Fanox D30/230V AC D30/230V AC D30/230V AC データシート
製品コード
D30/230V AC
Fig. 1
Fig. 2
2
1
3
4
5
6
7
8
9
6
7
8
9
10
11
12
13
11
12
13
• RELÉ DIFERENCIAL DE FALLOS A TIERRA
• EARTH FAULT DIFFERENTIAL RELAY
Dimensiones / Dimensions
8
7
6
5
4
3
2
9
10 11 12 13
1
*
El relé supervisa permanentemente el circuito toroidal-relé, si este se
interrumpe el relé dispara y enciende de forma intermitente el LED rojo.
**
El equipo dispone de doble circuito de medida lo que le confiere una
seguridad redundante. Si uno de estos circuitos se averiase el relé
seguiría midiendo correctamente por el otro. Esta situación es detectada
por la función auto-diagnostico de que dispone y señalizada mediante el
parpadeo del LED verde ON. Cuando se de esta improbable situación es
aconsejable sustituir el relé cuando sea posible.
INSTRUCCIONES DE SEGURIDAD
• Para evitar descargas eléctricas durante la instalación o manipulación
del relé, asegúrese de que no hay tensión en la línea ni tensión auxiliar.
• Comprobar que la tensión nominal es la correcta.
ESQUEMA DE CONEXIONES
• Cableado: Los esquemas se representan con el relé sin tensión de
alimentación conectada.
• Conectar el dispositivo de disparo (bobina de emisión, bobina de
mínima, contactor, etc.) según el siguiente cuadro.
Contactos de salida
Bornas conexión transformador
Bornas conexión transformador
toroidal CT-1
Botón de rearme
Botón de prueba
Ajuste sensibilidad
Botón de rearme
Botón de prueba
Ajuste sensibilidad
I
∆
n
Ajuste del tiempo de retardo
LED rojo
LED verde
Alimentación
Tipo de rearme
Selección lógica de disparo
Factor multiplicador de sensibilidad
Selección frecuencia de la red
LED rojo
LED verde
Alimentación
Tipo de rearme
Selección lógica de disparo
Factor multiplicador de sensibilidad
Selección frecuencia de la red
*
The relay constantly supervises the toroidal circuit-relay. Should this
become interrupted the relay trips and the red LED begins to flash.
**
The unit is equipped with a double measuring circuit providing
redundant safety. Should one of these circuits fail, the relay shall
continue measuring correctly via the other one. This situation is detected
by its self-diagnosis function and is signalled by means of the flashing
green LED ON. Should this improbable situation occur it is advisable to
replace the relay as soon as possible.
SAFETY INSTRUCTIONS
• To prevent electric discharges during the installation or handling of the
relay, ensure there is no voltage in the line and no auxiliary voltage.
• Check that the nominal voltage is correct.
CONNECTION DIAGRAM
• Wiring: The schematics show the relay with supply voltage disconnected.
• Connect the trip device (shunt trip coil, undervoltage trip coil, contactor,
etc.) according to the following table.
A
B
B
A
Output contacts
Connection terminals for toroidal
Connection terminals for toroidal
transformer CT-1
Reset push-button
Test push-button
Sensitivity adjustment
Reset push-button
Test push-button
Sensitivity adjustment
I
∆
n
Delay time adjustment
Red LED
Green LED
Supply
Reset type
Logic trip selection
Sensitivity multiplier factor
Network frequency selection
Red LED
Green LED
Supply
Reset type
Logic trip selection
Sensitivity multiplier factor
Network frequency selection
Prioridad de seguridad
Fig. 2
Fig. 1
Posit. P
Safety priority
Prioridad de servicio
Fig. 1
Fig. 2
Negat. N
Service priority
Bobina de mínima
Contactor
C
Bobina de emisión
Lógica de disparo
Undervoltage trip coil
Contactor
Shunt trip coil
Logic trip
C
C
C
D30
100
80
72,6
22,4
61,
5
22,5