Insys Modem 56k 4.1 m/UL 11-02-01-01-40.022 ユーザーズマニュアル
製品コード
11-02-01-01-40.022
INSYS Modem 56k UL
Configiration
Juni 05
15
4.6.2 Alarm Actions
SMS transmission from the analog telephone network is routed by special gateway
numbers of the network providers. These Service Center Numbers and the protocol (PET or
UCP) are preconfigured for German GSM networks.
numbers of the network providers. These Service Center Numbers and the protocol (PET or
UCP) are preconfigured for German GSM networks.
4.6.2.1 Simple alarm
Alarm notifications consist of an alarm text of a maximum of 160 characters. The notifi-
cation is transmitted to a modem over data connection or to mobile phone by SMS.
Alarm notifications consist of an alarm text of a maximum of 160 characters. The notifi-
cation is transmitted to a modem over data connection or to mobile phone by SMS.
4.6.2.2 Impulse alarm
With impulse alarm active alarm notification are composed from 120 characters com-
mon text for all alarms and 80 characters individual alarm text – the first 160 characters
are transmitted by SMS. The alarm index is specified by the number of pulses. If more
than 10 pulses are applied message 10 is transmitted.
The notifications are transmitted to mobile phones by SMS. All recipients must be lo-
cated within the network of the same GSM provider.
Attention: alarm number 1 must be configured in any case to activate impulse alarming.
With impulse alarm active alarm notification are composed from 120 characters com-
mon text for all alarms and 80 characters individual alarm text – the first 160 characters
are transmitted by SMS. The alarm index is specified by the number of pulses. If more
than 10 pulses are applied message 10 is transmitted.
The notifications are transmitted to mobile phones by SMS. All recipients must be lo-
cated within the network of the same GSM provider.
Attention: alarm number 1 must be configured in any case to activate impulse alarming.
4.6.2.3 Collective fax massage
In addition all alarm notifications can be sent to a central fax number for logging.
In addition all alarm notifications can be sent to a central fax number for logging.
4.6.2.4 Connection
If a connection can not be established 3 dial attempts with 10 seconds breaks in between
are executed. Alarm notification is aborted if no connection was successful. A new con-
nection is only initiated when the alarm input is opened and closed again.
Data connection to a modem can remain after the transmission of the notification with
the selection data connection, keep connection. After fax or SMS transmission the con-
nection is closed by the modem in any case.
A dial prefix is necessary for the service center numbers only, not for the single target
numbers.
If a connection can not be established 3 dial attempts with 10 seconds breaks in between
are executed. Alarm notification is aborted if no connection was successful. A new con-
nection is only initiated when the alarm input is opened and closed again.
Data connection to a modem can remain after the transmission of the notification with
the selection data connection, keep connection. After fax or SMS transmission the con-
nection is closed by the modem in any case.
A dial prefix is necessary for the service center numbers only, not for the single target
numbers.
4.6.2.5 SMS in the fixed network
SMS gateways in the fixed network are supported by the latest firmware. SMS in the
fixed network can be transmitted as well to fixed telephones as to a fax or a e-mail ad-
dress. The following access data are from Deutsche Telekom:
Service-Center:
SMS gateways in the fixed network are supported by the latest firmware. SMS in the
fixed network can be transmitted as well to fixed telephones as to a fax or a e-mail ad-
dress. The following access data are from Deutsche Telekom:
Service-Center:
01930100
SMS to fax:
set prefix 99 ahead of fax device number
SMS to e-mail:
set recipient number to 8000 (SMS-e-mail gateway)
text message begins with e-mail address, followed by a space and
the message. Replace @ in the e-mail address by an asterisk *.
(Note: The common text must be empty or start with the e-mail
address for pulsed alarm.)
the message. Replace @ in the e-mail address by an asterisk *.
(Note: The common text must be empty or start with the e-mail
address for pulsed alarm.)