EXFO Photonic Solutions Div. IQS-12001B ユーザーズマニュアル

IQS-12001B

Cable Assembly and Component Test System

SPECIFICATIONS

a

Ports Gigabit Ethernet

Two 10/100Base-T

Two 10/100Base-T 

Two 10/100Base-T and two

and one Gigabit Ethernet

Connector types

RJ-45 (ISO 8877)

RJ-45 (ISO 8877) and LC

RJ-45 (ISO 8877) and LC

Connect speed (Mb/s)

10/100

10/100/1000 

10/100/1000 

Duplex mode

Full/half-duplex 

Full/half-duplex 

Full/half-duplex 

auto-negotiation auto-negotiation

auto-negotiation

Maximum port capacity (Mb/s)

200 (bidirectional)

2000 (bidirectional)

2000 (bidirectional)

Ethernet testing

RFC 2544

RFC 2544

RFC 2544

RFC 1242

RFC 1242

RFC 1242

SPECIFICATIONS

a

b

b

c

Testing time 

d

(s)

< 6 

< 6

< 6 

Cable assembly length (m)

1.8 to 1500 

1.8 to 1500

1.8 to 500 

Insertion loss measurement uncertainty 

± 0.03 

e

± 0.03 

e

± 0.07 

f

Insertion loss measurement stability 

g

(dB) 

< 0.005

< 0.005

< 0.028

Reflectance range (dB)

−30 to −75

−30 to −75

−10 to −50

Reflectance measurement uncertainty (dB)

±1 (−30 to −70) 

±1 (−30 to −70)

± 1.2 (−10 to –30)
± 1.5 (−30 to –40)

±2.2/±1.7 (−70 to −75)

±1.7 (−70 to −75)

± 1.6 (−40 to –43)
± 2.9 (−43 to –50)

Reflectance measurement repeatability 

h

(dB)

±0.1 (−30 to −65)

±0.1 (−30 to −65)

± 0.2 (−10 to –30)

±0.2 (−65 to −70)

±0.2 (−65 to −70)

± 0.4 (−30 to –40)

±0.4 (−70 to −75)

±0.5 (−70 to −75)

± 0.6 (−40 to –43)
± 1.8 (−43 to –50)

Wavelengths (nm)

1310/1550

1490/1625

850/1300

Output channels

Up to 32 channels

Up to 32 channels

Up to 32 channels

Test method

End-to-end/bidirectional

End-to-end/bidirectional

End-to-end/bidirectional

a.  Calculated and measured with the following considerations:

• Based on recommended procedure for ORL measurements
• The FOA-300 series’ uncertainty is included in all uncertainty values
• Although tests are possible with other fiber-optic adapters, these specifications are only valid with the FOA-300 series
• Cable assemblies < 1.8 m can be tested using a non-reflective termination
• With 15 minute warm-up time

b.  For SMF-28 fiber. At 23 ºC ± 1 ºC in High-Sensitivity Reflectance mode with no switch.
c.  At 850 nm and 1300 nm. For 62.5/125 µm fibers. At 23 °C ± 1 °C, after 30 minutes warmup. Switch module connectorized with FC/PC connectors. 

Uncertainty due to launching conditions not included.

d.  Calculation and storage time for simplex, dual-wavelength IL/reflectance end-to-end measurements (Standard Reflectance Sensitivity mode, 500 meter range); 

does not include referencing and connection time.

e.  For simplex measurements using FOA-322 adapter. Uncertainty for MTP to MTP, MT-RJ to MT-RJ, MTP to fanout and MT-RJ to fanout is ± 0.06 dB 

(reported with a level of confidence of 95 %). This does not include uncertainties due to connector, connector adapter or switch PDL. 

f.  For simplex measurement using FOA-322 adapter. Uncertainty for MTP to MTP, MT-RJ to MT-RJ, MTP to fanout and MT-RJ to fanout is ± 0.08 dB 

(calculated for a level of confidence of 95 %). Does not include uncertainties due to connector, connector adapter or uncertainties due to mode dependence of the switch.

g.  For a stable connection, over 15 minutes, at constant temperature.
h.  For a stable connection, over 10 measurements.

GENERAL SPECIFICATIONS

Communication interfaces

General-purpose interface bus (GPIB) 
Ethernet (10/100 Base-T)
RS-232

Temperature

Operating

0 °C to 40 °C

(32 °F to 104 °F)

Storage

−40 °C to 60 °C

(−40 °F to 140 °F)

Relative humidity

80 % maximum, non-condensing

21 CFR 1040.10

CLASS 1 LASER PRODUCT

IEC 60825-1:2001

CLASS 1 LASER PRODUCT

Expansion units as required, user guide, certificate of compliance, custom report, label generator, IQS-12001B software and EUI-89 FC narrow key connector.