Technoline Funk-Wetterstation WS 6750 Wireless Weather Station WS 6750 ユーザーズマニュアル
製品コード
WS 6750
1. 12 hour history of pressure 2. Air pressure data 3. Freeze 4. Weather 5. Bar of air pressure
6. Air pressure trend 7. Indoor low battery 8.Outdoor low battery 9. Channel 10. RF symbol
11. Temperature alert 12. Outdoor temperature trend 13. Indoor temperature trend
14. Outdoor humidity trend 15. Feel-good indicator 16. Indoor humidity trend 17. Week 18. Day of Week
19. Alarm 20. Month 21. Time 22. Summer time 23. Date 24. Moon set 25. Moon Rise 26. Moon Phase
27. Cities 28. Sun set 29. Sun rise A. MODE B. UP C. DOWN D. HISTORY E. CHANNEL F.
SNOOZE/LIGHT G. RESET
Initial Operation
•
Open the battery compartment located on the rear side of the devices. Place the batteries in
the battery compartment. Observe the shown polarity.
the battery compartment. Observe the shown polarity.
•
The altitude flashing , please use “
+
++
+
“, “
----
“to set the altitude of your position, then press
“HISTORY”, weather symbol flashing, pls use “
+
“, “
-
“ to choose the weather .
•
The station is now connecting to the outdoor sensor. This process takes about 3 minutes.
Then the display shows the outdoor temperature and humidity, in case of failure of reception ,
pls press“CHANNEL“for more than 3 seconds to receive again.
Then the display shows the outdoor temperature and humidity, in case of failure of reception ,
pls press“CHANNEL“for more than 3 seconds to receive again.
•
the automatic receiving of the DCF radio signal begins after 3 minutes of outdoor reception.
•
This RCC reception process is going on,the flashing symbol “radio tower“ appears in the time
display area at the same time.
display area at the same time.
•
Once radio signal receiving is successful, the display shows the symbol “radio tower“
continuously. No flashing.
continuously. No flashing.
If, due to bad reception, or no RCC automatic time reception is possible, follow the steps below
manually.
manually.
Reception of radio controlled signal
•
DCF radio signal search starts automatically about 3 minutes after battery exchange. The
“radio tower” signal is flashing.
“radio tower” signal is flashing.
•
Press“+“ “-“ for more than 3 seconds to enter or quit the Radio controlled signal reception
•
The clock synchronizes with the DCF radio signal automatically and daily from AM 1:00 to
3:00 to correct potential time deviations each hour. If the synchronization is unsuccessful
(“radio tower“ symbol disappears), a further synchronization attempt is made From 4:00 and
5:00 until success. This process is repeated up until 5:00 AM. If still not success, daily
reception stop.
3:00 to correct potential time deviations each hour. If the synchronization is unsuccessful
(“radio tower“ symbol disappears), a further synchronization attempt is made From 4:00 and
5:00 until success. This process is repeated up until 5:00 AM. If still not success, daily
reception stop.
Information
•
Flashing “radio tower” symbol stands for DCF radio signal reception started.
•
Continuous “radio tower” symbol stands for DCF radio signal reception successful.
•
Please observe a minimal distance of 2.5m to sources of interference such as televisions or
computer screens.
computer screens.
•
The radio signal reception is weaker in rooms with concrete walls (e.g. in the basement) and
in office buildings. For extreme cases, please put the clock near a window.
in office buildings. For extreme cases, please put the clock near a window.
•
There are less atmospheric disturbances at night. A radio time signal reception is usually
possible at that time. One synchronisation per day is sufficient to keep the time display
accuracy at 1 second.
possible at that time. One synchronisation per day is sufficient to keep the time display
accuracy at 1 second.