ABUS Wireless door alarm Max. range (open field) 100 m WD-101 データシート

°

The radio controlled door/window detector disposes of a magnetic contact, its activation being
reported to the radio controlled alarm control unit.

The power supply takes place by means of a 3V button cell (type CR2032). Mounting and oper-
ating the radio controlled door/window detector is only permitted in dry indoor locations. The
product must not get damp or wet!

Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.

No part of the product should be modified or reassembled. It is not authorized to use the device
if the housing is not completely closed.



• Radio controlled door/window detector
• Magnet
• Assembly material
• Operating instructions



The flash icon in a triangle is used to alert you to potential personal injury hazards
such as electric shock.



A triangle containing an exclamation mark indicates important information in these
operating instructions which are to be observed without fail.

☞

The “hand” symbol indicates special information and advice on operating the
device.



• If you are not sure when assembling, connecting and installing the device or if you have doubts

as of the mode of operation, do not effect the assembly/connection/installation yourself, but
rather contact a specialist.

• The unauthorised conversion and/or modification of the product is inadmissible because of

safety and approval reasons (CE).

• The product is intended for mounting and operating in dry, closed indoor locations only. The

product must not get damp or wet.

• Keep the product out of the reach of children.
• Do not leave the packaging material lying around carelessly since it constitutes a hazard to chil-

dren.

• Handle the product with care. It can be damaged through impact, blows, or accidental drops,

even from a low height.

• Batteries and rechargeable batteries must be kept out of the reach of children.
• Please observe the correct polarity, when inserting batteries/rechargeable batteries into

the unit.

• Do not leave batteries/rechargeable batteries lying about openly. There is a risk that they may

be swallowed by children or pets. If swallowed, consult a doctor immediately.

• Leaking or damaged (rechargeable) batteries in contact with the skin might cause acid burns,

therefore, use suitable protective gloves.

• Make sure that batteries/rechargeable batteries are not short-circuited or thrown into fire. There

is a risk of explosion!

• Never disassemble batteries/rechargeable batteries.
• Conventional batteries may not be recharged.. There is a risk of explosion!
• 

In case of longer periods of non-use (e.g. during storage) remove the inserted
batteries/rechargeable batteries to avoid damage by a leaking battery.



☞



Test the correct function first before screw assembling, to avoid unsightly „false“ holes.

• The radio controlled door/window detector consists of two

components, the magnet (the smaller component) and the
radio controlled door/window detector (the larger compo-
nent). 

Basically the radio controlled door/window detector is moun-
ted on the door frame (or e.g. window frame) and the mag-
net on the door (or e.g. window).    

• Make absolutely sure the bottom of the magnet is 8 mm

away from the bottom of the radio controlled door/window -
detector.

A higher or lower mounting reduces the range of the magnet,
the magnet must be mounted closer to the radio controlled
door/window detector!

The horizontal distance from the magnet to the radio con-
trolled door/window detector must be a maximum of 20 mm.
Ideal is a distance of approx. 10-15 mm.

To guarantee a better hold of the radio controlled door/win-
dow detector, we advise you, to use the mounting plate (A;-
see picture right) included in delivery.

• Apply the mounting plate (A) to the contemplated mounting

site and mark both drill-holes.

• Attach the mounting plate (A) with appropriate mounting

material. 

• Stick the two-sided adhesive tape (B) included in delivery

onto the mounting plate (A).

• Attach the radio controlled door/window detector (C).
• Now attach the magnet (pay attention to the distances!) by

means of the double-sided adhesive tape included in
delivery. 

Please also observe the instructions of your radio controlled alarm device when programming
the radio controlled door/window detector. 
You hereby get a general idea of the possible alarm zones the radio controlled door/window
detector can be programmed for.

To program the radio controlled door/window detector in the radio controlled alarm device,
please act as follows:

1

Push the button 
„PROG“ on your radio 
controlled alarm device.

2

Introduce  

You access the 

3 x short bleeps to the

four-digit 

programming mode.

Alarm device confirms

the master code.

the correct code input. 1 x
long bleep indicates an
incorrect code input.

3

Push the  

You access the 

As soon as you access

button 3 on the  

programming mode for  

programming mode

alarm device.

Programming new sensors. the „Zone Status LEDs“ 

on the alarm device light up
or blink. 
** see explanation in the fol-
lowing chart

4

Press the key  

To select the

1, 2, 3, 4, 5, 6, 7, 8, 9 

right memory,

or 0, depending on  

please observe the

which memory  

above chart.

you would like 
to use

5

Then activate  

A voice message

The settings are 

Radio controlled door/

confirmed by the

saved and the

window detector. 

successful programming.

programming mode is exit-
ed.