VistaQuest N7227V5 ユーザーズマニュアル
– 58 –
✱
ZN 0 1 B A CK
DO O R
A
↑
Flashing Cursor if “6” is
pressed (system ready for
next word).
pressed (system ready for
next word).
9. Press “6” to accept the selected
word.
Note: If these are the only words
you are using for the descriptor,
press “ 8” instead of “ 6” to save them
in memory.
Note: If these are the only words
you are using for the descriptor,
press “ 8” instead of “ 6” to save them
in memory.
10. The two words in our example have
now been entered. Note, however,
that up to three words may be
entered (provided the number of
characters will fit on the screen).
Press “8” to save all words in
memory.
that up to three words may be
entered (provided the number of
characters will fit on the screen).
Press “8” to save all words in
memory.
✱
ZN 0 1 B A CK
DO O R
The “A” with the flashing cursor over
it will disappear, indicating that the
word(s) are stored in memory for that
zone, as shown in the display at the
left.
it will disappear, indicating that the
word(s) are stored in memory for that
zone, as shown in the display at the
left.
11. To enter a descriptor for the next
zone, press [
✱
]
plus the desired
zone number (e.g.,
✱
02. The
summary display following step 4
previously will appear.
Now repeat steps 6 through 10 for
the descriptor for the next zone.
previously will appear.
Now repeat steps 6 through 10 for
the descriptor for the next zone.
12. To exit the Alpha descriptor mode,
press “
✱
00” at the summary display.
P r o g r a m A lph a ?
0
0
=
No , 1
=
Ye s 0 0
This prompt will be displayed.
A lph a P g m
8 2
13. Press “0”. This will be displayed.
14. Press
✱
99 to exit the programming
mode.
Alternate Method For Programming Zone Descriptors
When entering the Zone
Descriptors using this
method, the keypad keys
perform the following
functions:
[3] Scrolls both alphabet and
Descriptors using this
method, the keypad keys
perform the following
functions:
[3] Scrolls both alphabet and
actual words in
ascending
alphabetical order.
[1] Scrolls both alphabet and
actual words in
descend-
ing alphabetical order.
[6] Selects between alpha bet
and actual word list; also
used to save words.
used to save words.
[8] Stores the zone descrip-
tion in memory.
1.
Perform steps 1 through 5 of the previous method.
2.
Note that the first letter of the alphabet appears after the zone number,
and that the zone number is automati cally included with the description.
and that the zone number is automati cally included with the description.
If
there already is a de scription for the zone, the description will appear (with
no cur sor, since this is a display mode).
no cur sor, since this is a display mode).
To enter or change a de scription,
press [
✱
] + Zone Number again. A flashing cursor will now appear.
Assume, for example, that the desired description for zone 1 is BACK
DOOR.
DOOR.
3.
Select the first letter of the desired description (note that "A" is already
displayed).
Press key [3] repeatedly to advance through the al phabet (e.g., to "B"), or
key [1] to go backward. Then press [6] to display the first available word
beginning with the desired letter (e.g., BABY).
Next, press [3] repeatedly to move forward, or [1] to move backward, until
the desired word is displayed (e.g., BACK). Then press [6] to accept the
word and toggle back to the alphabet list.
displayed).
Press key [3] repeatedly to advance through the al phabet (e.g., to "B"), or
key [1] to go backward. Then press [6] to display the first available word
beginning with the desired letter (e.g., BABY).
Next, press [3] repeatedly to move forward, or [1] to move backward, until
the desired word is displayed (e.g., BACK). Then press [6] to accept the
word and toggle back to the alphabet list.