender unit over the
CAT-5e cable using Gefen POL technology. Power on all associated equipment.
Note:
Shielded (STP) CAT-5e or CAT-6 is recommended. Unshielded (UTP) CAT-5e or CAT-6
may be acceptable depending on cable quality but is not the best choice. Care should always
be given to keep these cables away from power lines and other sources of electromagnetic
interference.
be given to keep these cables away from power lines and other sources of electromagnetic
interference.
Features*
• Extends 4K Ultra HD (3840 x 2160 @ 30 Hz, 8-bit color**), RS-232, and Bi-Directional IR,
up to 230 feet/70 meters over a single CAT-5e cable, or up to 330 feet/100 meters over a
single CAT-6A cable
• Extends HDMI at 1080p Full HD, RS-232, and Bi-Directional IR, over a single CAT-5e cable
up to 495 feet/150 meters (8-bit color**) or up to 330 feet/100 meters (up to 12-bit Deep Color)
• HDMI Features Supported:
• HDCP
• 12-bit Deep Color
• LPCM 7.1 audio, Dolby® TrueHD, and DTS-HD Master Audio™ pass-through
• 3DTV pass-through
• CEC pass-through
• Lip Sync pass-through
• RS-232 Extension
• 2-way IR extension from Sender to Receiver and from Receiver to Sender
• Gefen POL feature provides power to the Receiver unit over the link cable
• Uses Gefen’s implementation of HDBaseT® technology
• EDID pass-through
• Locking power connector
• Surface mountable
up to 230 feet/70 meters over a single CAT-5e cable, or up to 330 feet/100 meters over a
single CAT-6A cable
• Extends HDMI at 1080p Full HD, RS-232, and Bi-Directional IR, over a single CAT-5e cable
up to 495 feet/150 meters (8-bit color**) or up to 330 feet/100 meters (up to 12-bit Deep Color)
• HDMI Features Supported:
• HDCP
• 12-bit Deep Color
• LPCM 7.1 audio, Dolby® TrueHD, and DTS-HD Master Audio™ pass-through
• 3DTV pass-through
• CEC pass-through
• Lip Sync pass-through
• RS-232 Extension
• 2-way IR extension from Sender to Receiver and from Receiver to Sender
• Gefen POL feature provides power to the Receiver unit over the link cable
• Uses Gefen’s implementation of HDBaseT® technology
• EDID pass-through
• Locking power connector
• Surface mountable
** This product passes through the display’s EDID to the source. If the display is capable of accepting
Deep Color, the source must be manually configured to output 8-bit color.
Deep Color, the source must be manually configured to output 8-bit color.
Specifications*
• Maximum Pixel Clock: 300 MHz
• Maximum TMDS Clock: 300 MHz
• Video Input Connector (Sender): (1) HDMI Type A 19-pin, female, locking
• Video Output Connector (Receiver): (1) HDMI Type A 19-pin, female, locking
• Link Connector (Sender/Receiver): (1) RJ-45, shielded
• RS-232 port (Sender): (1) DB-9, female
• RS-232 port (Receiver): (1) DB-9, male
• IR Extender port (Receiver): (1) 3.5mm mini-stereo jack
• IR Extender type: EXT-RMT-EXTIRN
• IR Out port (Sender/Receiver): (1) 3.5mm mini-mono jack
• IR In port (Sender): (1) 3.5mm mini-mono jack
• Power/HDCP Indicator LED (Sender/Receiver): (1) Bi-color: Blue/Amber
• Power Supply: (1) 24V DC, locking
• Power Consumption: 10W maximum
• Operating Temperature: 0 to +50 °C
• Operating Humidity: +10 to +90%, Relative Humidity, non-condensing
• Storage Temperature: -20 to +85 °C
• Storage Humidity: 0 to +95%, Relative Humidity, non-condensing
• MTBF: 50000 hours
• Dimensions (W x H x D) (Sender / Receiver): 4.3” x 1” x 3.2” (110mm x 26mm x 80mm)
• Unit Weight (Sender/Receiver): 0.35 lbs. (0.2 kg)
• Shipping Weight: 2.6 lbs. (1.2 kg)
• Maximum TMDS Clock: 300 MHz
• Video Input Connector (Sender): (1) HDMI Type A 19-pin, female, locking
• Video Output Connector (Receiver): (1) HDMI Type A 19-pin, female, locking
• Link Connector (Sender/Receiver): (1) RJ-45, shielded
• RS-232 port (Sender): (1) DB-9, female
• RS-232 port (Receiver): (1) DB-9, male
• IR Extender port (Receiver): (1) 3.5mm mini-stereo jack
• IR Extender type: EXT-RMT-EXTIRN
• IR Out port (Sender/Receiver): (1) 3.5mm mini-mono jack
• IR In port (Sender): (1) 3.5mm mini-mono jack
• Power/HDCP Indicator LED (Sender/Receiver): (1) Bi-color: Blue/Amber
• Power Supply: (1) 24V DC, locking
• Power Consumption: 10W maximum
• Operating Temperature: 0 to +50 °C
• Operating Humidity: +10 to +90%, Relative Humidity, non-condensing
• Storage Temperature: -20 to +85 °C
• Storage Humidity: 0 to +95%, Relative Humidity, non-condensing
• MTBF: 50000 hours
• Dimensions (W x H x D) (Sender / Receiver): 4.3” x 1” x 3.2” (110mm x 26mm x 80mm)
• Unit Weight (Sender/Receiver): 0.35 lbs. (0.2 kg)
• Shipping Weight: 2.6 lbs. (1.2 kg)
Gefen, LLC
20600 Nordhoff Street, Chatsworth CA 91311
Tel. (818) 772-9100 (800) 545-6900 Fax (818) 772-9120
www.gefen.com
* Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
Copyright© 2014 Gefen LLC
4K Ultra HD Extender for HDMI
with RS-232, Bi-Directional IR, and POL
®
1080P
®
VER. A2