Accusplit AE2700 プリント

To record your distance and calories 

accurately, you will need to set your stride 

length and body weight. 

 (2740, 2790 

: Your stride length is the length of one 

of your steps, measured from “toe to toe.” 

To measure, walk 10 steps with your normal 

stride and measure the TOTAL DISTANCE 

from the toe of your starting step to the toe 

of your 10

th

 step (see diagram below). Divide 

the TOTAL DISTANCE by 10, and multiply 

the decimal portion by 12 to find your stride 

length in feet and inches. Example: If you 

walk 23 feet in 10 steps, your stride length 

is 2.3 feet. Multiply 0.3 x 12 = 4. Your stride 

length is 2 feet, 4 inches.

 (2740, 2790 

 Repeatedly press the red MODE 

button until “mi” appears. Press the blue SET 

button once to enter setting mode. Display 

will shift to show stride, in feet and inches. 

Press and hold down the blue SET button to 

increase stride length. Press the red MODE 

button to exit setting mode. 

 Pressing the white RESET button 

resets stride length to 2' 0". 

 Repeat-

edly press the red MODE button until “kcal” 

appears. Press the blue SET button once 

to enter setting mode, then press and hold 

the blue SET button to increase weight (in 

pounds). Press the red MODE button to exit 

setting mode. 

 Pressing the white RESET button 

resets weight to 120 lbs.

 Repeatedly 

press the red MODE button until “AM” or 

“PM” appears. Press the white RESET 

button. The dash will stop flashing. Press 

and hold down the red MODE button until 

the correct hour is displayed; release button. 

Press and hold down the blue SET button 

until the correct minutes are displayed; 

release button. Press the white RESET button 

to exit setting mode. The dash will begin 

flashing. The clock is now set.

While gently holding the belt clip open, slide 

the pedometer onto your belt or the top edge 

of your pants or skirt. It should fit snugly and 

level, above one knee. 

 The pedometer should be as vertical as 

possible. Walkers with larger stomachs may 

find it helpful to wear the pedometer farther 

back on the body, toward one hip. The cover 

 

To avoid losing or dropping your pedometer, 

use the included leash and clip to fasten the 

pedometer securely to your clothing. 

Attach the pedometer  

to the leash by looping the leash through the  

pedometer leash slot. Next, loop the leash 

through the metal clip. Finally, clasp the waist-

band of your clothing with the metal clip. You 

can also use a safety pin to fasten the leash to 

your clothing, loop the leash through your belt 

or belt loop, or use a badge holder. 

ACCUSPLIT, Inc.  •  2290M Ringwood Ave.  •  San Jose, CA 95131

800-965-2008  •  925-226-0888  •  FAX 925-463-0147  •   www.ACCUSPLIT.com   •  support@ACCUSPLIT.com

Once you put on your pedometer with the 

cover closed, it will automatically begin 

to record your steps, distance (2740, 

 calories burned (2790 only), 

and activity time. Repeatedly press the 

red MODE button to cycle through the 

pedometer modes: 

STEP → DISTANCE → CALORIE → CLOCK 

→

 ACTIVITY TIMER → STEP

Most people prefer to reset step, distance, 

and calorie counts daily. To reset: From 

STEP, DISTANCE, or CALORIE mode, press 

and hold the white RESET button for at least 

2 seconds.

When the display starts to dim or goes 

blank, it is time to replace the battery. Your 

pedometer uses one Type L1142 (LR43) 1.5 

volt silver oxide battery. To replace:

1.  Insert a coin into the slot on the front of 

the case, and twist counterclockwise to 

loosen the battery door.

2.  Remove battery door and take out the 

old battery. Replace it with a new battery. 

The battery’s positive (+) terminal should 

be FACE UP while you put it into the 

pedometer.

3.  Put the battery door back on and twist the 

coin clockwise to tighten.

Congratulations on taking the first step to wellness 

with your purchase of an ACCUSPLIT pedometer. 

It’s easy to set up your new pedometer. 

Just follow the steps below, and start walking!

Red: 

MODE

Blue: 

SET 

White: 

RESET 

970-048

(Badge holder  

not included)