Bosch 2607001409 Universal cutting oil - 100 ml 2607001409 データシート
製品コード
2607001409
Page 3/6
Safety data sheet
according to 1907/2006/EC, Article 31 and 453/2010/EC
Printing date 04.07.2013
Revision: 04.07.2013
Version number 4
Trade name: Drilling and Cutting Oil 15 BOSCH & HILTI
(Contd. of page 2)
37.0.1
Further information about storage conditions:
Protect from heat and direct sunlight.
Optimal storage temperature between -15 °C and +40 °C.
Duration of storage: In original container, at least 3 years.
7.3 Specific end use(s) No further relevant information available.
Protect from heat and direct sunlight.
Optimal storage temperature between -15 °C and +40 °C.
Duration of storage: In original container, at least 3 years.
7.3 Specific end use(s) No further relevant information available.
8 Exposure controls/personal protection
Additional information about design of technical facilities: No further data; see item 7.
8.1 Control parameters
Ingredients with limit values at the workplace: TLV value (oil mist) CH: 5 mg/m³
Additional information: The lists valid during the making were used as basis.
Ingredients with limit values at the workplace: TLV value (oil mist) CH: 5 mg/m³
Additional information: The lists valid during the making were used as basis.
8.2 Exposure controls
Personal protective equipment:
General protective and hygienic measures:
The usual precautionary measures are to be adhered to when handling chemicals.
Respiratory protection: Not required.
Material of gloves
Suitable protective gloves: Nitrile gloves, minimum thickness of 0.3 mm, e.g. Ultranitril type 491.
Corresponds to the standards DIN/EN 374-2 and 374-3.
Penetration time of glove material
The exact breaktrough time has to be found out by the manufacturer of the protective gloves and has to
be observed.
Eye protection: Eye protector with side protection (framed eyeglasses) EN 166.
Body protection: Protective work clothing
Personal protective equipment:
General protective and hygienic measures:
The usual precautionary measures are to be adhered to when handling chemicals.
Respiratory protection: Not required.
Material of gloves
Suitable protective gloves: Nitrile gloves, minimum thickness of 0.3 mm, e.g. Ultranitril type 491.
Corresponds to the standards DIN/EN 374-2 and 374-3.
Penetration time of glove material
The exact breaktrough time has to be found out by the manufacturer of the protective gloves and has to
be observed.
Eye protection: Eye protector with side protection (framed eyeglasses) EN 166.
Body protection: Protective work clothing
*
9 Physical and chemical properties
9.1 Information on basic physical and chemical properties
General Information
Appearance:
General Information
Appearance:
Form:
Fluid
Colour:
Yellow
Odour:
Pleasant
Change in condition:
Melting point/Melting range: Not applicable
Boiling point/Boiling range: > 300 °C (DIN 51751)
Drip point:
Boiling point/Boiling range: > 300 °C (DIN 51751)
Drip point:
Not applicable
Pour point:
- 21 °C. (ISO 3016)
Flash point:
210 °C (ISO 2592)
Ignition temperature:
Not applicable
Self-igniting:
Product is not selfigniting.
Danger of explosion:
Product does not present an explosion hazard.
Density at 20 °C:
0.90 g/cm³ (DIN 51757)
Solubility in / Miscibility with
water:
Insoluble.
Viscosity:
Kinematic:
15 mm²/s @ 40 °C (ISO 3104)
(Contd. on page 4)
GB