Led Lenser SEO 7R 6107-R ユーザーズマニュアル

02

English 

 Page 02-06

GB

We are delighted that you have purchased one 

of our products.

These are usage instructions to help you 

familiarise yourself with your new purchase. 

All the documents accompanying the product 

must be read attentively before using the 

product, preserved carefully and if the product 

is transferred to a third party, the documents 

must be handed over as well. This ensures that 

maximum benefit is drawn from the product 

and questions from users are anticipated 

before they arise.

Above all, comply with the warnings and safety 

instructions and dispose of the packaging 

material properly.

Your LED LENSER SEO 7R headlamp with the 

item no. 6107-R (item no. 6007-R: No TEST IT 

function ) is packaged with a TEST IT function. 

This allows users to test the brightness while 

the product is still in the package. For testing, 

simply push the yellow TEST IT button on the 

front of the package.  When testing, please do 

not look directly into the light.

The TEST IT button is connected to the battery 

housing of the SEO 7R via two wires and should 

be removed prior to use.  

To remove the TEST IT button and wires, 

open the battery housing and remove the 3 

x AAA batteries (see also “Changing of the 

Accumulator-Pack / NiMH-Accumulator / 

Alkaline batteries” further below).  Separate 

the two TEST IT button wires from the battery 

housing by pulling on each wire until it releases 

from the battery housing.  Insert the 3 x AAA 

batteries respectively accumulators noting 

the correct polarity. Close the battery housing. 

Please dispose and recycle the packaging and 

TEST IT button with the wires according to the 

local regulations.

LED LENSER

6007-R 

LED LENSER® SEO 7R

6107-R 

LED LENSER® SEO 7R (Blister)

Version of the operating manual: 1.1

- 1 x Accumulator-Pack (scope of delivery of 

   6007-R and 6107-R) or 

- 3 x Alkaline batteries AAA/LR03/Micro (1.5 V 

   DC) (scope of delivery of 6107-R) or 

- 3 x NiMH-Accumulator AAA/LR03/Micro (1.2 

   V DC) (not scope of delivery)

In the upper part of the headlamp housing of 

the SEO 7R, between battery box and the part 

with the reflector lens, there is the switch 

button. This switch button is used to turn 

the SEO 7R on. It is also used to activate the 

various Light Programs and Lighting Functions 

(see section 5) and to switch between white 

light and red light (see Point 5). In addition, 

you can also activate the “Transport Lock” (see 

Point 7).

In the front, narrower region of the headlamp 

housing is the reflector lens through which the 

light of the white LED (see Point 5.1) is focused. 

The reflector lens is held by a plastic ring. You 

can rotate that plastic ring using two fingers, 

and thus adjust the focus quickly and easily. 

This so-called Speed Focus allows to adjust 

the angle of the white light beam continuously.

Depending on whether you want to illuminate 

an area in the distance or in front of you, you 

also can adjust the angle of light beam to the 

horizontal. For this you can simply tilt the part 

of the head lamp, which contains the reflector 

lens and the white LED. The screening allows 

using also intermediate positions.

The SEO 7R is equipped with our Smart 

Light Technology (SLT). Thanks to the use 

of a microcontroller, the light output of the 

LED can be controlled and the user can use 

various Light Programs and Light Functions. 

By using a single switch it was possible to 

design the interface to be simple and user-

friendly. The SEO 7R can give the user light 

in different ways. There are thus two Energy 

Modes, two Light Programs and a number of 

Light Functions available. To switch the pocket 

torch on and off and to select the various Light 

Functions etc., the switch (see Point 2) has to 

be used. 

What basically applies is that the brightness 

of the SEO 7R is monitored by the in-built 

temperature control unit.

In the SEO 7R are two LEDs (LED = 

Light 

Emitting Diode) installed.

The white LED is very strong, ideal for normal 

use, for example if the Speed Focus or the 

adjustment of the angle of light beam to the 

horizontal should be used. This very bright 

white light might be not good when your eyes 

have become accustomed through the so-

called dark adaptation to low ambient light. 

Otherwise than with the use of the white light, 

it remains the current adjustment of the eye 

to low brightness obtained when the red light 

of the second LED is used. The focus and the 

angle of the light to the horizontal of the red 

LED, which is located laterally next to the 

reflector-lens, can not be adjusted.

In order to switch between the white and the 

red LED, when the SEO 7R is off, press and 

hold the switch button for 2 seconds. The 

head lamp will change from red to white or 

from white to red, and then release the switch 

button before the lights go out, because if you 

press too long the switch button you activate 

the "Transport Lock“ (see section 7)!

The points below deal with the Light Functions 

of the white LED (Light Program White / Point 

5.1) and the red LED (Light Program "Red Night 

Vision“ / Point 5.2).

If the Lighting Program White is enabled (see 

Point 5), you can use the white, focusable light 

of the head lamp.

When the switch button is pressed, if the SEO 

7R is off, the head lamp glows in the Light 

Function Power at full brightness. When you 

switch a second time within 2 seconds, the SEO