Da-Lite ViewShare Advantage Electrol 24094LS プリント
製品コード
24094LS
SUGGESTED SPECIFICATIONS: projection screen(s),
(H) x (W), electrically operated 120 volt (60Hz), not
more than 2.4 amp with a quick connect male plug-in connector on the motor.
Shall have specially designed motor mounted inside the roller, to be three wire
with ground, quick reversal type, oiled for life, with automatic thermal overload
cutout, integral gears, capacitor and an electric brake to prevent coasting. To
have preset but adjustable limit switches to automatically stop picture surface
in the “up” and “down” positions. Junction box shall be externally integrated
into the housing making it possible to install the housing and wire to the
building’s electrical system during construction. The junction box shall contain
a quick connect interface that is mounted in the housing for easy plug-in
connection to the motorized fabric and roller assembly. The roller to be of rigid
metal. The motorized fabric and roller assembly to be installed in the case at
the factory. Roller mounting brackets to be adjustable to allow centering or
offsetting of the screen within the case. Screen to be designed for left or right-
hand motor installation. Screen fabric to be flame retardant and mildew
resistant fiberglass with black masking borders standard. Custom aluminum
(H) x (W), electrically operated 120 volt (60Hz), not
more than 2.4 amp with a quick connect male plug-in connector on the motor.
Shall have specially designed motor mounted inside the roller, to be three wire
with ground, quick reversal type, oiled for life, with automatic thermal overload
cutout, integral gears, capacitor and an electric brake to prevent coasting. To
have preset but adjustable limit switches to automatically stop picture surface
in the “up” and “down” positions. Junction box shall be externally integrated
into the housing making it possible to install the housing and wire to the
building’s electrical system during construction. The junction box shall contain
a quick connect interface that is mounted in the housing for easy plug-in
connection to the motorized fabric and roller assembly. The roller to be of rigid
metal. The motorized fabric and roller assembly to be installed in the case at
the factory. Roller mounting brackets to be adjustable to allow centering or
offsetting of the screen within the case. Screen to be designed for left or right-
hand motor installation. Screen fabric to be flame retardant and mildew
resistant fiberglass with black masking borders standard. Custom aluminum
slat bar with integrated 1080P camera adds weight and maintains vertical
tension on the screen surface.. The cable guide system attached to the slat
and screen case provides routing and management for camera USB cable.
Provided USB to CAT5 powered extender allows the use of up to 200 ft. of
CAT5 cable. The CAT5 cable plugs into the Cat 5 to USB extender mounted in
the case. It is accessible from the motor end of the case. Heavy duty metal
end caps shall protect the ends of the slat. Top, front and back of case to be
made of extruded aluminum powder coated white. End caps to be of heavy
gauge steel, powder coated white. Bottom of case to have a removable access
door. Door to be of extruded aluminum powder coated white. Bottom of case
to be self-trimming, with a built-in flange around the bottom of the case. To be
complete with integrated low voltage control unit and three position control
switch and cover plate. A USB remote speaker/microphone combination is
included. Suitable for use in environmental air space in accordance with
section 300-22 (c) of the National Electric Code, and sections 2-128, 12-010 (3)
and 12-100 of the Canadian Electrical Code, part 1, CSA C22.1. Screen to be
listed by Underwriters Laboratories.
tension on the screen surface.. The cable guide system attached to the slat
and screen case provides routing and management for camera USB cable.
Provided USB to CAT5 powered extender allows the use of up to 200 ft. of
CAT5 cable. The CAT5 cable plugs into the Cat 5 to USB extender mounted in
the case. It is accessible from the motor end of the case. Heavy duty metal
end caps shall protect the ends of the slat. Top, front and back of case to be
made of extruded aluminum powder coated white. End caps to be of heavy
gauge steel, powder coated white. Bottom of case to have a removable access
door. Door to be of extruded aluminum powder coated white. Bottom of case
to be self-trimming, with a built-in flange around the bottom of the case. To be
complete with integrated low voltage control unit and three position control
switch and cover plate. A USB remote speaker/microphone combination is
included. Suitable for use in environmental air space in accordance with
section 300-22 (c) of the National Electric Code, and sections 2-128, 12-010 (3)
and 12-100 of the Canadian Electrical Code, part 1, CSA C22.1. Screen to be
listed by Underwriters Laboratories.
SPECIFICATION DATA
HDTV (16:9) Format Dimensions
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
45" x 80"
114 x 203
92"
234
891⁄2"
227
75
34
52" x 92"
132 x 234
106"
269
1011⁄2"
258
88
39.9
54" x 96"
137 x 244
110"
279
1051⁄2"
268
89
40.4
58" x 104"
147 x 264
119"
302
1131⁄2"
288
95
43.1
65" x 116"
165 x 295
133"
338
1251⁄2"
319
98
44.5
Wide (16:10) Format Dimensions
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
50" x 80"
127 x 203
94"
239
891⁄2"
227
75
34
571⁄2" x 92"
146 x 234
109"
277
1011⁄2"
258
88
39.9
60" x 96"
152 x 244
113"
287
1051⁄2"
268
89
40.4
65" x 104"
165 x 204
123"
312
1131⁄2"
288
95
43.1
69" x 110"
175 x 279
130"
330
1191⁄2"
304
97
44
721⁄2" x 116"
184 x 295
137"
348
1251⁄2"
319
100
45
*Case length does not include flange
ViewShare
™
Advantage
®
Electrol
®
Automatic Electric Projection Screen Model with Built-In Videoconferencing