Atmel ATSAM3S-EK2 データシート
Atmel AVR2055
43
8348D-AVR-06/12
ii. Add paths to the folder containing the AVRGCC compiler to
the Path Windows environment variable. The compiler is
located in the
\extensions\Atmel\AVRGCC\3.3.1.27\AVRToolchain\bin
directory of the AVR Studio installation directory.
, if not already installed on the
PC
5. If the WSNRunner application will be used, see Section
instructions
6. Demonstration of OTAU functionality and programming devices with Serial
Bootloader require the Serial Bootloader package, which should be downloaded
from the Atmel website
9.2 Pre-built images
PS SDK for XMEGA devices. The user can load them into the STK600 board, as
described in Section
Table 9-3. Firmware images supplied with BitCloud PS for XMEGA.
Application
Platform
Location and filename
SE meter
XMEGA-STK600
./Evaluation Tools/SEDevice/SE_Meter_XMEGAA3_RF231.hex
SE in-premise display
XMEGA-STK600
./Evaluation Tools/SEDevice/SE_IPD1_XMEGAA3_RF231.hex
SE thermostat
XMEGA-STK600
./Evaluation Tools/SEDevice/SE_Thermostat_XMEGAA3_RF231.hex
SE energy service portal XMEGA-STK600
./Evaluation Tools/SEDevice/SE_ESP_XMEGAA3_RF231.hex
HA dimmer switch
XMEGA-STK600
./Evaluation Tools/HADevice/HA_DimmerSwitch_XMEGAA3_RF231.hex
HA dimmable light
XMEGA-STK600
./Evaluation Tools/HADevice/HA_DimmableLight_XMEGAA3_RF231.hex
HA occupancy sensor
XMEGA-STK600
./Evaluation Tools/HADevice/HA_OccupancySensor_XMEGAA3_RF231.hex
HA remote control
XMEGA-STK600
./Evaluation Tools/HADevice/HA_RemoteControl_XMEGAA3_RF231.hex
HA TC
XMEGA-STK600
./Evaluation Tools/HADevice/HA_TC_XMEGAA3_RF231.hex
HA thermostat
XMEGA-STK600
./Evaluation Tools/HADevice/HA_Thermostat_XMEGAA3_RF231.hex
Runner
XMEGA-STK600
./Evaluation Tools/Runner/Runner_XMEGAA3_RF212.hex
./Evaluation Tools/Runner/Runner_XMEGAA3_RF230B.hex
./Evaluation Tools/Runner/Runner_XMEGAA3_RF231.hex
./Evaluation Tools/Runner/Runner_XMEGAA3_RF230B.hex
./Evaluation Tools/Runner/Runner_XMEGAA3_RF231.hex
ZAppSI demo
XMEGA-STK600
./Evaluation Tools/Demo/SEMeter(hosted)_XMEGAA3.hex
./Evaluation Tools/Demo/SEMeter(hosted)_XMEGAA3.srec
./Evaluation Tools/Demo/SEMeter(hosted)_XMEGAA3.srec
SAM7X-EK
./Evaluation Tools/Demo/SEMeter(hosted)_SAM7X.bin
PC
./Evaluation Tools/Demo/SEMeter(hosted)_PC.exe
NOTE
Default images of reference devices are preconfigured to operate a network with
high-security mode on channel
0x0F
with Extended PAN ID
0xAAAAAAAAAAAAAAAA
.
9.3 Programming the boards
Firmware images can be loaded to the board using the following methods:
programming using JTAG either in IAR Embedded Workbrench or AVR Studio, and
programming with the Serial Bootloader package. Before the programming make sure
that fuse bits are configured correctly, as described in Section