Da-Lite ViewShare Tensioned Advantage Electrol 110" 24017LS プリント
製品コード
24017LS
SUGGESTED SPECIFICATIONS: projection screen(s),
(H) x (W), electrically operated 120 volt (60 Hz) not
more than 2.4 amp. with a quick connect male plug-in connector on the motor.
Shall have specially designed motor mounted inside the roller, to be three wire
with ground, quick reversal type, oiled for life, with automatic thermal overload
cutout, integral gears, capacitor and an electric brake to prevent coasting. To
have preset but adjustable limit switches to automatically stop picture surface
in the “up” and “down” positions. Junction box shall be externally integrated
into the housing making it possible to install the housing and wire to the
building’s electrical system during construction. The junction box shall contain
a quick connect interface that is mounted in the housing for easy plug-in
connection to the motorized fabric and roller assembly. The motorized fabric
and roller assembly to be installed in the case at the factory. The fabric roller to
be of rigid aluminum. Screen to be designed for left or right-hand motor
installation. Screen fabric to be seamless, flame retardant and mildew resistant
vinyl with black masking borders standard. Each side of the fabric to have tab
guide cable system to maintain even lateral tension and hold surface flat.
Custom aluminum slat bar with integrated 1080P camera adds weight and
(H) x (W), electrically operated 120 volt (60 Hz) not
more than 2.4 amp. with a quick connect male plug-in connector on the motor.
Shall have specially designed motor mounted inside the roller, to be three wire
with ground, quick reversal type, oiled for life, with automatic thermal overload
cutout, integral gears, capacitor and an electric brake to prevent coasting. To
have preset but adjustable limit switches to automatically stop picture surface
in the “up” and “down” positions. Junction box shall be externally integrated
into the housing making it possible to install the housing and wire to the
building’s electrical system during construction. The junction box shall contain
a quick connect interface that is mounted in the housing for easy plug-in
connection to the motorized fabric and roller assembly. The motorized fabric
and roller assembly to be installed in the case at the factory. The fabric roller to
be of rigid aluminum. Screen to be designed for left or right-hand motor
installation. Screen fabric to be seamless, flame retardant and mildew resistant
vinyl with black masking borders standard. Each side of the fabric to have tab
guide cable system to maintain even lateral tension and hold surface flat.
Custom aluminum slat bar with integrated 1080P camera adds weight and
maintains vertical tension on the screen surface. The cable guide system
attached to the slat and screen case ensures routing and management for
camera USB cable. Provided USB to CAT5 powered extender allows the use of
up to 200ft of CAT5 cable. The CAT5 cable plugs into the CAT5 to USB
extender mounted in the case. It is accessible from the motor end of the case.
The ends of the slat to be protected by heavy duty plastic caps enclosing a
preset adjustable mechanism for screen tensioning. Top, front and back of
case to be made of extruded aluminum powder coated white. End caps to be
of heavy gauge steel powder coated white. Bottom of case to have a
removable access door. Door to be of extruded aluminum powder coated
white. Bottom of case to be self-trimming, with a built-in flange around the
bottom of the case. To be complete with integrated low voltage control unit
and three position control switch and cover plate. A USB remote speaker/
microphone combination is included. Suitable for use in environmental air
space in accordance with section 300-22 (c) of the National Electric Code, and
sections 2 -128, 12-010 (3) and 12-100 of the Canadian Electrical Code, part 1, CSA
C22.1. Screen to be listed by Underwriters Laboratories.
attached to the slat and screen case ensures routing and management for
camera USB cable. Provided USB to CAT5 powered extender allows the use of
up to 200ft of CAT5 cable. The CAT5 cable plugs into the CAT5 to USB
extender mounted in the case. It is accessible from the motor end of the case.
The ends of the slat to be protected by heavy duty plastic caps enclosing a
preset adjustable mechanism for screen tensioning. Top, front and back of
case to be made of extruded aluminum powder coated white. End caps to be
of heavy gauge steel powder coated white. Bottom of case to have a
removable access door. Door to be of extruded aluminum powder coated
white. Bottom of case to be self-trimming, with a built-in flange around the
bottom of the case. To be complete with integrated low voltage control unit
and three position control switch and cover plate. A USB remote speaker/
microphone combination is included. Suitable for use in environmental air
space in accordance with section 300-22 (c) of the National Electric Code, and
sections 2 -128, 12-010 (3) and 12-100 of the Canadian Electrical Code, part 1, CSA
C22.1. Screen to be listed by Underwriters Laboratories.
SPECIFICATION DATA
HDTV (16:9) Format Dimensions
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
45" x 80"
114 x 203
92"
234
96"
244
92
41.7
52" x 92"
132 x 234
106"
269
1081⁄2"
276
99
44.9
54" x 96"
137 x 244
110"
279
113"
287
104
47.2
58" x 104"
147 x 264
119"
302
1211⁄2"
309
114
51.7
65" x 116"
165 x 295
133"
338
1341⁄2"
342
135
61.2
Wide (16:10) Format Dimensions
Viewing Area (H x W)
Nominal Diagonal
Overall Length of Case*
Approx. Ship. Wt.
In.
Cm
In.
Cm
In.
Cm
Lbs.
Kg
50" x 80"
127 x 203
94"
239
961⁄2"
245
92
41.7
571⁄2" x 92"
146 x 234
109"
277
1091⁄2"
278
111
50.3
60" x 96"
152 x 244
113"
287
114"
290
104
47.2
65" x 104"
165 x 264
123"
312
1221⁄2"
311
114
51.7
69" x 110"
175 x 279
130"
330
129"
328
125
56.7
721⁄2" x 116"
184 x 295
137"
348
1351⁄2"
344
135
61.2
*Case length does not include flange
ViewShare
™
Tensioned Advantage
®
Electrol
®
Automatic Electric Projection Screen Model with Built-In Videoconferencing