Superchips Inc. Car Stereo System 1715 maz ユーザーズマニュアル

 
 

Page 5 of 16

  

Form 0129L 03/29/07                                                                                            

 Superchips Inc

Superchips Inc.  

1790 East Airport Blvd., Sanford, FL. 32773  (407) 585-7000  http://www.Superchips.com 

Superchip & Superchips are registered trademarks of Superchips, Inc. 

 

 

 

 

Insure the ignition switch is OFF, then press the ‘>’ key on the keypad.  

 

The MAX MicroTuner alternately displays the following messages: 

 

then 

 

 
 

Turn the ignition switch to the ON position. Press the ‘>’ key on the keypad. The MAX 
MicroTuner will beep and display the message: 

 

 

Press the ‘A’ key on the keypad to continue with the tuning process.  

 

Press the ‘B’ key to read and/or clear any Diagnostic Trouble Codes from the vehicle. 
See provided  Reader Instructions and Code Interpretations in the separate manual 
for this purpose with your MAX Micro tuner. 

 

The MAX MicroTuner will beep and display the message: 

 

  

If ‘NO’ is pressed, the MAX MicroTuner will beep and display the following messages: 

 

then 

 

 then 

 

 

After pressing a key, the MAX MicroTuner beeps and returns to

  

at Step 2. 

If ‘YES’ is pressed, the MAX MicroTuner will proceed to establish communications and 
display the following message: 

 

 

The MAX MicroTuner is establishing communications with and identifying the vehicle 
computer. If the MAX MicroTuner has not yet been used to program a vehicle, no vehicle 
ID will be stored in the MAX MicroTuner. In such a case, the MAX MicroTuner will begin 
saving the STOCK program for the vehicle. If the vehicle ID matches a vehicle ID stored in 
the MicroTuner, the MAX MicroTuner will go directly to the Return to Stock Sequence 
Section at Step 10 that follows. 

 

then 

 

 then 

 

* 

Other error codes, with or without explanations may be displayed. 

 

Pressing the ‘>’ key will cause the MAX MicroTuner to beep and display the message: 

 

 

After a few seconds the MAX MicroTuner resets and returns to the power-up self test. 

 

 
 

Page 6 of 16

  

Form 0129L 03/29/07                                                                                            

 Superchips Inc

Superchips Inc.  

1790 East Airport Blvd., Sanford, FL. 32773  (407) 585-7000  http://www.Superchips.com 

Superchip & Superchips are registered trademarks of Superchips, Inc. 

 

 

 

The manufacturer’s STOCK program is first saved in the MAX MicroTuner to allow the 
vehicle to be reprogrammed to STOCK condition if necessary. The STOCK program is 
saved only the first time the vehicle is programmed. 

 

Once the MAX MicroTuner has established communications, it will beep and display the 
message: 

 

Turn the ignition to the OFF position and press the ‘>’ key on the keypad.  The MAX 
MicroTuner will beep and blink the following message for approximately 6 seconds: 

 

 

After initialization is complete, the MAX MicroTuner will beep and display the message: 

 

 

Turn the ignition to the ON position. The MAX MicroTuner will beep and start saving the 
stock program. This will take about three minutes. The MAX MicroTuner will blink the 
following message: 

 

The bottom line of the display shows the progress of the stock upload.   

 

When completed, the MAX MicroTuner checks to see if the stock program it has uploaded 
can be found in its internal database. If not it will display the message: 

 

then 

then 

 

If the stock upload is found in the internal database, the MAX MicroTuner will beep and 
display the message: 

 

 

The MAX MicroTuner is testing to see if the Passive Anti-Theft System (PATS) is active. If 
PATS is active, the MAX MicroTuner will beep and display the message: 

 

 

If PATS is not active, the MAX MicroTuner automatically clears the vehicle DTCs then 
displays the message: 

 

 

 

 

The MAX MicroTuner will then beep and display the message: 

 

The MAX MicroTuner allows for three levels of performance tuning.