West Elm Abacus Floor Lamp 組み立て手順
Important Safety Instructions:
• For safety purposes, this lamp is equipped with a polarized plug (one blade is wider than the other). If the plug does not fi t
securely into your outlet, do not force it, contact a professional electrician. Use the plug with an extension cord only if it can be
fully inserted into the cord’s socket. Never alter the plug in any way.
• This instruction is provided for your safety. It is important that they are read carefully and completely before assembling the
fi xture.
• This fi xture has been rated for up to 100 Watt TYPE A standard incandescent light bulb (not included) or 23-watt compact
fl uorescent bulb (included). To avoid the risk of fi re, do not exceed the recommended wattage.
• Save this instruction.
WARNING:
• To reduce the risk of fi re, electrical shock or personal injury, always turn off light fi xture and unplug, allowing it to cool prior to
replacing light bulb.
• Do not touch bulb when fi xture is turned on.
• Do not look directly at lit bulb. Keep fl ammable materials away from lit bulb.
Pre-assembly:
•Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any contents until after
• For safety purposes, this lamp is equipped with a polarized plug (one blade is wider than the other). If the plug does not fi t
securely into your outlet, do not force it, contact a professional electrician. Use the plug with an extension cord only if it can be
fully inserted into the cord’s socket. Never alter the plug in any way.
• This instruction is provided for your safety. It is important that they are read carefully and completely before assembling the
fi xture.
• This fi xture has been rated for up to 100 Watt TYPE A standard incandescent light bulb (not included) or 23-watt compact
fl uorescent bulb (included). To avoid the risk of fi re, do not exceed the recommended wattage.
• Save this instruction.
WARNING:
• To reduce the risk of fi re, electrical shock or personal injury, always turn off light fi xture and unplug, allowing it to cool prior to
replacing light bulb.
• Do not touch bulb when fi xture is turned on.
• Do not look directly at lit bulb. Keep fl ammable materials away from lit bulb.
Pre-assembly:
•Remove all parts and hardware from box along with any plastic protective packaging. Do not discard any contents until after
assembly is complete to avoid accidentally discarding small parts or hardware.
Parts enclosed:
(1)Finial (A)
(1)Harp Top (B)
(1)Harp (C)
(2)Harp Caps (D)
(1)Socket (E)
(1)Saddle (F)
(1)Shade (not included) (G)
Parts enclosed:
(1)Finial (A)
(1)Harp Top (B)
(1)Harp (C)
(2)Harp Caps (D)
(1)Socket (E)
(1)Saddle (F)
(1)Shade (not included) (G)
(1)Crimp Connector A (H)
(1)Allen Wrench (I)
(2)set screws (J)
(1)Metal Ring (K)
(8)Glass Balls (L)
(1)Crimp Connector B (M)
(3)Metal Tubes (N)
(1)Lamp Base (O)
(2)set screws (J)
(1)Metal Ring (K)
(8)Glass Balls (L)
(1)Crimp Connector B (M)
(3)Metal Tubes (N)
(1)Lamp Base (O)
To Assemble:
1. Screw on one metal tube (N) onto the top of lamp base (O) by turning it in a clockwise direction untill tight. Do not overtighten.
2. Screw the second metal tube (N) onto the top of assembled metal tube (N) (from step 1) turning in it in a clockwise direction
untill tight. Screw on the last metal tube (N).
3. Place the 8 pieces of glass balls (L) over the metal tubes (N), ensure all glass balls (L) to go through the metal tubes (N) and the
bottom of glass balls (L) with plastic washer is facing downward towards the fl oor.
4. Place metal ring (K) onto the top of glass ball (L) and screw in the set screws (J) with the allen wrench (I) untill tight.
5. Connect the crimp connector A (H) and crimp connector B (M), making sure the plug is completely connected. Insert the
assembly plug into the metal tube (N).
6. Turn the saddle (F) in a clockwise direction until tight. Do not overtighten.
7. Slightly squeeze the harp (C) and Insert it into the saddle (F), lower the two harp caps (D) until they cover the two-pronged
saddle (F).
4. Unscrew the fi nial (A) from the harp top (B). Place shade (G) (not included) over the assembled harp, making sure the harp top
(B) extends through the hole at the top of the shade (G) (not included).
5. Attached the fi nial (A) and tighten to secure the shade (G) (not included).
6. Insert a bulb-Max 100 watt maximum TYPE A standard incandescent light bulb (not included) or 23-watt compact fl uorescent
bulb into the socket (E). DO NOT EXCEED SPECIFIED WATTAGE.
1. Screw on one metal tube (N) onto the top of lamp base (O) by turning it in a clockwise direction untill tight. Do not overtighten.
2. Screw the second metal tube (N) onto the top of assembled metal tube (N) (from step 1) turning in it in a clockwise direction
untill tight. Screw on the last metal tube (N).
3. Place the 8 pieces of glass balls (L) over the metal tubes (N), ensure all glass balls (L) to go through the metal tubes (N) and the
bottom of glass balls (L) with plastic washer is facing downward towards the fl oor.
4. Place metal ring (K) onto the top of glass ball (L) and screw in the set screws (J) with the allen wrench (I) untill tight.
5. Connect the crimp connector A (H) and crimp connector B (M), making sure the plug is completely connected. Insert the
assembly plug into the metal tube (N).
6. Turn the saddle (F) in a clockwise direction until tight. Do not overtighten.
7. Slightly squeeze the harp (C) and Insert it into the saddle (F), lower the two harp caps (D) until they cover the two-pronged
saddle (F).
4. Unscrew the fi nial (A) from the harp top (B). Place shade (G) (not included) over the assembled harp, making sure the harp top
(B) extends through the hole at the top of the shade (G) (not included).
5. Attached the fi nial (A) and tighten to secure the shade (G) (not included).
6. Insert a bulb-Max 100 watt maximum TYPE A standard incandescent light bulb (not included) or 23-watt compact fl uorescent
bulb into the socket (E). DO NOT EXCEED SPECIFIED WATTAGE.
7. Plug fi xture into the proper electrical outlet and test fi xture.
Care instructions:
• Wipe clean with a soft, dry cloth or static duster.
• Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the fi xture’s
fi nish.
• Wipe clean with a soft, dry cloth or static duster.
• Always avoid the use of harsh chemicals or abrasive cleaners as they may cause damage to the fi xture’s
fi nish.