Microchip Technology MCU PIC10F322T-I/OT SOT-23-6 MCP PIC10F322T-I/OT データシート
製品コード
PIC10F322T-I/OT
PIC10(L)F320/322
DS41585A-page 180
Preliminary
2011 Microchip Technology Inc.
24.8
AC Characteristics: PIC10(L)F320/322-I/E
FIGURE 24-5:
CLOCK TIMING
TABLE 24-1:
CLOCK OSCILLATOR TIMING REQUIREMENTS
TABLE 24-2:
OSCILLATOR PARAMETERS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Operating temperature
-40°C
T
A
+125°C
Param
No.
Sym.
Characteristic
Min.
Typ†
Max.
Units
Conditions
OS01
F
OSC
External CLKIN Frequency
(1)
DC
—
20
MHz
EC mode
OS02
T
OSC
External CLKIN Period
(1)
31.25
—
ns
EC Oscillator mode
OS03
T
CY
Instruction Cycle Time
(1)
200
T
CY
DC
ns
T
CY
= 4/F
OSC
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
tested.
Note 1:
Instruction cycle period (T
CY
) equals four times the input oscillator time base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at “min” values with an external clock applied to CLKIN pin. When an external
clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at “min” values with an external clock applied to CLKIN pin. When an external
clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
Standard Operating Conditions (unless otherwise stated)
Operating Temperature
Operating Temperature
-40°C
T
A
+125°C
Param
No.
Sym.
Characteristic
Freq.
Tolerance
Min.
Typ†
Max.
Units
Conditions
OS08
HF
OSC
Internal Calibrated HFINTOSC
Frequency
Frequency
(1)
±2%
±3%
±3%
—
—
—
16.0
16.0
16.0
—
—
—
MHz
MHz
MHz
0°C
T
A
+60°C, V
DD
2.5V
60°C
T
A
85°C, V
DD
2.5V
±5%
—
16.0
—
MHz
-40°C
T
A
+125°C
OS09
LF
OSC
Internal LFINTOSC Frequency
—
—
31
—
kHz
-40°C
T
A
+125°C
OS10*
T
IOSC
ST
HFINTOSC
Wake-up from Sleep Start-up Time
Wake-up from Sleep Start-up Time
—
—
5
8
s
*
These parameters are characterized but not tested.
†
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
tested.
Note 1:
To ensure these oscillator frequency tolerances, V
DD
and V
SS
must be capacitively decoupled as close to the device as
possible. 0.1
F and 0.01 F values in parallel are recommended.
CLKIN
CLKR
Q4
Q1
Q2
Q3
Q4
Q1
OS02
OS03
(CLKROE = 1)