Roland BR-600 ユーザーズマニュアル
216
Error Messages
Re
v0.10
v0.10
Drive Busy!
Cause :
If this message appears after you have
been using the memory card with the
BR-600, the data on the card has
become fragmented, causing delays in
reading and writing data.
been using the memory card with the
BR-600, the data on the card has
become fragmented, causing delays in
reading and writing data.
Or, you could be using memory card
with a slow processing speed.
with a slow processing speed.
* In cases of unfavorable disc access conditions, such as
when track editing, punch-in/out recording, etc. is
used to connect phrases (musical data) of several
seconds.
used to connect phrases (musical data) of several
seconds.
Solution 1 : Reduce the number of tracks that are
played back simultaneously. Use track
bouncing etc. to combine tracks, or erase
data from tracks which you do not need
to playback, and then try the playback
again.
bouncing etc. to combine tracks, or erase
data from tracks which you do not need
to playback, and then try the playback
again.
Solution 2 : Reduce the number of tracks that are
being recorded simultaneously.
Solution 3 : Reduce the Data Type (STD (LV1) or
LONG (LV2)), and then try creating the
song again.
song again.
Event Full!
Cause :
The BR-600 has used up all the events
that can be handled by one song.
that can be handled by one song.
Solution :
Perform the Song Optimize operation
(p. 87).
(p. 87).
Turn Off Pitch Correction!
Cause :
You cannot use the loop effects or
phrase trainer while Pitch Correction is
on.
phrase trainer while Pitch Correction is
on.
Solution :
Press [PITCH CORRECTION] to turn it
off, and try the operation once again.
off, and try the operation once again.
Memory Full!
Cause :
The total time of the drum sounds
loaded with tone load has exceeded 13
seconds.
loaded with tone load has exceeded 13
seconds.
Solution :
Make sure the drum sounds being
loaded by means of tone load do not
exceed a total of 13 seconds (p. 138, p.
174, p. 186).
loaded by means of tone load do not
exceed a total of 13 seconds (p. 138, p.
174, p. 186).
Cause :
No rhythm pattern memory remaining.
Solution 1 : Delete any unneeded rhythm patterns
Solution 2 : Delete any unneeded drum sounds in
Cause :
You have attempted to import an SMF
that exceeds the available memory for
imported files.
that exceeds the available memory for
imported files.
Solution :
Delete any unneeded rhythm patterns
(p. 153).
(p. 153).
No Card!
Cause :
You have tried to operate the recorder,
or access the memory while the
memory card (CompactFlash) is not
inserted, or is not inserted properly.
or access the memory while the
memory card (CompactFlash) is not
inserted, or is not inserted properly.
Cause :
The memory card has been removed
after selection of data on that memory
card.
after selection of data on that memory
card.
Solution :
Turn off the BR-600, properly insert the
memory card, then turn the BR-600 back
on.
memory card, then turn the BR-600 back
on.
No File!
Cause :
The file you are trying to import with
WAV/AIFF/SMF import or Tone Load
was not found.
WAV/AIFF/SMF import or Tone Load
was not found.
Solution :
Have the file you want to import ready.
What is an event?
The smallest unit of memory used by the BR-600 to
store recorded results on a memory card is the event. A
newly created song provides approximately 2,000
events per song.
For each track, one recording pass uses two events.
Operations such as punch-in/out or track copy also
use up events.
The number of events that are used up will fluctuate in
a complex way.
store recorded results on a memory card is the event. A
newly created song provides approximately 2,000
events per song.
For each track, one recording pass uses two events.
Operations such as punch-in/out or track copy also
use up events.
The number of events that are used up will fluctuate in
a complex way.
Even if there is capacity remaining on the memory
card, further recording or track editing will not be
possible if all of the events are used up. In such cases,
an error message such as “Event Full” will appear.
card, further recording or track editing will not be
possible if all of the events are used up. In such cases,
an error message such as “Event Full” will appear.
BR600_e2 216 ページ ２００６年４月１７日 月曜日 午前９時３分