BlueAnt T8 Micro Bluetooth Headset プリント

3. The Red LED indicators will light up showing that the T8 is 

    being charged.

4. When charging is complete the Red LED indicators will turn off. 

5. Remove the charger plug from the T8 then switch off the charger.

Note: The rechargeable battery in the T8 will take several complete 

charges till it reaches its optimum storage capacity. 

After charging the fi rst time, use the T8 as normal until a ‘low battery’ is 

indicated. Charge again and repeat…!!!

 

Bluetooth Version…............. v2.0

Supported Bluetooth 
Profi les ................................ Headset and Handsfree

Number of devices .............. Stores information for 8 different devices

Frequency Band .................. 2.4GHz ~ 2.4835 (frequency Hopping

Certifi cation Approvals ........ CE, FCC, BQB, C-Tick

Security ............................... 128 bit Digital Encryption

Talk Time ............................. 9 Hours

Standby Time ...................... 250 Hours

Battery................................. Rechargeable 120mAh Li-Polymer

Charger ............................... 110v – 240v Switch Mode Charger

Operating range .................. Up to 10 meters

Weight ................................. 13  grams

Dimensions ......................... 52 x 26 x 28 mm

Indicator Lights .................... Blue, Red and Purple 
 

(LED’s can be turned off)

Compatibility ....................... Windows, Mac, Mobile Phones, 
 

Pda’s and VOIP applications

Before you can use your headset, you must ‘link’ it with the device you wish to use.

1. First turn the T8 ON, then Press and Hold the MFB

 button for about 3 

  seconds. At this point the T8 is in Standby mode i.e. not connected to any device.

2. To put your headset go into Pairing mode, Press and Hold the Volume UP

  button for about 2 seconds. The blinking blue and red indicators will alternate.

1. Turn on the Bluetooth function of your phone or device.

2. Perform a “Bluetooth device discovery” from your phone or device.

3. Select ‘T8 micro”  from the list of discovered devices 

4. Enter the Pincode/Passkey “0000”.

5. Select the T8 micro from the list of paired devices and press Connect.

  Note: Some devices will not require this last step

Your headset and your phone should now be paired and connected, ready to 

make and receive calls. Depending on your device, you may see that a headset 

symbol has appeared on you screen. To confi rm they are successfully paired 

and operating properly please try the following.

1. On your phones keypad, dial a contact you wish to call.

2. Press Send on your phone to initiate the call. 

  The call will be heard on the headset.

1. Power ON your headset: Press and Hold the MFB

 for about 3 seconds until 

the blue indicator fl ashes twice. After powering on, your headset will automatically 

connect to your last used phone if it is in operating range. If no paired phone is in 

range or no phone has been paired, the T8 will enter Standby mode.

2. Power OFF your headset: Press and Hold the MFB

 for about 3 seconds 

until the red indicator fl ashes twice.

3. To enter Pairing mode: While in Standby mode, Press and Hold the Volume 

Up

 button for about 2 seconds

4. To Answer or End a call: Press the MFB

 once when there is an incoming 

call to Answer. Press the MFB

 once again to end the call.

5.  To Reject* a call: Press and Hold the MFB

 for about 2 seconds when 

there    is an incoming call.

6.  To Redial* the last call: Press and Hold the Volume Down Button

 for 

about 2 seconds.

7. To activate Voice Dialing*: while connected to your phone, Press the MFB

once. Voice commands must have been previously recorded into your phone 

(see your phones user guide)

8. To adjust the Volume: Click the Volume Up 

 or Volume Down Button 

during a call. Adjust to the desired level. The volume level you set to will be 

remembered by the T8 and used on the next call.

9. To Disable/Enable the LED indicators: Double Press the Volume Up 

 / 

Down Button 

when your headset is in standby mode.

10. To Reset your headset to factory settings: Press and keep Holding one 

after the other the Volume Up Button 

, MFB then Volume Down Buttons 

. 

When you click the third button the T8 micro will blink purple twice and then 

switch itself off. You must be in Standby mode to reset the T8 micro i.e. while 

not connected to any device.

*   To use these functions, your phone/device must support the Bluetooth Handsfree 

Profi le. Headset profi le will not activate these features of the T8 micro.

1. 

MFB (Multi Function Button)

2. 

Volume Up Button

3. 

Volume Down Button

See the support section of www.blueantwireless.com for troubleshooting and 

Frequently Asked Questions (FAQ) as well as info on using with computers for 

VOIP application\s.

