Audix D2 AUDIX D2 プリント

製品コード
AUDIX D2
ページ / 2
SPECIFICATIONS:
ARCHITECTS AND ENGINEERS SPECIFICATIONS:
The microphone shall be of the dynamic type operating on the moving coil principle and the 
capsule shall be VLM Type B. The polar pattern of the microphone shall be hypercardioid. The 
nominal output impedance shall be 250 ohms at 1 kHz.The microphone shall have a sensitivity of 
1.2 mV / Pa at 1 kHz and will handle a sound pressure level of ≥144 dB. The microphone body 
shall be machined of  aluminum and the grill cap shall be steel wire mesh.  The overall dimensions 
shall be 21.5 mm in diameter at the base, 39 mm in diameter at the widest point and 100 mm in 
length. The microphone shall be the Audix D2.
 
OPERATION:
The D2 is a low impedance microphone and should be plugged into a “mic level” of your console, 
mixer, or recording device. Please note that your microphone does not require phantom power 
and will not be effected in any way by phantom power should it be running simultaneously while 
the microphone is in operation. Avoid plugging or unplugging the microphone from the PA system 
unless the channel is muted or the volume of the system turned down. Failure to do so may result 
in a loud “popping” noise which could seriously damage the speakers in the PA system.
USER TIPS:
The D2 has an extremely tight (hypercardioid) pick-up pattern in order to help eliminate sound 
from other instruments on stage from “bleeding” into the microphone. For this reason, the D2 is 
exceptionally effective in capturing the sound of each component of a drum or percussion kit.
Drums, hand percussion: As a general rule, the bottom of the D2 grill should be 1-2 inches 
above the head of the drum and pointed towards the center. For more “ring” pull the mic back 
towards the rim. For less ring and more overtones, position the mic 1-2 inches inside the ring. For 
more attack, place the mic very close to the head and for more overtones and decay move the 
mic further away from the head.
Guitar cabinets: The D2 can be placed within 1-2 inches of the grill cover at a 90 degree angle 
pointing directly into the speaker. If the mic is placed closer to the edge of the speaker, you will 
minimize the higher frequencies and get a warmer, fatter tone. To capture more highs, move the 
mic closer towards the center of the speaker, but avoid the middle of the speaker. 
Horns: Place the mic within 1-2 inches of the bell, especially when on a stage with drums, bass, 
guitar, etc. For jazz, classical, and music where the stage volume is lower, the mic can be placed 
further away for a richer, fuller sound.
*Further miking techniques may be found on our website at www.audixusa.com
FREQUENCY / POLARS:
DIMENSIONS (mm):
D2
Transducer Type   
                  Dynamic
Frequency Response                    80 Hz  - 18 kHz 
Polar Pattern        
             Hypercardioid 
Output Impedance                                 250 ohms 
Sensitivity                                        1.2 mV / Pa @ 1k
Capsule Technology 
               VLM Type B
Off Axis Rejection                                   >30 dB
Maximum SPL                                   ≥144 dB                       
Power Requirements                               None
Connector 
                         Switchcraft® or Audix male
                                                           XLR connector
Polarity                               Positive pressure on diaphragm  
 
                           produces positive voltage on pin 2 
 
                                  relative to pin 3 of output 
                                                           XLR connector
Housing / Finish                       Machined Aluminum /  
                                                         Black Hard Coat 
Weight                                            128 g / 4.5 ounces 
Length                                          100 mm / 3.9 inches
SERVICE AND WARRANTY:
This microphone is under warranty for a period of 5 years from 
any and all manufacturing defects. Should your microphone 
fail in any way, please contact the Audix Service department 
at 503-682-6933. A Return Authorization number is required 
before returning any products.
CARE AND MAINTENANCE:
The D2 is manufactured to exacting specs with roadworthy construction. 
However, the capsule is highly sensitive and should be handled with care. 
Avoid extreme temperatures and be sure to store your microphone in the 
pouch provided when not in use. Moisture of any kind can adversely affect 
the sound and performance of your microphone. 
***All specifications subject to change without notice.
www.audixusa.com 
503-682-6933 Fax: 503-682-7114 
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
AUDIX WARRANTY REGISTRATION FORM
Please Check all that apply:
    Male      Female
Age: 
 
Occupation:  
Primary Instruments:       Product to be used for:    
    18 or Under 
   Musician   
   Vocal 
 
        Pro live sound
    19-25   
   Producer   
   Guitar / Bass 
        Pro recording
    26-35   
   Sound Eng. 
   Drums   
        Home recording
    36-45   
   Radio/TV   
   Keyboard  
        Rehearsal
    46-55    
   Production 
   Brass 
 
        Installation
    55 +  
 
   Other _______ 
   Woodwinds 
        School
 
 
 
 
   Strings   
        House of Worship
How did you hear about Audix?  
 
   Other ___________          Other ___________
   Magazine Ad            Online Ad  
   On-line Store            Friend                               Do you own other Audix Products?      Yes      No
   Salesman                 Other __________            Model(s) ________________________________
 
 
 
                  Have you visited the Audix website?     Yes       No  
Please register your product online at www.audixusa.com or mail this form to:
Audix Microphones P.O. Box 4010 Wilsonville, OR 97070
Name:________________________________ Model:___________________
Company:_____________________________ Serial Number:_____________
Address:______________________________ Store:____________________
City:_________________________________  Store Location:_____________
Prov./State:___________ Zip:_____________ Purchase Date:_____________
Phone: (     )___________________________ Signature:_________________
Email:________________________________ Date:____________________ 
1.1