Spectra Logic T50E プリント

Spectra T50e

Quick Start Guide

P.N. 90970017, Rev. C

www.spectralogic.com

Page 2 of 2

 

If you have only one partition enabled, use Bulk Load for the initial setup. Refer to the Spectra T50e Library User Guide if you have 

more than one partition.

1. Using the stylus, select Menu > General > Import/Export > Bulk Load. Both left-side magazines release.

2. Remove the bottom left magazine and set it on a stable surface.

CAUTION! Be careful while handling fully-loaded magazines as they are heavy!

3. Load the cartridges sequentially starting at slot 1 and continue with the top left-side magazine, if needed. Reinsert the left-side magazine(s) and continue 

with the right-side magazines, if needed. See the Spectra T50e Library User Guide for information about the expansion slots (slots 48 through 50).

4.Gently push each magazine into the library until it is fully seated and press Stop Importing. The library inventories the cartridges. 

The USB drive that came in your Document Kit (see Unpack and Verify the 
Components on page 1) contains the library’s firmware as well as the option 
keys that you purchased. Follow these steps to load the firmware and keys.

1. Insert the USB drive in the USB port at the back of the library.

2. Plug the power cord in if it is not already connected.

3. Press the front panel power button for two to three seconds.

4.Wait while the library performs its power-on sequence, which typically 

takes six to nine minutes.

During the AutoInstall process, the library upgrades the firmware from 
the USB drive, reboots itself, and automatically installs the option keys 
during the remainder of the power-on sequence.

 Do not remove the USB drive until after the Login screen 

appears, but do not leave the USB drive in the library after the 
installation.

 

After the power-on sequence completes, the login screen displays.

1. Using the stylus, touch (to select) the User box and type su.

2. Leave the password field blank, and select Login.

3. Wait for the initialization process to complete.

4.Close the keyboard by selecting its icon with the stylus.

Note: If you are prompted to calibrate the touch screen, follow the 

instructions on the screen. You must use the stylus for the 
calibration procedure to complete successfully.

Follow these steps to allow the library to automatically 

create a partition.

1. Using the stylus, select Menu > Configuration > Partitions > 

Automatically create a partition > New.

2. Use the wizard to create the partition, and then choose one option:

ƒ Save Library Configuration to USB (recommended)
ƒ Save Library Configuration to autosupport@spectralogic.com 

(recommended)

ƒ Don’t Save Library Configuration (not recommended)

3. Select Next and Save.
To manually create partitions, see the Spectra T50e Library User Guide 
for instructions.

Follow these steps:

1. Ensure that your SCSI HBA BIOS has LUN support enabled.

2. Reboot your host system, if needed.

3. Install your backup application, if it is not already installed.

4.Configure the application to work with the Spectra T50e library.

Go to 

 to download device drivers 

for the library.

If you need assistance, contact us using one of these options.

Email:
Web:
Phone:

support@spectralogic.com

www.spectralogic.com/support

1.800.227.4637

1.303.449.0160

support@spectralogic.com

www.spectralogic.com/support

44 (0) 870.112.2185

Create a test backup job.

Refer to the documentation that came with your backup application 
for instructions.

Note: Reference the Spectra T50e Library User Guide for comprehensive 
instructions on how to operate your new library. Access the manual either 
on the Product CD or at 

.

Stylus—used to navigate in screens.

1 Insert USB drive

2 Connect power cord

USB 

drive

3 Press power button

Stylus in holder

1 Type “su”

3

4

Login

Close keyboard 

Wait

su

2

Slot 1 

Access port

 Replace magazines 

in the same locations. 

Right

Left

(bar code labels must face out) 

 Load cartridges sequentially starting at slot 1. 

Top

Top

Bottom

2

3

4

7

11

8

23

20

12

24

5

6

15

9

10

16

19

27

32

36

44

28

47

35

31

39

40

43

1

Access port

50

49
48

Bottom

Expansion slots