Enda EUC942 PID-Controller EUC EUC942 データシート
製品コード
EUC942
Gasket
Depth
Panel cut-out
AL1
CNT/AL2
AN/SSR
UNIVERSAL CONTROLLER
EUC 942
ENDA
PV
SV
SET
ASET
CSET
98mm
96mm
104mm
99mm
90.5mm
90.5mm
57mm
Panel
50mm
1
2
Screw-terminal connections
DIMENSIONS
ENDA EUC942 is intended for installation in control panels. Make sure that the device is used only for intended purpose.
During an installation, all of the cables that are connected to the device
must be free of energy. The device must be protected against inadmissible humidity, vibrations, severe soiling and make sure
that the operation temperature is not exceeded. All input and output lines that are not connected to the supply network must
be laid out as shielded and twisted cables. These cables should not be close to the power cables or components.
that the operation temperature is not exceeded. All input and output lines that are not connected to the supply network must
be laid out as shielded and twisted cables. These cables should not be close to the power cables or components.
The
shielding must be grounded on the instrument side.
The
installation and electrical connections must be carried on by a qualified staff and must be according to the relevant locally
applicable regulations.
applicable regulations.
CONNECTION DIAGRAM
Note
) Panel thickness should be maximum 10mm.
: 1
2) If there is no 60mm free space at back side of the device,
it would be difficult to remove it from the panel.
Flush mounting
clamp
-While pressing both side of
the device in direction , push it
in direction .
in direction .
1
2
For removing the device from
the panel:
the panel:
Logic output of the instrument is not
electrically insulated from the
internal circuits. Therefore, when
using a grounding thermocouple, do
not connect the logic output
terminals to the ground.
electrically insulated from the
internal circuits. Therefore, when
using a grounding thermocouple, do
not connect the logic output
terminals to the ground.
1) Mains supply cords shall meet
the requirements of IEC 60227 or
IEC 60245.
2) In accordance with the safety
regulations, the power supply
switch shall bring the identification
of the relevant instrument and it
should be easily accessible by the
the requirements of IEC 60227 or
IEC 60245.
2) In accordance with the safety
regulations, the power supply
switch shall bring the identification
of the relevant instrument and it
should be easily accessible by the
Note
Holding screw
0.4-0.5Nm
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
by DOUBLE INSULATION.
For J-K-T-S-R type thermocouple :
Use suitable compensation cables. Don't use
Use suitable compensation cables. Don't use
jointed cables. Pay attention to the polarities
of the thermocouple cables as shown in the
figure right are connected to the .
figure right are connected to the .
For resistance thermometer :
When 2 wired Pt 100 is used, terminals 9
When 2 wired Pt 100 is used, terminals 9
and 10 must be short circuited.
Fuse should
be connected.
be connected.
184-253V AC
50/60Hz 7VA
50/60Hz 7VA
230V ,110V or 24V AC
Supply
Supply
switch
Cable size: 1,5mm²
Neutral
Line
SENSOR INPUT :
2
1
TC
-
+
-
+
9
8
10
8
Pt 100
0-20mA or
4-20mA input
4-20mA input
-
+
NOTE :
Fuse
F 100 mA
250V AC
SUPPLY :
9
Order Code
-
: EUC 42-
9
2- Modbus Option
RS........RS-485 Modbus communication
None....Don’t support RS-485 Modbus communication
None....Don’t support RS-485 Modbus communication
1- Supply Voltage
230VAC...230V AC
24VAC.....24V AC
SM...........9-30V DC / 7-24V AC
SM...........9-30V DC / 7-24V AC
110VAC...110V AC
1
2
SN: XXXXXXXXX
AL1
AC 250V 2A
RESISTIVE LOAD
1
8
2
9
7
14 15
6
13
3
10
4
11
5
12
ENDA
INDUSTRIAL ELECTRONICS
EUC942-230VAC-RS
PID UNIVERSAL CONTROLLER
PID UNIVERSAL CONTROLLER
230V
AC +10% -20%
50/60Hz 7V
A
OUT1 /
AL2 OUT
AC 250V 2A
RESISTIVE LOAD
+
-
Pt 100
TC
(mA
inp).
-
+
RS-485 COM.
RS- 485
ANL/SSR
OUT
B
A
+
-
SN: XXXXXXXXX
AL1
AC 250V 2A
RESISTIVE LOAD
1
8
2
9
7
6
3
10
4
11
5
12
ENDA
INDUSTRIAL ELECTRONICS
EUC942-24VAC
PID UNIVERSAL CONTROLLER
PID UNIVERSAL CONTROLLER
24V
AC ±10%
50/60Hz 7V
A
OUT1 /
AL2 OUT
AC 250V 2A
RESISTIVE LOAD
+
-
Pt 100
TC
(mA
inp).
ANL/SSR
OUT
+
-
E-mail : info@suran-elektronik.de
Internet : www.suran-elektronik.de
Internet : www.suran-elektronik.de
Tel.: +49 (0)7451 / 625 617
Fax: +49 (0)7451 / 625 0650
Fax: +49 (0)7451 / 625 0650
SURAN
Industrieelektronik
Dettinger Str. 9 / D-72160 Horb a.N
5./5
EUC942-E
-
+
9
8