ABUS Wireless water leak alarm Max. range (open field) 100 m FS-101 データシート
製品コード
FS-101
Radio Water Warning Device A
Version 01/09
Item-No. 75 12 89
°
1. Intended Use
The radio water warning device A serves for monitoring water level overflow. As soon as both
sensor-contacts touch the water a short-circuit arises and the radio water warning device A is
sending a signal to the radio alarm system.
sensor-contacts touch the water a short-circuit arises and the radio water warning device A is
sending a signal to the radio alarm system.
The power supply takes place over a 3V button cell type „CR2032“.
Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
risk of short circuits, fire, electric shock, etc.
No part of the product should be modified or reassembled. It is not authorized to use the device
if the housing is not completely shut.
if the housing is not completely shut.
All safety and assembly instructions must be observed without fail.
2. Contents
• Radio Water Warning Device A
• Operating instructions
• 1 x button cell type „CR2032“
• Operating instructions
• 1 x button cell type „CR2032“
3. Explanation of symbols
Ꮨ
The flash icon in a triangle is used to alert you to potential personal injury hazards
such as electric shock.
such as electric shock.
An exclamation mark in a triangle indicates important information in these operat-
ing instructions which are to be followed strictly.
ing instructions which are to be followed strictly.
☞
The „hand” symbol indicates special information and advice on operating the
device.
device.
4. Safety instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions!
Liability for any and all consequential damage is excluded!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions. The
warranty is voided in these cases.
these safety instructions!
Liability for any and all consequential damage is excluded!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions. The
warranty is voided in these cases.
Dear Customer, the following safety instructions are intended not only for the protection
of your health but also for the protection of the device. Please read carefully through the
following points:
of your health but also for the protection of the device. Please read carefully through the
following points:
a) General information
• If you are not sure when assembling, connecting and installing the device or if you have doubts
as of the mode of operation of the device, do not effect the assembly/connection/installation of
the device yourself, but rather contact a specialist.
the device yourself, but rather contact a specialist.
• The unauthorised conversion and/or modification of the product is inadmissible because of
safety and approval reasons (CE).
• The product is intended for dry indoor locations only. The electronic unit (the larger compo-
nents) must not became damp or wet, only the separated sensor (the smaller components)
may touch water.
may touch water.
• Keep the product out of the reach of children.
• Do not leave the packaging material lying around carelessly since it constitutes a danger to chil-
• Do not leave the packaging material lying around carelessly since it constitutes a danger to chil-
dren.
• Handle the product with care. It can be damaged through impact, blows, or accidental drops,
even from a low height.
b) Batteries and rechargeable batteries
• Keep batteries out of reach of children.
• Make sure you pay attention to correct polarity when inserting the (rechargeable) batteries.
• Do not leave (rechargeable) batteries lying about openly. There is a risk that the batteries may
• Make sure you pay attention to correct polarity when inserting the (rechargeable) batteries.
• Do not leave (rechargeable) batteries lying about openly. There is a risk that the batteries may
be swallowed by children or pets. If swallowed, consult a doctor immediately.
• Leaking or damaged (rechargeable) batteries in contact with the skin might cause acid burns,
therefore, use suitable protective gloves.
• Make sure that batteries/storage batteries are not short-circuited or thrown into fire. There is a
risk of explosion!
• Never disassemble batteries/storage batteries.
• Do not recharge normal batteries. There is a risk of explosion!
• In case of longer periods of non-use (e.g. during storage) remove the inserted (rechargeable)
• Do not recharge normal batteries. There is a risk of explosion!
• In case of longer periods of non-use (e.g. during storage) remove the inserted (rechargeable)
batteries to avoid damage by a leaking battery.
O P E R A T I N G I N S T R U C T I O N S
www.conrad.com
5. Assembly
☞
Please note that only the separated sensor (the smaller components) may
touch water. The electronic unit of the radio water warning device A (the larg-
er components) must not get damp or wet.
touch water. The electronic unit of the radio water warning device A (the larg-
er components) must not get damp or wet.
• Mount the electronic unit of the radio water warning device (the larger components) in such a
way, that the electronic unit does not contact water in case of a high water level.
• Mount the separated sensor with the free downward facing metal contacts at the preferred
height, at which the water level should be reported.
• This is highly recommended because of the given suction cups.
• Check the correct grip to ensure that the mounting place is suitable for suction cup mounting.
• Check the correct grip to ensure that the mounting place is suitable for suction cup mounting.
6. Training of the radio water warning device A on the
radio alarm system.
☞
Please consult the operation manual of your radio alarm system prior to train-
ing the radio water warning device A.
This way you will get a complete picture of the possible alarm zones on which
you can train the radio movement alarm.
ing the radio water warning device A.
This way you will get a complete picture of the possible alarm zones on which
you can train the radio movement alarm.
For training the radio movement alarm at the radio alarm system, just do the following:
Step
Action
Function
Note
1
Press the key
„PROG“ on your radio-
alarm system.
„PROG“ on your radio-
alarm system.
2
Give the
You arrive in the
3 x short bleep tone at the
four-digits
programming mode.
alarm service confirms to you
mastercode.
the correct code-input.
1 x long bleep tone indicates
an incorrect code-input.
1 x long bleep tone indicates
an incorrect code-input.
3
Press the
You arrive in the
As soon as you arrive in the
key 3 on the
programming mode for
programming mode,
alarm system.
Training new sensors.
the „Zone Status-LEDs“ are
shining or flashing on the
alarm system.
** Look for the explanation in
the next table.
shining or flashing on the
alarm system.
** Look for the explanation in
the next table.
4
Press the key
To select the correct
1, 2, 3, 4, 5, 6, 7, 8, 9
memory position,
or 0, depending,
for this, please note the
which memory position
table above.
you want to use.
5
Activate the
A spoken message
The settings are
radio water warning
confirms to you the
saved and the
device.
successfull training.
programming mode is exited.
** Meaning of the „Zones Status-LEDs“ from step 3 of the prior table:
„Zones Status-LED“.
Explanation:
Does not light up
At this zone no radio sensor was trained yet.
Single flashing
At this zone sensor 1 was already trained.
Double flashing
At this zone sensor 2 was already trained.
Single and subsequently
At this zone sensor 1 as well as sensor 2 were already
double flashing.
trained.