Led Lenser H14.2 7299 ユーザーズマニュアル

We are delighted that you have purchased one 

of our products.

These are usage instructions to help you 

familiarize yourself with your new purchase. 

All the documents accompanying the product 

must be read attentively before using the 

product, preserved carefully and if the product 

is transferred to a third party, the documents 

must be handed over as well. This ensures that 

maximum benefit is drawn from the product 

and questions from users are anticipated before 

they arise.

Above all, comply with the warnings and safety 

instructions and dispose of the packaging 

material properly.

Your LED LENSER H14.2 headlamp is packaged 

with a “TEST IT” function (item no. 7399). This 

allows users to test the brightness while the 

product is still in the package. For testing, 

simply push the yellow TEST IT button on the 

front of the package.  When testing, please do 

not look directly into the light.

The TEST IT button is connected to the battery 

housing of the H14.2 via two wires and should 

be removed prior to use.  

To remove the “TEST IT” button and wires, 

open the battery housing and remove the 4XAA 

battery (see also “Changing of the alkaline 

battery” further below).  Separate the two “TEST 

IT” button wires from the battery housing by 

pulling on each wire until it releases from the 

battery housing.  Insert the 4XAA batteries and 

noting the correct polarity. Close the battery 

housing. Please dispose and recycle the 

packaging and “TEST IT” button with the wires 

according to the local regulations.

7299, 

LED LENSER® H14.2

7399, 

LED LENSER® H14.2 (blister)

Version of the operating manual: 1.3

- 4 x AA/LR06(1.5 V DC)

There are two switches on the H14.2.The 

front switch is located in the upper part of the 

headlamp housing. This button is used to turn 

the H14.2 ON/OFF. It is also used to activate the 

various Light Programs, Lighting Functions (see 

Section 5.1) and to active the “transport lock” 

functions (see Section 7).

The “Multi-function Wheel” switch is located 

on the backside in the upper part of the battery 

box. This allows you to adjust infinitely the 

brightness (down to 5 lm), flash rate and to 

change the light modes (see Section 5.1).

In the front, narrower region of the headlamp 

housing is the reflector lens through which the 

light of the LED is focusable. Adjust the focus 

by easily pulling and pushing the front cap. This 

is our patented “Speed Focus” system, which 

allows the adjustment of the light beam’s focus.

You also can adjust the hinge of the headlamp, 

depending on whether you want to illuminate 

an area in the distance or in front of you. For 

this, you simply tilt the part of the head lamp 

containing the reflector lens and the  LED. 

Smart Light Technology (SLT) is a program that 

consists of computer optimized microcontrollers 

which allows our products to have various 

lighting functions. The H14.2 is equipped with 

this technology and is therefore able to use 

various Light Programs and Functions with an 

interface that is simple and user friendly. With 

the Multi-function “Wheel” switch on the back, 

the light intensity (down to 5 lm) and flashing 

rate (1–24Hz) is infinitely adjustable simply 

by rotating the switch. By pressing the “Multi-

function Wheel” switch you can change the light 

mode.

The H14.2 is equipped with one LED (Light 

Emitting Diode). The white LED is very strong 

and ideal for normal use. For example if the 

Speed Focus or the adjustment of the angle of 

light beam to the horizontal should be used.

The boost mode of H14.2 can be turned on when 

the flashlight is off and then pushing the front 

switch for approx. 5 seconds. Release the switch 

when the boosted light is on otherwise the 

product will enter “transport lock” (see Section 

7).

In H14.2, there are three different modes (Easy 

Low, Easy Power, Signal). The default mode is 

the Easy Low

When the product is off, press the “Multi-function 

Wheel” switch on the back for 5 second. It will 

achieve transition mode. Then the LED will blink 

once (3Hz) to indicate that it is mode one; then 

blink twice for mode two; and finally blink thrice 

for mode three.

a) Light Mode one - Easy Low: when the product 

is off, firmly press the front button until it blinks 

once. The LED will glow at its lowest brightness 

(light function: Low Power). A second touch 

to the button on top of the lamp will turn ion 

the lamp to its full brightness (light function: 

Power), and third touch will turn the lamp off.

b) Light Mode two - Easy Power: when the 

product is off, firmly press the front button until 

it blinks twice. The LED will glow at its fullest 

brightness (light function: Power). A second 

touch to the button on top of the lamp will 

turn on the lamp to its lowest brightness (light 

function: Low Power), and third touch will turn 

the lamp off.

c) Light Mode three - Signal: when the product 

is off, firmly press the front button until it blinks 

thrice. The LED will glows with full brightness 

(light function: Power). A second touch to the 

button on top of the lamp will start the strobe (12 

Hz) (light function: Pulse), and a third touch will 

turn the lamp off. The speed at which the strobe 

will blink can be adjusted by turning the “Multi-

function Wheel” switch on the back. 

Note: In the low power- and power- function, 

you can adjust the brightness stepless by 

turning the multi-function "Wheel" switch (

Dim- 

02

English 

 Page 02-04

GB