Please make sure you have the latest fi rmware upgrade for your Phone especially

if you are using a PDA Phone. Go to the support section of the manufacturers’ 

website to check you have the latest version. Many new mobile phones, pda’s and

computers phones require a Bluetooth patch to improve Bluetooth functionality 

from the original released version.

Phones can become prone to software and memory issues which may cause 

Bluetooth reconnection problems. This can be fi xed simply by turning the phone off 

and back on again. The phone will be reset and the working memory cleared. 

This manual is published by BlueAnt. The information contained in this document is 

subject to change without notice. All rights reserved.

The Bluetooth word, mark and logos are owned by the Bluetooth SIG, Inc. and any 

use of such marks by BlueAnt is under license. Other trademarks and trade names 

are those of their respective owners.

 

You are cautioned that changes or modifi cations not expressly approved by the 

part responsible for compliance could void the users authority to operate the equipment.

 

This equipment has been tested and found to comply with the limits 

for a Class B digital device, pursuant to part 15 of the FCC rules. These limits 

are designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to 

try to correct the interference by one or more of the following measures:

> Reorient or relocate the receiving antenna.

> Increase the separation between the equipment and receiver.

> Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help. You are cautioned 

that changes or modifi cations not expressly approved by the party responsible for 

compliance could void your authority to operate the equipment.

This Transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

 Prolonged use of a headset at high volumes may affect your hearing 

capacity. Using for extensive time periods may result in noise induced hearing loss 

(NIHL). Be careful about using in noisy environments as the tendency is to turn 

the headset up to compensate. Hearing loss may occur if the headset is used at 

maximum volumes for more than 5 minutes per day. Hearing loss may occur if the 

headset is used at medium volumes if used for more than 1 hour per day. Exposure 

to sound at such a close range for more than eight hours a day may result in hearing 

loss, even at low levels.

Power on 

Blue indicator blinks twice

Power off  

Red indicator blinks twice

Standby mode  

Blue indicator blinks once every 4 seconds

Sniff mode  

Blue indicator rapidly blinks twice every 4 seconds

Pairing mode  

Red & Blue indicators alternately blink 

Incoming call  

Purple indicator blinks once per second

Active call 

Blue indicator rapidly blinks 3 times every 4 seconds

Low battery  

All Blue indicators will change to Red

Charging  

Red indicator is continuously  ON steady on

Charging complete  

Red indicator turns OFF

Reset  

Purple indicator blinks twice

    Note: Sniff mode means your headset has a connection with your phone 
    but is conserving power, and will wake up when any function is activated.

Getting started… charging of your T8 will take about 2 hours.

Follow the procedure as follows:

1. Insert the  T8 Wall Charger into a DC power source and switch ON.

2. Insert the plug on the end of the T8 charging cable into your headset 

   as shown below. 

1.

MFB (Multi Function Button)

2.

3.

The Red LED indicator

The Red LED indicator

Note: Before use please 

read the Additional 

Information sections 

in this users guide.

1. Make sure the last device used has Bluetooth switched off or is out of range.

2. Follow the procedure in ‘Pairing your Bluetooth device’ above

1. Make sure the last used device has Bluetooth switched off or is out of range.

2. Go to your phones Bluetooth Menu, Select the T8 micro and Press Connect

1.  Should you be having diffi culties in the operation of your T8 micro please refer 

 

to the online FAQ and support documents..

2.  Check our website for more information, updated manuals and troubleshooting.      

 

 www.blueantwireless.com 

 

3.  Call us and speak to one of the BlueAnt Wireless Customer Service Team 

     We will clarify whether you have a hardware or connection issue.

4.  Return the unit directly to BlueAnt for testing and replacement of faulty items

    – Please call to arrange a Return Merchandise Authorization (RMA) number.

1.   BlueAnt Warrant the original purchaser of this product only.

2.  BlueAnt will replace or repair any faulty product provided it has not been 

 

misused or abused in any way.

3. There are no user serviceable parts inside this product. Using a non-

 

authorized repairer will void the warranty.

4.  The T8 micro Warranty is valid for 2 years (24 months) from the date 

 of 

purchase.

•  Proof of purchase must be supplied to obtain warranty.

•  Headset must be in original packaging with serial number for warranty to be valid.

5.  Warranties are effective from the proof of purchase date and not from the date 

 

of any subsequent repair or replacement.