Behringer Virtualizer 3D FX2000 ユーザーズマニュアル
19
VIRTUALIZER 3D FX2000 User Manual
4.5 Using the VIRTUALIZER 3D in a MIDI setup
Thanks to the integrated MIDI interface, you can incorporate the FX2000 in a
MIDI setup. The VIRTUALIZER 3D can receive and send both program changes
and controller changes. Thus, you can use program changes using MIDI with a
sequencer or with any other MIDI device. Connect the FX2000 e.g. as follows:
MIDI In
MIDI Thru
MIDI Out
MIDI Out
MIDI In 2
MIDI In 1
MIDI Out
MIDI In
MIDI
Sequence
Fig. 4.4: VIRTUALIZER 3D in MIDI connection with a sequencer (computer) and a keyboard
5. MIDI Functions of the FX2000
Due to the complete implementation of the MIDI interface, it is very easy to
integrate the VIRTUALIZER 3D in a MIDI System.
•
MIDI IN
All MIDI data that are sent to the FX2000 (sequencer, MIDI foot controller, etc.)
are received at the MIDI IN port. If you want to use the FX2000 as an effects unit
in a guitar rack, you can connect a MIDI foot controller to the MIDI IN socket,
and use it to change the program presets. If you are simultaneously operating
another MIDI device, you can transfer the control commands of the MIDI foot
controller using the MIDI THRU socket of the VIRTUALIZER 3D.
•
MIDI THRU
The MIDI THRU socket allows you to loop through incoming MIDI signals.
All control commands that arrive at the MIDI IN socket can be passed on to other
MIDI devices and instruments using the MIDI THRU socket.
•
MIDI OUT
Use the MIDI OUT to send data to a connected computer or other VIRTUALIZER 3D.
5.1 Saving data via MIDI
To store all presets outside the VIRTUALIZER 3D, you can use a special form
of MIDI communication called system exclusive data (SysEx). With SysEx,
the VIRTUALIZER 3D sends information about its manufacturer, unit type, and all
parameter settings for all presets to a sequencer or MIDI file recorder. To activate
this very practical function, press the SETUP key in SETUP mode. Turn the 1st EDIT
CONTROL to select “DUMP”. Your VIRTUALIZER 3D is now ready to transfer your
system exclusive data. Select a track on your MIDI sequencer, get ready for
recording, start the recording and turn the JOG WHEEL. The data transfer is
indicated by a “GO” in the display.
To load the data back into the FX2000, select “DR.EN” in SETUP mode (see chapter
To load the data back into the FX2000, select “DR.EN” in SETUP mode (see chapter
3.6.1). Turn the JOG WHEEL until “DR.EN” blinks. Now, start your MIDI sequencer
and the preset data is automatically transferred to the FX2000. In this mode,
information sent from the MIDI sequencer is automatically stored while receiving,
without asking for confirmation.
6. Installation
6.1 Mains connection
Before connecting the VIRTUALIZER 3D to the mains, please carefully
check that your equipment is set to the correct voltage! The fuse holder
on the mains socket has 3 triangular markings. Two of these triangles are located
opposite each other. The VIRTUALIZER 3D is set at the operating voltage indicated
beside the markings and can be changed by turning the fuse holder by 180°.
CAUTION: This is not applicable for export models, which were designed
only for a mains voltage of 120 V!
Connection to the mains is made by means of a mains cable with an IEC
Connection to the mains is made by means of a mains cable with an IEC
receptacle which complies with the required safety regulations.
◊
Please note that all pieces of equipment must be grounded. For your
own safety, under no circumstances should you remove or deactivate
the grounding of the equipment or the mains cable.
own safety, under no circumstances should you remove or deactivate
the grounding of the equipment or the mains cable.
6.2 Audio connections
As standard, the BEHRINGER VIRTUALIZER 3D features electronically servo-
balanced inputs and outputs. If possible, connect the unit to other devices in a
balanced configuration to allow for maximum interference immunity.
◊
Installation and operation of this equipment must be carried out by
competent staff only. Both before and after installation, the staff using
the equipment should make sure that it is properly grounded since
otherwise electrostatic discharge etc. can lead to an impairment of
its operation.
competent staff only. Both before and after installation, the staff using
the equipment should make sure that it is properly grounded since
otherwise electrostatic discharge etc. can lead to an impairment of
its operation.
strain relief clamp
sleeve
tip
sleeve
(ground/shield)
Unbalanced ¼" TS connector
tip
(signal)
strain relief clamp
sleeve
ring
tip
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced ¼" TRS connector
ring
cold (-ve)
tip
tip
hot (+ve)